2018 KIA STONIC ABS

SymbolFuse rat‐ingCircuit Protected
10ABCM (Body Control Module), Crash Pad Switch, FCA Unit, Lane Departure Warning System, BLIND-
SPOT DETECTION WARNING Radar LH/RH
15AEngine Room Junction Block(Back-Up Lamp Switch), Sport Mode Switch, Speed Sensor, Stop Lamp
Switch, Speed Sensor (In/Out), Transaxle Range Switch
LH25A Power Window Main Switch, Passenger Power Window Switch(RHD)
SPARE25A Spare
10A Rear Fog Lamp Relay
15A Clock Spring
LH7.5A Head Lamp LH, License Lamp LH(Sedan), Rear Combination Lamp (IN) LH(Wagon)
7.5A Front Console Switch, Front Seat Warmer Control Module, Audio, Audio / Video & Navigation Head
Unit, Head Lamp Leveling Device Actuator LH/RH, Air Conditioner Control Module, Electro Chromic
Mirror, Crash Pad Switch, DC-DC Converter, Clock Spring, A/T Shift Lever Indicator
7.5A
Engine Room Junction Block(Multipurpose Check Connector), ABS/ESC (Electronic Stability Control)
Control Module
10A Smart Key Control Module, Stop Lamp Switch
SPARE15A Spare
15A Front Fog Lamp Relay
7.5AEngine Room Junction Block(Air Conditioner Blower Relay), GSL Junction Block(PTC Heater Relay),
DSL Junction Block(Start Relay, Air Conditioner Blower Relay), Air Conditioner Control Module
MODULE510AEngine Room Junction Block(Head Lamp High Relay, Head Lamp Relay), Front Seat Warmer Control
Module, BCM (Body Control Module)


8-85
8
Maintenance

Engine room compartment fuse panel (Kappa 1.0L T-GDI Engine (Gasoline))
SymbolFuse ratingCircuit Protected
80A MDPS Unit
ALT150A Fuse - RR DEFOG, ABS1, ABS2, BLOWER
40A Rear Defogger Relay
140A ABS/ESC (Electronic Stability Control) Control
40A ABS/ESC (Electronic Stability Control) Control, Multipurpose Check Connector
40A Air Conditioner Blower Relay
10A Wiper Motor, Multifunction Switch, Wiper LO Relay
10A Cooling Fan Relay
10A Oxygen Sensor (Up), Oxygen Sensor (Down), RCV Control Solenoid Valve
15AECM (Engine Control Module), Oil Control Valve #1, #2, Purge Control Solenoid Valve, Air Condi‐
tioner Clutch Type ECV Relay
10A Head Lamp RH
10A Head Lamp LH
E315A ECM (Engine Control Module)
E415A ECM (Engine Control Module)


8-91
8
Maintenance

Engine room compartment fuse panel
(Kappa 1.2L MPI Engine (Gasoline))
SymbolFuse ratingCircuit Protected
80A MDPS Unit
ALT150A 125AFuse - RR DEFOG, ABS1, ABS2, BLOWER
40A Rear Defogger Relay
140A ABS/ESC (Electronic Stability Control) Control
40A ABS/ESC (Electronic Stability Control) Control, Multipurpose Check Connector
40A Air Conditioner Blower Relay
10A Wiper Motor, Multifunction Switch, Wiper LO Relay
10A Cooling Fan1 Relay, Cooling Fan2 Relay
10A Oxygen Sensor (Up), Oxygen Sensor (Down), Front Wheel Sensor RH, Engine Coolant Stop Valve
15AECM (Engine Control Module), Oil Control Valve #1, #2, Purge Control Solenoid Valve, Air Condi‐
tioner Clutch Type ECV Relay
10A Head Lamp RH
10A Head Lamp LH
IGN
COIL20A Ignition Coil #1~#4, Condenser
INJECTOR15A Fuel Pump Relay, ECM, Injector #1~#4
Maintenance
8-94

Engine room compartment fuse panel
(Kappa 1.4L MPI Engine (Gasoline))
SymbolFuse ratingCircuit Protected
80A MDPS Unit
ALT150A 125AFuse - RR DEFOG, ABS1, ABS2, BLOWER
40A Rear Defogger Relay
140A ABS/ESC (Electronic Stability Control) Control
40A ABS/ESC (Electronic Stability Control) Control, Multipurpose Check Connector
40A Air Conditioner Blower Relay
10A Wiper Motor, Multifunction Switch, Wiper LO Relay
10A Cooling Fan1 Relay, Cooling Fan2 Relay
10AOxygen Sensor (Up), Oxygen Sensor (Down), Front Wheel Sensor RH, Engine Coolant Stop Valve
(M/T), Variable Intake Solenoid Valve (M/T)
15AECM/PCM, Engine Coolant Stop Valve (A/T), Oil Control Valve #1, #2 (M/T), Variable Intake Sole‐
noid Valve (A/T), Purge Control Solenoid Valve (M/T), A/C Blower Relay
10A Head Lamp RH
10A Head Lamp LH
IGN
COIL20A Ignition Coil #1~#4, Condenser

8-97
8
Maintenance

SymbolRelay NameType
A/C Blower RelayMICRO
Engine room compartment fuse panel
(U-II 1.4L/1.6L Engine (Diesel))
SymbolFuse ratingCircuit Protected
80A MDPS Unit
ALT150A Fuse - RR DEFOG, ABS1, ABS2, BLOWER
40A Rear Defogger Relay
140A ABS/ESC (Electronic Stability Control) Control
40A ABS/ESC (Electronic Stability Control) Control, Multipurpose Check Connector
40A Air Conditioner Blower Relay
10A Wiper Motor, Multifunction Switch, Wiper LO Relay
10A PM Sensor, Electronic VGT Actuator, WGT Vacuum Modulator
10A Lambda Sensor #1, #2, Rail Pressure Regulating Valve, Cooling Fan1 Relay, Cooling Fan2 Relay
15A Camshaft Position Sensor, Air Flow Sensor, Oil Control Valve, PTC1 Heater Relay
10A Head Lamp RH
10A Head Lamp LH
Maintenance
8-100

Side repeater lamp (bulb type)
bulb Replacement
1. Remove the lamp assembly fromthe vehicle by prying the lens and
pulling the assembly out.
2. Disconnect the bulb electrical con‐ nector.
3. Separate the socket and the lens parts by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
lens part.
4. Remove the bulb by pulling it straight out.
5. Insert a new bulb in the socket. 6. Reassemble the socket and the
lens part.
7. Connect the bulb electrical connec‐ tor.
8. Reinstall the lamp assembly to the body of the vehicle.
Headlamp (Low/High beam) bulb
replacement (Headlamp Type A)
0:##
1. Open the hood.
2. Remove the headlamp bulb coverby turning it counterclockwise.
3. Disconnect the headlamp bulb socket-connector. 4. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
5. Install a new bulb-socket assembly in the headlamp assembly by align‐
ing the tabs on the bulb-socket
with the slots in the headlamp as‐
sembly. Push the bulb-socket into
the headlamp assembly and turn
the bulb-socket clockwise.
6. Install the headlamp bulb cover by turning it clockwise.
Headlamp bulb

8-109
8
Maintenance

WARNING
nHalogen bulbs
•Halogen bulbs contain pressurizedgas that will produce flying piecesof glass if broken.
•Always handle them carefully, andavoid scratches and abrasions. Ifthe bulbs are lit, avoid contactwith liquids. Never touch the glasswith bare hands. Residual oil maycause the bulb to overheat andburst when lit.A bulb should be operated onlywhen installed in a headlight.
•If a bulb becomes damaged orcracked, replace it immediatelyand carefully dispose of it.
•Wear eye protection when chang‐ing a bulb. Allow the bulb to cooldown before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type A)
0:##
1. Open the hood.
2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket. 4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Position lamp / Day time
running lamp bulb replacement
(Headlamp Type A)
0:##
1. Open the hood.
Maintenance
8-110

2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket.
4. Insert a new bulb by inserting it in‐ to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.Headlamp (Low/High beam) bulb
replacement (Headlamp Type B)
0:##
1. Open the hood.
2. Remove the headlamp bulb cover by turning it counterclockwise.
3. Disconnect the headlamp bulb socket-connector.
4. Remove the bulb-socket from the headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly. 5. Install a new bulb-socket assembly
in the headlamp assembly by align‐
ing the tabs on the bulb-socket
with the slots in the headlamp as‐
sembly. Push the bulb-socket into
the headlamp assembly and turn
the bulb-socket clockwise.
6. Install the headlamp bulb cover by turning it clockwise.
Headlamp bulb

8-111
8
Maintenance