2018 Lexus GS450h display

18
GS450h_QG_OM30G74U_(U)
■Side display
Vehicle information can be displayed on the side display (→P.57), then select or to
select the desired screen.
●Fuel consumption
●Past record
●Trip information
●Energy monitor
The image is an example only, and may vary slightly from actual conditions.

21
GS450h_QG_OM30G74U_(U)
Driving Position Memory
■Driving position memory
■
Recording procedure
Check that the shift lever is in P.
Turn the power switch to ON mode.
Adjust the driver’s seat, steering wheel, outside rear view mirrors and HUD (head-up
display) (if equipped) to the desired positions.
While pressing the “SET” button, or within
3 seconds after the “SET” button is pressed,
press button “1”, “2” or “3” until the buzzer
sounds.
If the selected button has already been
preset, the previously recorded position
will be overwritten.
■Recall procedure
Check that the shift lever is in P.
Turn the power switch to ON mode.
Press one of the buttons for the driving
position you want to recall until the buzzer
sounds.
This feature automatically adjusts the front seats, steering wheel and outside rear view
mirrors to make entering and exiting the vehicle easier or to suit your preferences.
1
2
3
4
1
2
3

23
GS450h_QG_OM30G74U_(U)
Power (Ignition) Switch
■Starting the hybrid system
Press the parking brake switch to
check that the parking brake is set.
(→P. 28)
Parking brake indicator will come on.
Check that the shift lever is in P.
Firmly depress the brake pedal.
will be displayed on the multi-
information display. If it is not dis-
played, the hybrid system cannot be
started.
Press the power switch shortly and
firmly.
When operating the power switch,
one short, firm press is enough.
It is not necessary to press and hold
the switch.
If the “READY” indicator turns on, the
hybrid system will operate normally.
Continue depressing the brake pedal
until the “READY” indicator is illumi-
nated.
The hybrid system can be started
from any power switch mode.
Check that the “READY” indicator is
illuminated.
The vehicle will not move when the
“READY” indicator is off.
Performing the following operations when carrying the electronic key on your person
starts the hybrid system or changes power switch modes.
1
2
3
4
5

24
GS450h_QG_OM30G74U_(U)
■Stopping the hybrid system
Stop the vehicle completely.
Set the parking brake (→P. 28), and shift the shift lever to P.
Press the power switch.
Release the brake pedal and check that “POWER ON” on the multi-information dis-
play is off.
■Changing power switch modes
Modes can be changed by pressing the power switch with brake pedal released. (The mode
changes each time the switch is pressed.)
Off
*
The emergency flashers can be used.
“POWER ON” will not be displayed on
the multi-information display.
ACCESSORY mode
Some electrical components such as the
audio system can be used.
“POWER ON” will be displayed on the
multi-information display.
ON mode
All electrical components can be used.
“POWER ON” will be displayed on the
multi-information display.
*: If the shift lever is in a position other than
P when turning off the hybrid system, the
power switch will be turned to ACCES-
SORY mode, not to off.
1
2
3
4

26
GS450h_QG_OM30G74U_(U)
EV Drive Mode
Turns EV drive mode on/off
When EV drive mode is turned on, “EV
MODE” will be displayed on the multi-
information display. Pressing the switch
when in EV drive mode will return the
vehicle to normal driving (using the gas-
oline engine and electric motor [traction
motor]).
In EV drive mode, electric power is supplied by the hybrid battery (traction battery), and
only the electric motor (traction motor) is used to drive the vehicle.

30
GS450h_QG_OM30G74U_(U)
Multi-information Display
■Display content
Drive information
Select to display various drive data.
Navigation system-linked display
Select to display the following navigation system-linked information.
• Route guidance
• Compass display (north-up display/heading-up display)
Audio system-linked display
Select to enable selection of an audio source or track on the display using the
meter control switches.
Driving assist information
Select to display the cruise control or dynamic radar cruise control with full-
speed range/LKA (Lane-Keeping Assist) (if equipped) information, when the
system is used. (→P. 41, 42, 47)
Warning message display
Select to display warning messages and measures to be taken if a malfunction
is detected.
Settings display
Select to change the meter display settings.
The multi-information display presents the driver with a variety of vehicle data.

31
GS450h_QG_OM30G74U_(U)
■Operating the meter control switches
The multi-information display is oper-
ated using the meter control switches.
:Switch menu
:Change displayed content,
scroll up/down the screen
and move the cursor up/
down
Press: Enter/Set
Press and hold: Reset
Return to the previous screen
Press: Displays the screen registered
to
When no screen has been registered,
the drive information screen will be dis-
played.
Press and hold: Registers the currently
displayed screen to
When the confirmation screen is dis-
played, select yes to register the
screen. If the selected screen cannot
be registered, a registration failure
message will be shown.1
2
3
4
If a problem is detected in any of the vehicle’s systems, a warning message is shown on the
multi-information display.

32
GS450h_QG_OM30G74U_(U)
Head-up Display (if equipped)
Head-up display
“HUD” button
Display brightness adjustment switch
Display position adjustment switch
“DISP” button
■Head-up display contents
●Vehicle speed
●Hybrid System Indicator
●Tachometer
●Shift position and shift range
●Audio display
*
●Route guidance display
●Lexus Enform (if equipped)
●Lane departure warning display (LKA [Lane-Keeping Assist]) (if equipped)
●Approach warning display (dynamic radar cruise control with full-speed range) (if
equipped)
●Pre-collision warning message (PCS [Pre-Collision System]) (if equipped)
●Speed limit display
*: The default setting is off
The head-up display can be used to project vehicle speed and other information onto the
windshield.
1
2
3
4
5