2018 KIA SPORTAGE sensor

*IF EQUIPPED 9ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
DRIVER'S PANEL
For more information on the BSD System, refer to your Owner’s Manual.
Blind Spot Detection (BSD) System*
The BSD system uses radar sensors to help alert the driver before changing
lanes . The light on the BSD button A will illuminate when turned ON . The outside
rearview mirror warning lights will also illuminate for 3 seconds .
The system will become active when the vehicle is traveling more than 20 mph
and will alert the driver if another vehicle is detected by the radar sensor, up to
230 feet away .
REMINDERS:
•When the BSD is ON and the vehicle power is cycled to OFF then ON again, the BSD system returns to ON
•
The RCTA feature can be turned OFF/ON in User Settings
Blind Spot Detection System Video
To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
www.youtube.com/KiaFeatureVideosRCTA (Rear Cross Traffic Alert)
If the RCTA system sensors detect approaching vehicles from the left or right
side C, the system will sound an audible alert, the warning indicators on the
outside rearview mirror will illuminate and a message will appear on the LCD
screen, with these conditions:
•When the gear shift is in Reverse
•When the vehicle moves in reverse from a parked position
•When the vehicle is moving less than 6 mph
QR CODE
Blind Spot Detection (BSD)* / Lane Change Assist (LCA)*
1st-stage alert: When another vehicle is detected within the BSD System boundary B, a yellow indicator will illuminate on the outside rearview mirrors .
2nd-stage alert: When 1st-stage alert is on and the driver activates a turn signal,
a flashing yellow indicator will illuminate on the outside rearview mirrors and the
system will sound an alert .
B
A
C

DRIVER'S PANEL
10*IF EQUIPPED SPORTAGE FEATURES & FUNCTIONS GUIDE
Electronic Stability Control (ESC)
The ESC system is designed to help stabilize the vehicle
during cornering maneuvers . It is a good idea to keep
the ESC turned ON for daily driving whenever possible .
Press ESC button B to turn ESC OFF/ON .
REMINDERS:
•
ESC is turned ON by default at vehicle start-up . When ignition is cycled, ESC will turn ON again
•
The ESC Indicator Light in the instrument cluster will illuminate whenever the ESC is in operation
Lane Departure Warning System (LDWS)*
AC
B
Lane Departure Warning System Video
To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
www.youtube.com/KiaFeatureVideos
QR CODE
With the Engine Start /Stop button in the ON position, press the
LDWS button C to turn system ON . The instrument cluster
indicator will illuminate green .
If the LDWS detects that you are veering outside of your lane, the
system may issue a warning on the LCD screen and an alert may
sound, under these conditions:
• The vehicle exceeds approximately 37 mph
• The LDWS system recognizes the lane the vehicle is traveling in
If the LDWS button is ON and ignition is cycled, the system will
turn ON again . If the LDWS button is OFF, the system remains OFF .
REMINDER:
LDWS will not issue a warning if the turn signal is activated
Lane Departure
Lane Departure
Lane Departure
Lane Departure
The Lane Departure Warning System (LDWS) is not a substitute for safe and proper driving. Always drive safely and use caution. LDWS may not always alert the driver if the vehicle is driven outside of its lane.
(Buttons located on left of Steering Wheel)
Instrument Panel Dimmer
With parking lights/headlights ON, toggle switch A up (+) or down (-) to adjust the brightness of the
instrument panel illumination .
REMINDER: The Instrument Panel Dimmer does not adjust brightness on the audio/navigation system* screens; use SETUP to adjust brightness on the screens .
When the LDWS sensor does not detect the lane traveling in the lanes are not illuminated
When the LDWS sensor detects the vehicle veering outside of the lane traveling in, a yellow indicator will illuminate either on the left or right lane (shown in both images above)
When the LDWS sensor detects the lane traveling in, both lanes are illuminated
Lane Departure
Lane Departure
Lane Departure
Lane Departure
For more information on Electronic Stability Control (ESC) and its specific features and operations, please refer to your Owner’s Manual.

*IF EQUIPPED SPORTAGE FEATURES & FUNCTIONS GUIDE
STEERING WHEEL CONTROLS
16
PUSH
PULL
PUSH
PULL
QUIC K T IP
PUSH
PULL
PUSH
PULL
QUIC K T IP
To o p e r a t e :
•Move lever Up/Down to change
Wiper modes
•Press INT switch A up/down to
adjust Intermittent Wipe Speed
•Pull lever to spray and wipe
Windshield Wipers & Washers
Rear Wiper & Washer
To operate:
•Rotate Rear Wiper switch
to change Wiper modes
•Push lever to spray and wipe
Auto Control (Rain Sensing)*
The rain sensor located on the upper end of the windshield glass senses the amount of
rainfall and controls the wiping cycle for the proper interval .The more it rains, the faster the
wiper operates .When the rain stops, the wiper stops .
To adjust the Auto Rain Sensing speed setting, move the speed control switch A up/down .
B
A
D
C
To adjust the Steering Wheel, press the lock-
release lever B down and adjust to the desired
angle C and then the distance D .
When finished, pull the lock-release lever B up to
lock Steering Wheel in place .
Tilt/Telescoping Steering Wheel
LO and HI sets wiper speed . No intermittent wipe function is available on rear wipers .
QUICK TIP
Moving switch A up increases intermittent wipe frequency and wipe speed . Moving switch A down decreases frequency of wipes .
QUICK TIP M I S T: Single wipeOFF: Wiper offINT/AUTO*: Intermittent Wipe/Rain Sensing*LO: Slow wipeHI: Fast wipe
HI: Fast wipeLO: Slow wipeOFF: Wiper off

36*IF EQUIPPED SPORTAGE FEATURES & FUNCTIONS GUIDE
OTHER KEY FEATURES
HomeLink® with Auto-Dimming
Rearview Mirror*
A HomeLink® button
B HomeLink® button
C Indicator light
D HomeLink® button
E Glare detection sensor
F Automatic dimming ON
G Automatic dimming OFF
ABCDEFG
REMINDER: Mirror indicator light C will illuminate when automatic dimming is ON .
The HomeLink®/Auto-Dimming Rearview Mirror* is designed to
reduce glare from a vehicle’s headlights located in the rear and also
connect up to three electronic transmitters into one location .
•
To turn automatic dimming ON, press button F
•
To turn automatic dimming OFF, press button G
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515.
How to Sync Transmitter with HomeLink®*
If programming for the first time, begin with Step 1 (repeating this step will
delete all information) .
To program non-rolling and rolling code garage door openers and other
devices:
1 . Press and hold the left A and center D buttons simultaneously until the
indicator light C begins to flash (to reprogram buttons, skip this step)
2 . Press and hold the desired button A, B or D and hold the button on the
transmitter while it is approximately 1 to 3 inches away from the mirror .
The HomeLink® Indicator light C will flash rapidly once the frequency
signal has been successfully programmed
To finish programming rolling code garage door openers, complete these
steps:
3 .
Locate the “learn” or “smart” button on the garage door’s motor head unit .
Press and release the button and complete Step 4 within 30 seconds .
4 . Firmly press and release the programmed HomeLink® button up to three
times .
• You can reprogram a single HomeLink® button by repeating Step 2• Erasing programmed buttons will delete all trained transmitters
QUICK TIP
Operating HomeLink®:
Press one of the programmed HomeLink® buttons .
Erasing programmed buttons:
Press and hold the left A and center D buttons simultaneously for
approximately 20 seconds, and then release both buttons within 30 seconds .