2018 Lexus LC500 check engine

112
-$@-$I@0.@0.&@ &&

3-1. Key information
3-1.Key information
The following keys are provided with
the vehicle.
Electronic keys
• Operating the smart entry & start sys-
tem ( P.122)
• Operating the wireless remote control
function
Mechanical keys
Key number plate
■When riding in an aircraft
When bringing an electronic key onto an aircraft, make sure you do not press any buttons on the electronic key while inside
the aircraft cabin. If you are carrying an electronic key in your bag etc., ensure that the buttons are not likely to be pressed acci-
dentally. Pressing a button may cause the electronic key to emit radio waves that could interfere with the operation of the air-
craft.
■Electronic key battery depletion
●The standard battery life is 1 to 2 years.
●If the battery becomes low, an alarm will sound in the cabin when the engine
is stopped.
●As the electronic key always receives
radio waves, the battery will become depleted even if the electronic key is not
used. The following symptoms indicate that the electronic key battery may be depleted. Replace the battery when nec-
essary. ( P.349) • The smart entry & start system or the wireless remote control does not oper-
ate. • The detection area becomes smaller.• The LED indicator on the key surface
does not turn on.
●To avoid serious deterioration, do not
leave the electronic key within 1 m (3 ft.) of the following electrical appliances that produce a magnetic field:
•TVs •Personal computers• Cellular phones, cordless phones and
battery chargers • Recharging cellular phones or cordless phones
• Table lamps •Induction cookers
■Replacing the battery
 P.349
■Confirmation of the registered key number
The number of keys already registered to the vehicle can be confirmed. Ask any
authorized Lexus retailer or Lexus autho- rized repairer, or any reliable repairer for details.
■If “A New Key has been Registered
Contact Your Dealer for Details” is shown on the multi-information display
This message will be displayed each time the driver’s door is opened when the doors are unlocked from the outside for approxi-
mately 10 days after a new electronic key has been registered. If this message is displayed but you have not
had a new electronic key registered, ask any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer
to check if an unknown electronic key (other than those in your possession) has been registered.
Keys
Key types
A
B
C

121
3
-$@-$I@0.@0.&@ &&

3-2. Opening, closing and locking the doors and trunk
Before driving
■Wireless remote control
Press and hold the switch.
■Trunk light
●The trunk light turns on when the trunk is opened.
●If the trunk light is le ft on when the engine switch is turned off, the
light will go off automatically after 20 minutes.
■Function to prevent the trunk being locked with the electronic key inside
●When both side doors are locked, closing the trunk lid with the electronic key left
inside the trunk will sound an alarm. In this case, the trunk lid can be opened by pressing the trunk release button on
the trunk lid.
●If the spare electronic key is put in the
trunk with both side doors locked, the key confinement prevention function is acti-vated so the trunk can be opened. In
order to prevent theft, take all electronic keys with you when leaving the vehicle.
●If the electronic key is put in the trunk with both side doors locked, the key may not
be detected depending on the location of the key and the surrounding radio wave conditions. In this case, the key confine-
ment prevention function cannot be acti- vated, causing the trunk to be locked when the trunk lid is closed. Make sure to
check where the key is before closing the trunk.
●The key confinement prevention function cannot be activated if either door is unlocked. In this case, open the trunk
using the trunk opener switch.
●If the trunk lid is closed by a hand having
the electronic key when the both side doors are locked, a warning buzzer may sound. In this case, the trunk is not locked.
Do not close the trunk lid by a hand hav- ing the electronic key.
■If the smart entry & start system or the wireless remote control does not oper-
ate properly
Use the trunk opener switch to unlock the
trunk. ( P.389) Replace the key battery with a new one if it is depleted. ( P.349)
■If a symbol indicating the trunk opens is
shown on the multi-information display
 P.118
■If the 12-volt battery is discharged
The trunk cannot be locked and unlocked
using the smart entry & start system or wireless remote control. Lock or unlock the trunk using the mechanical key. ( P.392)
■Customization
The trunk unlocking operation can be changed. (Customizable features:
 P.423)
Using the trunk grip, lower the trunk
without applying force to the side and
push the trunk down from the outside
to close it.
Closing the trunk

125
3
-$@-$I@0.@0.&@ &&

3-2. Opening, closing and locking the doors and trunk
Before driving
• The electronic key is near the ground or in a high place, or too close to the center of the rear bumper when the trunk is
opened. • The electronic key is on the instrument panel, rear package tray or floor, or in the
door pockets or glove box when the engine is started or engine switch modes are
changed.
●Do not leave the electronic key on top of
the instrument panel or near the door pockets when exiting the vehicle. Depending on the radio wave reception
conditions, it may be detected by the antenna outside the cabin and the doors will become lockable from the outside,
possibly trapping the electronic key inside the vehicle.
●As long as the electronic key is within the effective range, the doors may be locked or unlocked by anyone. However, only
the doors detecting the electronic key can be used to unlock the vehicle.
●Even if the electronic key is not inside the vehicle, it may be possible to start the engine if the electronic
key is near the window.
●The doors may unlock or lock if a large amount of water splashes on the door handle, such as in the rain or in a car
wash, when the electronic key is within the effective range. (The doors will auto- matically be locked after approximately
30 seconds if the doors are not opened and closed.)
●If the wireless remote control is used to lock the doors when the electronic key is near the vehicle, there is a possibility that
the door may not be unlocked by the entry function. (Use the wireless remote control to unlock the doors.)
●If the door handle becomes wet while the electronic key is within the effective
range, the door may lock and unlock repeatedly. In this case, follow the follow-ing correction procedures to wash the
vehicle: • Place the electronic key in a location 2 m (6 ft.) or more away from the vehicle.
(Take care to ensure that the key is not stolen.)• Set the electronic key to battery-saving
mode to disable the smart entry & start system. ( P.124)
●If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a message may be shown on
the multi-information display and a buzzer will sound outside the vehicle. To turn off the alarm, lock both side doors.
●If an outside door handle is not retracted during a car wash, a door may be opened
or an outside door handle may be dam- aged. Make sure that the outside door handles are retracted before using the
car wash.
●A sudden handle operation or a handle
operation immediately after entering the effective range may prevent the doors from being unlocked. Touch the door
unlock sensor and check that the doors are unlocked before pulling the door handle again.
●Unlocking the vehicle may take more time if another electronic key is within the
effective range.
■When the vehicle is not driven for extended periods
●To prevent theft of the vehicle, do not leave the electronic key within 2 m (6 ft.)
of the vehicle.
●The smart entry & start system can be
deactivated in advance.
■To operate the system properly
●Make sure to carry the electronic key
when operating the system. Do not get the electronic key too close to the vehicle when operating the system from the out-
side of the vehicle. Depending on the position and holding condition of the electronic key, the key
may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door
lock prevention function may not oper- ate.)
●Do not leave the electronic key inside the

139
3
-$@-$I@0.@0.&@ &&

3-3. Adjusting the seats
Before driving
■Before entering/exiting the rear
seats
 Remove the seat belt from the seat
belt guide. ( P.32)
 Stow the sun visor.
■Entering/exiting the rear seat
1 Pull the lever.
The front seat will lower automatically.
2Fold the seatback completely for-
ward.
The front seat will move forward and the
head restraint will move downward* auto- matically.
*: Power type only
■Returning the front seat to its origi-
nal position
Move the seatback backward until it
locks. The front seat will return to its
original position automatically.
■Lever-operated “Front, Fold & Return” seat
●After the front seat is moved forward by operating the “Front, Fold & Return” seat
lever, if a power seat adjusting switch or a driving position memory switch is pressed, the front seat will not return to its
original position even if the front seatback is moved backward until it locks.
●The lever-operated “Front, Fold & Return” seat will not operate in the follow-
ing situations: • The seat belt of the seat to be operated is fastened.
• The engine switch is in IGNITION ON mode and the shift position is in a position other than
P.
●Operation of the lever-operated “Front,
Fold & Return” seat will stop in the follow- ing situations:• A power seat adjusting switch or a driv-
ing position memory switch is pressed. • The seat belt of the seat which is operat-ing is fastened.
• The engine switch is in IGNITION ON mode and the shift position is changed to a position
other than P.
■Jam protection function
While the driving positi on is recalling or the
lever-operated “Front, Fold & Return” seat is operating, if an object is stuck either in front of or behind the front seat, the front
seat will stop and then move in the opposite direction slightly.
When the jam protection function operates, the seat stops at a po sition other than the set seat position. Check the seat position.
Entering/exiting the rear seats
(lever-operated “Front, Fold &
Return” seat)

140
-$@-$I@0.@0.&@ &&

3-3. Adjusting the seats
1Turn the engine switch switch> to IGNITION ON mode
.
2 Check that the shift position is in P.
3 Adjust the driver’s seat, steering
wheel, outside rear view mirrors
and head-up display to the desired
positions.
4 While pressing the “SET” button, or
within 3 seconds after the “SET”
button is pressed, press button “1”,
“2” or “3” until the buzzer sounds.
If the selected button has already been preset, the previously recorded position
WARNING
■Lever-operated “Front, Fold & Return” seat
●Before operating the lever-operated “Front, Fold & Return” seat, ensure that any surrounding passengers or objects
will not contact the seat.
●Make sure the seatback is locked securely before driving.
●Never operate the lever-operated “Front, Fold & Return” seat while the
vehicle is moving.
■Jam protection function
Do not use a hand, foot, or any other part
of your body to intentionally activate the jam protection function.
Driving position memory
This feature automatically adjusts
the positions of the driver’s seat,
steering wheel, outside rear view
mirrors and head-up display (if
equipped) to suit your preferences.
Up to 3 different driving positions
can be recorded.
Each electronic key can be regis-
tered to recall your preferred driv-
ing position.
Recording a driving position into
memory

141
3
-$@-$I@0.@0.&@ &&

3-3. Adjusting the seats
Before driving
will be overwritten.
■Seat positions that can be memorized
( P.138)
The adjusted positions other than the posi-
tion adjusted by lumbar support switch can be recorded.
■In order to correctly use the driving position memory function
If a seat position is already in the furthest possible position and the seat is operated in
the same direction, the recorded position may be slightly different when it is recalled.
1 Turn the engine switch switch> to IGNITION ON mode
.
2 Check that the shift position is in P.
3 Press one of the buttons for the
driving position you want to recall
until the buzzer sounds.
■To stop the position recall operation
part-way through
Perform any of the following:
●Press the “SET” button.
●Press button “1”, “2” or “3”.
●Operate any of the seat adjustment
switches (only cancels seat position recall).
●Operate the tilt and telescopic steering control switch (only cancels steering
wheel position recall).
■Operating the driving position memory after turning the engine switch off
Recorded seat positions can be activated up to 180 seconds after the driver’s door is
opened and another 60 seconds after it is closed again.
■Registering procedure
Record your driving position to button
“1”, “2” or “3” before performing the
following:
WARNING
■Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passen-
ger or squeeze your body against the steering wheel.
Recalling a driving position
Registering/cancel ing/recalling
a driving position to an elec-
tronic key (memor y recall func-
tion)

142
-$@-$I@0.@0.&@ &&

3-3. Adjusting the seats
Carry only the key you want to register,
and then close the driver’s door.
If 2 or more keys are in the vehicle, the
driving position cannot be recorded
properly.
1 Turn the engine switch switch> to IGNITION ON mode
.
2 Check that the shift position is in P.
3 Recall the driving position that you
want to record.
4 While pressing the recalled button,
press and hold the door lock switch
(either lock or unlock) until the
buzzer sounds.
If the button could not be registered, the buzzer sounds continuously for approxi-mately 3 seconds.
■Cancelation procedure
1 Carry only the key you want to can-
cel and then close the driver’s door.
If 2 or more keys are in the vehicle, the driving position cannot be canceled prop-erly.
2 Turn the engine switch switch> to IGNITION ON mode
.
3 While pressing the “SET” button,
press and hold the door lock switch
(either lock or unlock) until the
buzzer sounds twice.
If the button could not be canceled, the buzzer sounds continuously for approxi-
mately 3 seconds.
■Recall procedure
1 Make sure that the doors are
locked before recalling the driving
position. Carry the electronic key
that has been registered to the driv-
ing position, and then unlock and
open the driver’s door using the
smart entry & start system or wire-
less remote control.
The driving position will move to the recorded position (not including the steer-
ing wheel and head-up display).
If the driving position is in a position that
has already been recorded, the seat and outside rear view mirrors will not move.
2 Turn the engine switch switch> to ACCESSORY mode or
IGNITION ON mode mode>.
The steering wheel and head-up display will move to the recorded position.
■Recalling the driving position using the
memory recall function
●Different driving positions can be regis-
tered for each electronic key. Therefore, the driving position that is recalled may be different depending on the key being
carried.
●If the passenger’s door is unlocked with
the smart entry & start system, the driving position cannot be recalled. In this case, press the driving position button which
has been set.
■Customization
The unlock door settings of the memory
recall function can be changed. (Customizable features: P.423)

151
3
-$@-$I@0.@0.&@ &&

3-5. Opening, closing the windows
Before driving
again. After the door window is com- pletely closed, continue holding the switch for a further 1 second or more.
If you release the switch while the window is moving, start again from the beginning.
If the window reverses and cannot be fully closed or opened, have the vehicle inspected by any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer.
■Door lock linked window operation
●The power windows can be opened and
closed using the mechanical key.*
( P.389)
●The power windows can be opened and
closed using the wireless remote con-
trol.* ( P.115)
*: These settings must be customized at any
authorized Lexus retailer or Lexus autho-
rized repairer, or any reliable repairer.
■Power windows open warning buzzer
The buzzer sounds and “Window Open” is
shown on the multi-information display in the instrument cluster when the engine switch is turned off and the
driver’s door is opened with the power win- dows open.
■Customization
Settings (e.g. linked door lock operation) can be changed. (Customizable features: P.423)
WARNING
Observe the following precautions. Failure to do so may result in death or serious injury.
■Closing the windows
●The driver is responsible for all the power window operations, including the operation for the passengers. In
order to prevent accidental operation, especially by a child, do not let a child operate the power windows. It is possi-
ble for children and other passengers to have body parts caught in the power window. Also, when riding with a child,
it is recommended to use the window lock switch. ( P.152)
●Check to make sure that all passen- gers do not have any part of their body
in a position where it could be caught when a window is being operated.
●When using the wireless remote con-trol or mechanical key and operating
the power windows, operate the power window after checking to make sure that there is no possibility of any
passenger having any of their body parts caught in the window. Also do not let a child operate window by the
wireless remote control or mechanical key. It is possible for children and other
passengers to get caught in the power window.
●When exiting the vehicle, turn the engine switch off, carry
the key and exit the vehicle along with the child. There may be accidental operation, due to mischief, etc., that
may possibly lead to an accident.
■Jam protection function
●Never use any part of your body to
intentionally activate the jam protec- tion function.
●The jam protection function may not work if something gets jammed just
before the window is fully closed. Be careful not to get any part of your body jammed in the window.