2018 Lexus LC500 light

188
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
■Turning the automatic mode off
While the vehicle is stopped, pull and
hold the parking brake switch until a
message is shown on the multi-infor-
mation display
■Parking brake operation
●When the engine switch
is not in IGNITION ON mode , the parking brake cannot be released using the parking brake switch.
●When the engine switch is not in IGNITION ON mode mode>, automatic mode (automatic brake setting and releasing) is not avail-
able.
■Parking brake automatic release func- tion
●When the shift position is shifted from P, the parking brake will be released in automatic mode.
●When all of the following conditions are met in manual mode, the parking brake
can be released by depressing the accel- erator pedal.• The driver’s door is closed
• The driver is wearing the seat belt • The shift position is in D, M or R
■If “EPB frequently operated Wait a min-ute” is displayed on the multi-informa-
tion display
If the parking brake is operated repeatedly
over a short period of time, the system may restrict operation to prevent overheating. If this happens, refrain from operating the
parking brake. Normal operation will return
after about 1 minute.
■If “EPB Activation Stopped Incom- pletely” or “EPB unavailable” is dis-played on the multi-information display
Operate the parking brake switch. If the message does not disappear after operat-
ing the switch several times, the system may be malfunctioning. Have the vehicle inspected by any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer.
■Parking brake operation sound
When the parking brake operates, a motor sound (whirring sound) may be heard. This does not indicate a malfunction.
■Parking brake indicator light
●Depending on the engine switch mode, the parking brake indica-
tor light will turn on and stay on as described below:IGNITION ON mode :
Comes on until the parking brake is released.Not in IGNITION ON mode mode>: Stays on for approximately 15 seconds.
●When the engine switch is turned off with the parking brake set,
the parking brake indi cator light will stay on for about 15 seconds. This does not indicate a malfunction.
■When the parking brake switch mal-
functions
Automatic mode (automatic brake setting
and releasing) will be turned on automati- cally.
■Parking the vehicle
 P.154
■Parking brake engaged warning buzzer
A buzzer will sound if the vehicle is driven
with the parking brake engaged. “EPB applied” is displayed on the multi-informa-tion display (with the vehicle reached a
speed of 5 km/h [3 mph]).

189
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
■If the brake system warning light comes on
 P.368
■Usage in winter time
 P.269
Press the brake hold switch to turn the
system on
The brake hold standby indicator
comes on. While the system is holding the
brake, the brake hold operated indicator
comes on.
■Brake hold system operating conditions
The brake hold system cannot be turned on
WARNING
■When parking the vehicle
Do not leave a child in the vehicle alone. The parking brake may be released unin-tentionally and there is the danger of the
vehicle moving that may lead to an acci- dent resulting in death or serious injury.
NOTICE
■When parking the vehicle
Before you leave the vehicle, shift the shift position to P, set the parking brake and make sure that the vehicle does not
move.
■When the system malfunctions
Stop the vehicle in a safe place and
check the warning messages.
■When the parking brake cannot be released due to a malfunction
Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking
performance and increase brake wear. Have the vehicle inspected by any autho-rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer immedi- ately if this occurs.
Brake Hold
The brake hold system keeps the
brakes applied when the vehicle is
stopped by depressing the brake
pedal. This system can be used
when in a traffic jam or waiting for a
traffic light to change.
This system keeps the brake
applied when the shift position is in
D, M or N with the system on and
the brake pedal has been
depressed to stop the vehicle. The
system releases the brake when the
accelerator pedal is depressed with
the shift position in D or M to allow
smooth start off.
Enabling the system
A
B

190
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
in the following conditions:
●The driver’s door is not closed.
●The driver is not wearing the seat belt.
●“EPB Activation Stopped Incompletely” or “EPB Malfunction Visit Your dealer” is displayed on the multi-information dis-
play.
If any of the conditions above are detected
when the brake hold system is enabled, the system will turn off and the brake hold standby indicator light will go off. In addi-
tion, if any of the conditions are detected while the system is holding the brake, a warning buzzer will sound and a message
will be shown on the multi-information dis- play. The parking brake will then be set automatically.
■Brake hold function
●If the brake pedal is left released for a period of about 3 minutes after the sys-
tem has started holding the brake, the parking brake will be set automatically. In this case, a warning buzzer sounds and a
message is shown on the multi-informa- tion display.
●To turn the system off while the system is holding the brake, firmly depress the
brake pedal and press the button again.
●The brake hold function may not hold the
vehicle when the vehicle is on a steep incline. In this situation, it may be neces-sary for the driver to apply the brakes. A
warning buzzer will sound and the multi- information display will inform the driver of this situation. ( P.378)
■When the parking brake is set automati-
cally while the system is holding the brakes
The parking brake will not be released auto- matically. Perform one of the following pro-cedures to release the parking brake and
confirm that the parking brake indicator light turns off. ( P.187)
●With the brake pedal depressed, operate the parking brake switch.
●Fasten your seat belt, check that the shift position is in either D or R and slowly depress the accelerator pedal.
■If “Brake Hold Unavailable” is shown on the multi-information display
The brake hold system cannot be used. The reason the brake hold system is not avail-able (the driver’s door opens, the driver’s
seat belt is unfasten, or the hood or trunk opens) may be displayed. Use the brake hold system when it becomes available.
■Warning message and buzzers
Warning messages and buzzers are used to indicate a system malfunction or to inform
the driver of the need for caution. ( P.378)
WARNING
■When the vehicle is on a steep incline
When using the brake hold system on a
steep incline exercise caution. The brake hold function may not hold the vehicle in such a situation.
■When the vehicle is stopped on a slip-
pery road
The system cannot stop the vehicle when
the gripping ability of the tires has been exceeded. Do not use the system when the vehicle is stopped on a slippery road.
NOTICE
■When parking the vehicle
The brake hold system is not designed for use when parking the vehicle for a
long period of time. Turning the engine switch off while the sys- tem is holding the brake may release the
brake, which would cause the vehicle to move. When operating the engine switch , depress the brake pedal,
set the parking brake and shift the shift position to P.

191
4
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
Driving
4-3.Operating the lig hts and wipe rs
Turning the end of the lever turns on
the lights as follows:
1 The front position, tail, license
plate and instrument panel lights
turn on.
2 The headlights and all the
lights listed above turn on.
3 The headlights, daytime run-
ning lights ( P.191) and all the
lights listed above turn on and off
automatically.
■AUTO mode can be used when
The engine switch

is in
IGNITION ON mode .
■Daytime running light function
To make your vehicle more visible to other
drivers during daytime driving, the daytime running lights turn on automatically when-ever the engine is started
and the parking brake is released with the
headlight switch in the position. (Illumi-
nate brighter than the front position lights.) Daytime running lights are not designed for use at night.
■Headlight control sensor
The sensor may not function properly if an object is placed on the sensor, or anything
that blocks the sensor is affixed to the wind- shield. Doing so interferes with the sensor detect-
ing the level of ambient light and may cause the automatic headlight system to malfunc-tion.
■Automatic light off system
●When the light swit ch is in : The
headlights turn off automatically if the engine switch is turned to ACCESSORY mode or turned off.
●When the light swit ch is in : The
headlights and all the lights turn off auto- matically if the engine switch is turned to ACCESSORY mode
or turned off.
To turn the lights on again, turn the engine
switch to IGNITION ON mode , or turn the light switch
to position once and then back to
Headlight switch
The headlights can be operated
manually or automatically.
Turning on the headlights

192
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
or .
■Light reminder buzzer
A buzzer sounds when the engine switch is turned off or turned to ACCESSORY mode and the driver’s door
is opened while the lights are turned on.
■Automatic headlight leveling system
The level of the headlights is automatically adjusted according to the number of pas-sengers and the loading condition of the
vehicle to ensure that the headlights do not interfere with other road users.
■12-volt battery-saving function
In order to prevent 12-volt the battery of the vehicle from discharging, if the light switch
is in the or position when the
engine switch is turned off the 12-volt battery savi ng function will oper-
ate and automatically turn off all the lights after approximately 20 minutes.
When the engine switch is turned to IGNITION ON mode , the 12-volt battery-saving function
will be disabled.
When any of the following are performed,
the 12-volt battery-saving function is can- celed once and then reactivated. All the lights will turn off automatically 20 minutes
after the 12-volt battery- saving function has been reactivated:
●When the headlight switch is operated
●When a door is opened or closed
■Welcome light illumination control
The front position, tail lights and license plate lights automatically turn on at night
when the doors are unlocked using the entry function or wireless remote control if
the light switch is in the position.
■Customization
Settings (e.g. light sens or sensitivity) can be
changed. (Customizable features: P.423)
1With the headlights on, push the
lever away from you to turn on the
high beams.
Pull the lever toward you to the center
position to turn the high beams off.
2 Pull the lever toward you and
release it to flash the high beams
once.
You can flash the high beams with the
headlights on or off.
This system allows the headlights and
front position lights to be turned on for
30 seconds when the engine switch
is off.
Pull the lever toward you and release it
with the light switch is in after turn-
ing the engine switch
off.
NOTICE
■To prevent 12-volt battery discharge
Do not leave the lights on longer than
necessary when the engine is not running .
Turning on the high beam head-
lights
Follow me home system

193
4
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
Driving
Pull the lever toward you and release it
again to turn off the lights.
When any of the following conditions is
met, while the headlights (low beam)
are on, the cornering lights will addi-
tionally turn on and light up the direc-
tion of movement for the vehicle. This is
to ensure excellent visibility when
either driving at intersections or park-
ing at night.
 The steering wheel is operated
 The turn signal lever is operated
 The shift position is in R (both left
and right side cornering lights)
■Cornering light control
●The lights illuminate when the vehicle speed is approximately 30 km/h (19
mph) or less. However, the lights turn off when the vehicle speed increases to approximately 35 km/h (22 mph) or
more.
●After the lights remain illuminated for 30
minutes, they automatically turn off.
*:If equipped
1 Push the lever away from you with
the headlight switch in the or
position.
2 Press the Automatic High Beam
switch.
Cornering lights
Automatic High Beam*
The Automatic High Beam uses an
in-vehicle camera sensor to assess
the brightness of streetlights, the
lights of a vehicle ahead, etc., and
automatically turns the high beam
on or off as necessary.
WARNING
■Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to observe your surroundings and turning
the high beam on or off manually if nec- essary.
■To prevent incorrect operation of the Automatic High Beam system
Do not overload the vehicle.
Activating the Automatic High
Beam system

194
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
The Automatic High Beam indicator will come on when the headlights are turned on automatically to indicate that the system
is active.
■High beam automatic turning on or off
conditions
●When all of the following conditions are
met, the high beam will be automatically turned on (after approximately 1 second):• Vehicle speed is above approximately 40
km/h (25 mph). • The area ahead of the vehicle is dark.• There are no vehicles ahead with head-
lights or tail lights turned on. • There are few streetlights on the road ahead.
●If any of the following conditions are met, the high beam will be automatically
turned off: • Vehicle speed drops below approxi-mately 30 km/h (19 mph).
• The area ahead of the vehicle is not dark. • Vehicles ahead have headlights or tail lights turned on.
• There are many streetlights on the road ahead.
■Camera sensor detection information
●The high beam may not be automatically turned off in the following situations:• When oncoming vehicles suddenly
appear from a curve • When the vehicle is cut in front of by another vehicle
• When vehicles ahead are hidden from sight due to repeated curves, road divid-ers or roadside trees
• When vehicles ahead appear from the faraway lane on wide road
• When vehicles ahead have no lights
●The high beam may be turned off if a
vehicle ahead that is using fog lights with- out using the headlights is detected.
●House lights, street lights, traffic signals, and illuminated billboards or signs may cause the high beam to switch to the low
beams, or the low beams to remain on.
●The following factors may affect the
amount of time taken to turn the high beam on or off:• The brightness of headlights, fog lights,
and tail lights of vehicles ahead • The movement and direction of vehicles ahead
• When a vehicle ahead only has opera- tional lights on one side• When a vehicle ahead is a two-wheeled
vehicle • The condition of the road (gradient, curve, condition of the road surface etc.)
• The number of passengers and amount of luggage
●The high beam may be turned on or off when the driver does not expect it.
●Bicycles or similar objects may not be detected.
●In the situations shown below, the system may not be able to accurately detect sur-
rounding brightness levels. This may cause the low beams to remain on or the high beams to cause problems for pedes-
trians, vehicles ahead or other parties. In these cases, manually switch between the high and low beams.
• In bad weather (rain, snow, fog, sand- storms etc.)• The windshield is obscured by fog, mist,
ice, dirt etc. • The windshield is cracked or damaged.• The camera sensor is deformed or dirty.
• Surrounding brightness levels are equal to those of headlights, tail lights or fog lights.
• Vehicles ahead have headlights or tail lights that are either switched off, dirty, changing color, or have improperly
adjusted aim. • When driving through an area of inter-mittently changing brightness and dark-

195
4
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
Driving
ness. • When frequently and repeatedly driving ascending/descending roads, or roads
with rough, bumpy or uneven surfaces (such as stone-paved roads, gravel tracks etc.).
• When frequently and repeatedly taking curves or driving on a winding road.• There is a highly reflective object ahead
of the vehicle, such as a sign or a mirror. • The vehicle’s headlights are damaged or dirty.
• The vehicle is listing or titling, due to a flat tire, a trailer being towed etc.• The driver believes that the high beam
may be causing problems or distress to other drivers or pedestrians nearby.• The vehicle is used in a territory in which
vehicles travel on the opposite side of the road of the country for which the vehicle is approved, for example using a vehicle
designed for right-hand traffic in a left- hand traffic territory, or vice versa.
■Switching to low beam
Pull the lever to the original position.
The Automatic High Beam indicator will
turn off.
Push the lever away from you to activate
the Automatic High Beam system again.
■Switching to high beam
Press the Automatic High Beam
switch.
The Automatic High Beam indicator will
turn off and the high beam indicator will
turn on.
Press the switch to activate the Automatic
High Beam system again.
Turning the high beam on/off
manually