2018 Lexus GS450h rear view mirror

5
GS450h_QG_OM30G74U_(U)
OverviewInstrument Panel
Windshield wiper and washer switch P.37
Multi-information display P.30
Headlight switch
Turn signal lever P.33
P.27
Inside lock buttons*
Trunk opener*
Hood lock release lever*
Driving position memory
switches
P.21
See P.8
See P.7
Window lock switch*
Power window switches*
Door lock switches*
Outside rear view mirror switches*
Tilt and telescopic steering
control switch
*

10
GS450h_QG_OM30G74U_(U)
OverviewRoof
Moon roof switches*
Inside rear view mirror*
“SOS” button∗ P.87
Garage door opener switches P.83
Interior light*
Vanity lights*
∗: If equipped
*: Refer to “OWNER’S MANUAL”.
Personal lights*
Personal lights*

21
GS450h_QG_OM30G74U_(U)
Driving Position Memory
■Driving position memory
■
Recording procedure
Check that the shift lever is in P.
Turn the power switch to ON mode.
Adjust the driver’s seat, steering wheel, outside rear view mirrors and HUD (head-up
display) (if equipped) to the desired positions.
While pressing the “SET” button, or within
3 seconds after the “SET” button is pressed,
press button “1”, “2” or “3” until the buzzer
sounds.
If the selected button has already been
preset, the previously recorded position
will be overwritten.
■Recall procedure
Check that the shift lever is in P.
Turn the power switch to ON mode.
Press one of the buttons for the driving
position you want to recall until the buzzer
sounds.
This feature automatically adjusts the front seats, steering wheel and outside rear view
mirrors to make entering and exiting the vehicle easier or to suit your preferences.
1
2
3
4
1
2
3

52
GS450h_QG_OM30G74U_(U)
BSM (Blind Spot Monitor) (if equipped)
Switching the BSM function
The Blind Spot Monitor function and Rear Cross Traffic Alert function can be switched
on and off using the multi-information display.
When switched on, the BSM indicator illuminates on the meter and the buzzer sounds.
Outside rear view mirror indicators
Blind Spot Monitor function:
When a vehicle is detected in the blind spot, the outside rear view mirror indicator
comes on while the turn signal lever is not operated. If the turn signal lever is operated
toward the detected side, the outside rear view mirror indicator flashes.
Rear Cross Traffic Alert function:
When a vehicle approaching from the right or left rear of the vehicle is detected, the
outside rear view mirror indicators flash.
Rear Cross Traffic Alert buzzer (Rear Cross Traffic Alert function only)
When a vehicle approaching from the right or left rear of the vehicle is detected, a
buzzer sounds from behind the rear seat.
The Blind Spot Monitor is a system that has 2 functions;
●The Blind Spot Monitor function
Assists the driver in making the decision when changing lanes
●The Rear Cross Traffic Alert function
Assists the driver when backing up
These functions use same sensors.
1
2
3

84
GS450h_QG_OM30G74U_(U)
■Programming HomeLink®
Steps through must be performed within 60 seconds, otherwise the indicator
light will stop flashing and programming will not be able to be completed.
Press and release the HomeLink
® button you want to program and check that the
HomeLink
® indicator light flashes (orange).
Point the remote control transmitter
for the device at the rear view mirror,
1 to 3 in. (25 to 75 mm) from the
HomeLink
® buttons.
Keep the HomeLink
® indicator light
in view while programming.
Program a device.
Programming a device other than an entry gate (for U.S.A. owners)
Press and hold the remote control transmitter button until the HomeLink
® indicator light
changes from slowly flashing orange to rapidly flashing green (rolling code) or continu-
ously lit green (fixed code), then release the button.
Programming an entry gate (for U.S.A. owners)/Programming a device in the Cana-
dian market
Press and release the remote control transmitter button at 2 second intervals, repeat-
edly, until the HomeLink
® indicator light changes from slowly flashing (orange) to rapidly
flashing (green) (rolling code) or continuously lit (green) (fixed code).
Test the HomeLink
® operation by pressing the newly programmed button and observ-
ing the indicator light:
●Indicator light illuminates: Programming of a fixed code device has completed. The
garage door or other device should operate when a HomeLink
® button is pressed
and released.
●Indicator light flashes rapidly: The garage door opener motor or other device is
equipped with a rolling code. To complete programming, firmly press and hold the
HomeLink
® button for 2 seconds then release it.
●If the garage door or other device does not operate, proceed to “Programming a
rolling code system”.
13
1
2
3
4

94
What to do if...
GS450h_QG_OM30G74U_(U)
Follow the correction procedures.
Low fuel level warning lightMaster warning light
Seat belt reminder light
(Illuminates
without
blinking)Tire pressure warning light*3
See the OWNER’S MANUAL
Turn signal indicatorVSC OFF indicator
Headlight indicator (U.S.A.)PCS warning light*2
Tail light indicator (Canada)
BSM (Blind Spot Monitor)
outside rear view mirror indi-
cators
*2
Headlight high beam indicatorBSM (Blind Spot Monitor)
indicator
*2
Automatic High Beam
indicator
*2Brake hold standby indicator
Cruise control indicatorBrake hold operated
indicator
Dynamic radar cruise control
indicator
*2Low outside temperature
indicator
Cruise control “SET” indicator“READY” indicator
LKA indicator*2EV indicator
Intuitive parking assist
indicator
*2, 4(U.S.A.)Parking brake
indicator
“AFS OFF” indicator*2(Canada)
(Flashes)
Slip indicator“AIR BAG ON/
OFF” indicator
For further information, refer to the OWNER’S MANUAL.