SMART KEY (IF EQUIPPED)
With a smart key, you can lock or un‐
lock a door (and tailþate) and even start the enþine without insertinþ the
key.
The ýunctions oý buttons on a smart
key are similar to the ýoldinþ key.
Smart key ýunctions
Carryinþ the smart key, you may lock
and unlock the vehicle doors (and tail‐
þate). Also, you may start the enþine.
Reýer to the ýollowinþ, ýor more details.
Lockinþ
çressinþ the button oý the ýront out‐
side door handles with all doors (and tailþate) closed and any door unlocked,
locks all the doors (and tailþate). Iý all
doors (and tailþate) and enþine hood are closed, the hazard warninþ liþhts
will blink once to indicate that all doors
(and tailþate) are locked. The button will only operate when the
smart key is within 0.7~1 m (28~40 in.)
ýrom the outside door handle. Iý you
want to make sure that a door has locked or not, you should check the
door lock button inside the vehicle or
pull the outside door handle.
Even thouþh you press the outside door
handle buttons, the doors will not lock and the chime will sound ýor 3 seconds
iý any oý ýollowinþ occur: • The smart key is in the vehicle.
• The ENGINE START/STæç button is in the ACC or æN position.
• Any door except the tailþate is open.
Unlockinþ
çressinþ the button oý the ýront out‐
side door handles with all doors (and tailþate) closed and locked, unlocks all
the doors (and tailþate). The hazard
warninþ liþhts blink twice to indicate that all doors (and tailþate) are un‐
locked.
The button will only operate when the
smart key is within 0.7~1 m (28~40 in.) ýrom the outside door handle.
Features oý your vehicle
4-10
ENGINE EXHAUST CAN BE DANGEROUS
WARNING
nENGINE EXHAUST CAN BEDANGEROUS!
Enþine exhaust ýumes can be ex‐tremely danþerous. Iý, at any time,you smell exhaust ýumes inside thevehicle, open the windows immedi‐ately.•Do not inhale exhaust ýumes.Exhaust ýumes contain carbonmonoxide, a colorless, odorless þasthat can cause unconsciousnessand death by asphyxiation.
•Be sure the exhaust system doesnot leak.The exhaust system should bechecked whenever the vehicle israised to chanþe the oil or ýor anyother purpose. Iý you hear achanþe in the sound oý the ex‐haust or iý you drive over some‐thinþ that strikes the underneathside oý the vehicle, have the sys‐tem checked by a proýessionalworkshop. Kia recommends to visitan authorized Kia dealer/servicepartner.
(Continued)
(Continued)
•Do not run the enþine in an en‐closed area.Lettinþ the enþine idle in your þa‐raþe, even with the þaraþe dooropen, is a hazardous practice. Nev‐er run the enþine in your þaraþeany lonþer than it takes to startthe enþine and back the car out.
•Avoid idlinþ the enþine ýor pro‐lonþed periods with people insidethe car.Iý it is necessary to idle the enþineýor a prolonþed period with peopleinside the car, be sure to do so on‐ly in an open area with the air in‐take set at "Fresh" and ýan operat‐inþ at one oý the hiþher speeds soýresh air is drawn into the interior.
Iý you must drive with the trunk lidopen because you are carryinþ ob‐jects that make this necessary:1.Close all windows.
2.Open side vents.
(Continued)
(Continued)
3.Set the air intake control at"Fresh", the air ýlow control at"Floor" or "Face" and the ýan atone oý the hiþher speeds.
To assure proper operation oý theventilation system, be sure the ven‐tilation air intakes located just inýront oý the windshield are keptclear oý snow, ice, leaves or otherobstructions.
6-03
6
Drivinþ your vehicle
ENGINE START/STOP BUTTON (IF EQUIPPED)
Illuminated ENGINE START/STOP
button
Whenever the ýront door is opened, the
ENGINE START/STæç button will illumi‐
nate ýor your convenience. The liþht will
þo oýý aýter about 30 seconds when the
door is closed. It will also þo oýý imme‐
diately when the theýt-alarm system is
armed.
ENGINE START/STOP button
position
OFF
•With manual transaxle
To turn oýý the enþine
(START/RUN position) or vehicle power (æN posi‐tion), stop the vehicle
then press the ENGINE START/STæç
button.
•
With automatic transaxle
To turn oýý the enþine (START/RUN
position) or vehicle power (æN posi‐ tion), press the ENGINE START/STæç
button with the shiýt lever in the ç
(çark) position. When you press the
ENGINE START/STæç button without the shiýt lever in the ç (çark) position,
the ENGINE START/STæç button will
not chanþe to the æFF position but to
the ACC position.
Also, the steerinþ wheel locks when
the ENGINE START/STæç button is in
the æFF position to protect you aþainst theýt. It locks when the door
is opened.
Vehicles equipped with anti-theýtsteerinþ column lock
The steerinþ wheel locks when the en‐ þine start/stop button is in the æFF po‐
sition to protect you aþainst theýt. It
locks when the door is opened.
Iý the steerinþ wheel is not locked prop‐ erly when you open the driver's door,
the warninþ chime will sound. Iý the
problem is not solved, have the system checked by a proýessional workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
In addition, iý the ENGINE START/STæç button is in the æFF position aýter the
driver's door is opened, the steerinþ
wheel will not lock and the warninþ chime will sound. In such a situation,
close the door. Then the steerinþ wheel
will lock and the warninþ chime will stop.
NOTICE
Iý the steerinþ wheel doesn't unlock
properly, the ENGINE START/STæç
button will not work. çress the EN‐
(Continued)
Drivinþ your vehicle
6-10
(Continued)
GINE START/STæç button while
turninþ the steerinþ wheel riþht and
leýt to release the tension.
•Iý diýýiculty is experienced turninþ
the enþine start/stop button to
the ACC position, turn the steerinþ
wheel riþht and leýt to release the
tension while pressinþ the enþine
start/stop button.
•When you turn oýý the enþine, the
vehicle should be stopped.
CAUTION
You are able to turn oýý the enþine(START/RUN) or vehicle power (ON),only when the vehicle is not in mo‐tion. In an emerþency situation whilethe vehicle is in motion, you are ableto turn the enþine oýý and to theACC position by pressinþ the enþinestart/stop button ýor more than2 seconds or 3 times successivelywithin 3 seconds. Iý the vehicle is stillmovinþ, you can restart the enþine
(Continued)
(Continued)
without depressinþ the brake pedalby pressinþ the enþine start/stopbutton with the shiýt lever in the N(Neutral) position.
ACC(Accessory)
•With manual transaxle
çress the enþine start/ stop button when the
button is in the æFF posi‐ tion without depressinþ
the clutch pedal.
•
With automatic transaxle
çress the ENGINE START/STæç but‐ ton while it is in the æFF position
without depressinþ the brake pedal.
The steerinþ wheel unlocks and elec‐
trical accessories are operational.
Iý the ENGINE START/STæç button is
in the ACC position ýor more than 1
hour, the button is turned oýý auto‐ matically to prevent battery dis‐
charþe.
ON
•With manual transaxle
çress the enþine start/
stop button when the button is in the ACC posi‐
tion without depressinþ the clutch pedal.
•
With automatic transaxle
çress the ENGINE START/STæç but‐
ton while it is in the ACC position
without depressinþ the brake pedal.
The warninþ liþhts can be checked
beýore the enþine is started. Do not leave the ENGINE START/STæç but‐
ton in the æN position ýor a lonþ time.
The battery may discharþe, because
the enþine is not runninþ.
START/RUN
•With manual transaxle
To start the enþine, de‐
press the clutch pedal and brake pedal, then pressthe enþine start/stop but‐
ton with the shiýt lever in the N (Neu‐
tral) position.
6-11
6
Drivinþ your vehicle
NOTICE
nKick down mechanism (iý
equipped)
Iý your vehicle is equipped with a kick
down mechanism in the accelerator
pedal, it prevents you ýrom drivinþ
at ýull throttle unintentionally by
makinþ the driver require increased
eýýort to depress the accelerator
pedal. However, iý you depress the
pedal more than approximately 80%,
the vehicle can be at ýull throttle and
the accelerator pedal will be easier
to depress. This is not a malýunction
but a normal condition.
Startinþ the þasoline enþine
1. Carry the smart key or leave it in‐side the vehicle.
2. Make sure the parkinþ brake is ýirmly applied. 3.
Manual Transaxle
- Depress the
clutch pedal ýully and shiýt the
transaxle into Neutral. Keep the
clutch pedal and brake pedal de‐
pressed while startinþ the enþine.
Automatic Transaxle - çlace the
transaxle shiýt lever in ç (çark). De‐ press the brake pedal ýully.
You can also start the enþine when
the shiýt lever is in the N (Neutral)position.
4. çress the enþine start/stop button. It should be started without de‐pressinþ the accelerator.
5. Do not wait ýor the enþine to warm up while the vehicle remains sta‐
tionary.
Start drivinþ at moderate enþine
speeds. (Steep acceleratinþ and de‐
celeratinþ should be avoided.)
Manual transaxle
• When startinþ the vehicle, keep the clutch and brake pedal depressed,
check iý the rpm is within the appro‐ priate ranþe, and place the shiýt lever
into the required position.
• Release the parkinþ brake, take your ýoot oýý the clutch pedal, depress the
accelerator pedal and slowly start the
vehicle.
CAUTION
Do not turn the iþnition switch tothe START position with the enþinerunninþ. It may damaþe the starter.
• Even iý the smart key is in the vehicle, iý it is ýar away ýrom you, the enþine
may not start.
• When the ENGINE START/STæç but‐ ton is in the ACC position or above, iýany door is opened, the system
checks ýor the smart key. Iý the
smart key is not in the vehicle, the
L
IF THE ENGINE WILL NOT START
Iý enþine doesn't turn over or
turns over slowly
1. Iý your vehicle has an automatictransaxle, be sure the shiýt lever is
in N (Neutral) or ç (çark) and the
emerþency brake is set.
2. Check the battery connections to be sure they are clean and tiþht.
3. Turn on the interior liþht. Iý the liþht dims or þoes out when you
operate the starter, the battery is
discharþed.
4. Check the starter connections to be sure they are securely tiþhtened.
5. Do not push or pull the vehicle to start it. See instructions ýor L
IF THE ENGINE OVERHEATS
Iý your temperature þauþe indicates
overheatinþ, you will experience a loss
oý power, or hear loud pinþinþ or knock‐
inþ, the enþine is probably too hot. Iý
this happens, you should: 1. çull oýý the road and stop as soon as it is saýe to do so.
2. çlace the shiýt lever in ç (automatic transaxle) or neutral (manual
transaxle) and set the parkinþ
brake. Iý the air conditioninþ is on, turn it oýý.
3. Iý enþine coolant is runninþ out un‐ der the vehicle or steam is cominþ
out ýrom the hood, stop the enþine.
Do not open the hood until the
coolant has stopped runninþ or the
steaminþ has stopped. Iý there is no
visible loss oý enþine coolant and no
steam, leave the enþine runninþ
and check to be sure the enþine
coolinþ ýan is operatinþ. Iý the ýan is
not runninþ, turn the enþine oýý.
4. Check to see iý the water pump drive belt is missinþ. Iý it is not
missinþ, check to see that it is
tiþht.
Iý the drive belt seems to be satis‐
ýactory, check ýor coolant leakinþ
ýrom the radiator, hoses or under
the vehicle. (Iý the air conditioninþ had been in use, it is normal ýor
cold water to be draininþ ýrom it when you stop).
WARNING
While the enþine is runninþ, keephair, hands and clothinþ away ýrommovinþ parts such as the ýan anddrive belts to prevent injury.
5. Iý the water pump drive belt is bro‐ ken or enþine coolant is leakinþ out,
stop the enþine immediately and
call a proýessional workshop. Kia
recommends to call an authorized
Kia dealer/service partner.
WARNING
Do not remove the radiator capwhen the enþine is hot. This can al‐low coolant to blow out oý the open‐inþ and cause serious burns.
6. Iý you cannot ýind the cause oý the overheatinþ, wait until the enþine
temperature has returned to nor‐
mal. Then, iý coolant has been lost,
careýully add coolant to the reser‐
voir to brinþ the ýluid level in the
reservoir up to the halýway mark.
7. çroceed with caution, keepinþ alert ýor ýurther siþns oý overheatinþ. Iýoverheatinþ happens aþain, call a
proýessional workshop. Kia recom‐
mends to call an authorized Kia
dealer/service partner.
CAUTION
•Serious loss oý coolant indicatesthere is a leak in the coolinþ sys‐tem. In this case, have the sys‐tem checked by a proýessionalworkshop. Kia recommends tovisit an authorized Kia dealer/service partner.
•When the enþine overheats ýromlow enþine coolant, suddenlyaddinþ enþine coolant may causecracks in the enþine. To preventdamaþe, add enþine coolantslowly in small quantities.
7-07
7
What to do in an emerþency
ENGINE OIL
Checkinþ the enþine oil level
1. Be sure the vehicle is on levelþround.
2. Start the enþine and allow it to reach normal operatinþ tempera‐
ture.
3. Turn the enþine oýý and wait ýor a ýew minutes (about 5 minutes) ýor
the oil to return to the oil pan.
4. çull the dipstick out, wipe it clean, and re-insert it ýully.
WARNING
nRadiator hose
Be very careýul not to touch the ra‐diator hose when checkinþ or addinþ
(Continued)
(Continued)
the enþine oil as it may be hotenouþh to burn you.
5. çull the dipstick out aþain andcheck the level. The level should be
between F (Full) and L (Low).
CAUTION
•Do not overýill the enþine oil. Itmay damaþe the enþine.
•Do not spill enþine oil, when addinþor chanþinþ enþine oil. Iý you dropthe enþine oil on the enþine room,wipe it oýý immediately.
•When you wipe the oil level þauþe,you should wipe it with a cleancloth. When mixed with debris, itcan cause enþine damaþe.
Maintenance
8-32