2018 Lexus LC500 flat tire

330
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
display. (P.92)
The illustration used is intended as an
example, and may differ from the image
that is actually displayed on the multi-infor-
mation display.
■Routine tire inflation pressure checks
The tire pressure warning system does not
replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily
vehicle checks.
■Situations in which the tire pressure warning system may not operate prop-
erly
●In the following cases, the tire pressure
warning system may not operate prop- erly.• If non-genuine Lexus wheels are used.
• A tire has been replaced with a tire that is not an OE (Original Equipment) tire.• A tire has been replaced with a tire that is
not of the specified size. • Tire chains etc. are equipped.• An auxiliary-supported run-flat tire is
equipped. • If a window tint that affects the radio wave signals is installed.
• If there is a lot of snow or ice on the vehi- cle, particularly around the wheels or wheel housings.
• If the tire inflation pressure is extremely higher than the specified level.• If wheels without tire pressure warning
valves and transmitters are used. • If the ID code on the tire pressure warn-ing valves and transmitters is not regis-
tered in the tire pressure warning
computer.
●Performance may be affected in the fol-
lowing situations. • Near a TV tower, electric power plant, gas station, radio station, large display,
airport or other facility that generates strong radio waves or electrical noise• When carrying a portable radio, cellular
phone, cordless phone or other wireless communication device
If tire position information is not correctly
displayed due to the radio wave conditions,
the display may be corrected by driving and
changing the radio wave conditions.
●When the vehicle is parked, the time taken for the warning to start or go off
could be extended.
●When tire inflation pressure declines rap-
idly for example when a tire has burst, the warning may not function.
■Warning performance of the tire pres-sure warning system
The warning of the tire pressure warning system will change in accordance with the
conditions under which it was initialized. For this reason, the system may give a warning
even if the tire pressure does not reach a low enough level, or if the pressure is higher than the pressure that was adjusted to when
the system was initialized.

335
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
When replacing tires or wheels, tire
pressure warning valves and transmit-
ters must also be installed.
When new tire pressure warning
valves and transmitters are installed,
new ID codes must be registered in the
tire pressure warning computer and
the tire pressure warning system must
be initialized. ( P.337)
■When replacing the tires and wheels
If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work
properly. After driving for about 10 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system
malfunction.
■The tire pressure warning system
must be initialized in the following
circumstances:
 When rotating the tires.
 When the tire inflation pressure is
changed when changing traveling
speed.
 When the tire inflation pressure is
changed such as when changing tire
size. (When there are multiple spec-
ified pressures)
 After registering the ID codes.
( P.337)
When the tire pressure warning system
is initialized, the current tire inflation
pressure is set as the benchmark pres-
sure.
■How to initialize the tire pressure
warning system
1 Park the vehicle in a safe place and
turn the engine switch switch> off.
Initialization cannot be performed while the vehicle is moving.
2 Adjust the tire inflation pressure to
the specified cold tire inflation pres-
sure level.
Make sure to adjust the tire pressure to the specified cold tire infl ation pressure level. The tire pressure warning system will oper-
ate based on this pressure level.
3 Turn the engine switch switch> to IGNITION ON mode
.
Installing tire pressure warning
valves and tr ansmitters
NOTICE
■Repairing or replacing tires, wheels, tire pressure warning valves, trans-
mitters and tire valve caps
●When removing or fitting the wheels,
tires or the tire pressure warning valves and transmitters, contact any
authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer as the tire pressure warning
valves and transmitters may be dam- aged if not handled correctly.
●Make sure to install the tire valve caps. If the tire valve caps are not installed,
water could enter the tire pressure warning valves and the tire pressure warning valves could be bound.
●When replacing tire valve caps, do not
use tire valve caps other than those specified. The cap may become stuck.
Initializing the tire pressure
warning system

336
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
4Press or of the meter con-
trol switches and select .
5 Press or of the meter con-
trol switches and select “Vehicle
Settings”, and then press “OK”.
6 Press or of the meter con-
trol switches and select “TPWS
SET”, and then press “OK”.
7 Press or of the meter con-
trol switches and select “Set tire
pressure”, and then press and hold
“OK” until the tire pressure warning
light starts blinking.
A message is displayed on the multi-infor- mation display. Also, “--” is displayed for inflation pressure of each tire on the multi-
information display while the tire pressure warning system determines the position.
8 Drive the vehicle at approximately
40 km/h (25mph) or more for
approximately 10 to 30 minutes.
When initialization is complete, the infla- tion pressure of each tire will be displayed on the multi-information display.
Depending on the vehicle and driving con- ditions, initialization may take up to
approximately 1 hour to complete.
■The initialization operation
●Make sure to carry out initialization after
adjusting the tire inflation pressure. Also, make sure the tires are cold before carrying out initialization or tire inflation
pressure adjustment.
●If you have accidentally turned the engine
switch off during initial- ization, it is not ne cessary to manually restart the initializatio n again, as initializa-
tion will restart automatically the next time the engine switch is turned to IGNITION ON mode mode>.
●If you accidentally perform initialization
when initialization is not necessary, adjust the tire inflation pressure to the specified level when the tires are cold, and conduct
initialization again.
●While the position of each tire is being
determined and the inflation pressures are not being displayed on the multi-information display, if the inflation pres-
sure of a tire drops, the tire pressure warning light will come on.
■When initialization of the tire pressure warning system has failed
Initialization may take longer to complete if
the vehicle is driven on an unpaved road. When performing initialization, drive on a paved road if possible. Depending on the
driving environment an d condition of the tires, initialization will be completed in approximately 10 to 30 minutes. If initializa-
tion is not complete after driving approxi- mately 10 to 30 minutes, continue driving for a while. If the inflation of each tire is not
displayed after driving for approximately 1 hour, perform the following procedure.
●Park the vehicle in a safe place for approximately 20 minutes. Then drive straight (with occasional left and right
turns) at approximately 40 km/h (25 mph) or more for approximately 10 to 30 minutes.
However, in the following situations, the tire
inflation pressure will not be recorded and
the system will not operate properly. Per-
form initialization again.
●When performing init ialization, the tire

337
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
pressure warning light does not blink 3 times. (Initialization will not occur while driving)
●After performing init ialization, the tire pressure warning light blinks for 1 minute
then stays on after driving for about 20 minutes.
If the inflation pressure of each tire is still not
displayed, have the vehicle inspected by
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
■When registering ID codes
●Initialize the tire pressure warning system after ID code registra tion. Initialization is
disabled if the system was initialized before registration.
●After ID code registration, the tires are hot by driving. Initia lize the tire pressure warning system after the tires become
cold.
The tire pressure warning valve and
transmitter is equipped with a unique
ID code. When replacing a tire pres-
sure warning valve and transmitter, it is
necessary to register the ID code.
When registering the ID codes, per-
form the following procedure.
1 Turn the engine switch switch> to IGNITION ON mode
.
2 Press or of the meter con-
trol switches and select .
3 Press or of the meter con-
trol switches and select “Vehicle
Settings”, and then press “OK”.
4 Press or of the meter con-
trol switches and select “TPWS
SET”, and then press “OK”.
5 Press or of the meter con-
trol switches and select “Change
wheel set”, and then press and hold
“OK” until the tire pressure warning
light starts blinking.
The change wheel set mode is activated and registration is started.
A message is displayed on the multi-infor- mation display, and “--” is displayed for inflation pressure of e ach tire. Then, the tire
pressure warning light blinks rapidly for approximately 1 minute and stays on.
6 Drive the vehicle at 40 km/h
(25mph) or more for approxi-
mately 10 to 30 minutes.
When registration is completed, the tire pressure warning light will go off and the inflation pressure of each tire will be dis-
played on the multi-information display.
WARNING
■When initializing the tire pressure
warning system
Do not initialize tire inflation pressure
without first adjusting the tire inflation pressure to the specified level. Other-wise, the tire pressure warning light may
not come on even if the tire inflation pres- sure is low, or it may come on when the tire inflation pressure is actually normal.
Registering ID codes

339
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
Stop the vehicle in a safe place on a
hard, flat surface.
 Set the parking brake.
 Shift the shift position to P.
 Turn off the intrusion sensor and tilt
sensor ( P.78)
 Stop the engine .
Screwdriver
Wheel nut wrench
Jack
Jack handle
Towing eyelet
Replacing the tire
When raising your vehicle with a
jack, position the jack correctly.
Improper placement may damage
your vehicle or cause injury.
If necessary tire replacement
seems difficult to perform, contact
any authorized Lexus retailer or
Lexus authorized repairer, or any
reliable repairer.
Before jacking up the vehicle
Location of the jack and tools
A
B
C
D
E

345
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
■Effects of incorrect tire inflation pres- sure
Driving with incorrect tire inflation pressure may result in the following:
●Reduced fuel economy
●Reduced driving comfort and poor han-dling
●Reduced tire life due to wear
●Reduced safety
●Damage to the drivetrain
If a tire needs frequent inflating, have it checked by any authorized Lexus retailer or Lexus authorized repairer, or any reliable
repairer.
■Instructions for checking tire inflation pressure
When checking tire inflation pressure, observe the following:
●Check only when the tires are cold.If your vehicle has been parked for at least 3 hours or has not been driven for
more than 1.5 km or 1 mile, you will get an accurate cold tire inflation pressure read-ing.
●Always use a tire pressure gauge.It is difficult to judge if a tire is properly
inflated based only on its appearance.
●It is normal for the tire inflation pressure
to be higher after driving as heat is gen- erated in the tire. Do not reduce tire infla-tion pressure after driving.
●Passengers and luggage weight should be placed so that the vehicle is balanced.
Tire inflation pressure
Make sure to maintain proper tire
inflation pressure. Tire inflation
pressure should be checked at least
once per month. However, Lexus
recommends that tire inflation
pressure be checked once every
two weeks.
WARNING
■Proper inflation is critical to save tire performance
Keep your tires properly inflated. If the tires are not properly inflated, the following conditions may occur which
could lead to an accident resulting in death or serious injury:
●Excessive wear
●Uneven wear
●Poor handling
●Possibility of blowouts resulting from overheated tires
●Air leaking from between tire and
wheel
●Wheel deformation and/or tire dam- age
●Greater possibility of tire damage while driving (due to road hazards,
expansion joints, sh arp edges in the road, etc.)
NOTICE
■When inspecting and adjusting tire inflation pressure
Be sure to put the tire valve caps back on. If a valve cap is not installed, dirt or mois-
ture may get into the valve and cause an air leak, resulting in decreased tire infla-tion pressure.

346
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
When replacing wheels, care should
be taken to ensure that they are equiv-
alent to those removed in load capac-
ity, diameter, rim width and inset*.
Replacement wheels are available at
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
*: Conventionally referred to as offset.
Lexus does not recommend using the
following:
 Wheels of different sizes or types
 Used wheels
 Bent wheels that have been straight-
ened
■When replacing wheels
The wheels of your vehicle are equipped with tire pressure warning valves and trans-
mitters that allow the tire pressure warning system to provide advance warning in the event of a loss in tire inflation pressure.
Whenever wheels are replaced, tire pres- sure warning valves and transmitters must be installed. ( P.335)Use only Lexus wheel nuts and
wrenches designed for use with
your aluminum wheels.
 When rotating, repairing or chang-
Wheels
If a wheel is bent, cracked or heavily
corroded, it should be replaced.
Otherwise, the tire may separate
from the wheel or cause a loss of
handling control.
Wheel selection
WARNING
■When replacing wheels
●Do not use wheels that are a different
size from those recommended in the Owner’s Manual, as this may result in a loss of handling control.
●Never use an inner tube in a leaking
wheel which is designed for a tubeless tire. Doing so may result in an acci-dent, causing death or serious injury.
■Use of defective wheels prohibited
Do not use cracked or deformed wheels.
Doing so could cause the tire to leak air during driving, possibly causing an acci-dent.
NOTICE
■Replacing tire pressure warning
valves and transmitters
●Because tire repair or replacement
may affect the tire pressure warning valves and transmitters, make sure to have tires serviced by any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer or other qualified service shop. In addi-
tion, make sure to purchase your tire pressure warning valves and transmit-ters at any authorized Lexus retailer or
Lexus authorized repairer, or any reli- able repairer.
●Ensure that only genuine Lexus wheels are used on your vehicle.
Tire pressure warning valves and trans- mitters may not work properly with non-genuine wheels.
Aluminum wheel precautions

7
359
-$@-$I@0.@0.&@ &&

7
When trouble arises
When trouble arises
7-1. Essential information
Emergency flashers ................. 360
If your vehicle has to be stopped in
an emergency.......................... 360
7-2. Steps to take in an emergency
If your vehicle needs to be towed
........................................................ 362
If you think something is wrong
........................................................ 366
Fuel pump shut off system
(LC500) ................................... 367
If a warning light turns on or a
warning buzzer sounds ....... 368
If a warning message is displayed
........................................................ 378
If you have a flat tire.................. 384
If the engine will not start
(LC500) ................................... 385
If the hybrid system will not start
(LC500h) ................................. 386
If you lose your keys ................. 388
If the fuel filler door cannot be
opened ....................................... 388
If the electronic key does not
operate properly .................... 389
If the 12-volt battery is discharged
........................................................ 392
If your vehicle overheats
(LC500) ................................... 400
If your vehicle overheats
(LC500h) ................................. 403
If the vehicle becomes stuck 407