2018 INFINITI QX30 light

Leave the vehicle and keep a safe distance
from the vehicle until the engine has cooled
down.
Check the coolant level and top up the cool-
ant, observing the warning notes (see "If your
vehicle overheats" in the "6. In case of emer-
gency" section).
If you have to top up the coolant frequently,
have the engine cooling system checked.
Make sure that the air supply to the engine
radiator is not blocked, e. g. by frozen slush.
Do not start the engine again until the cool-
ant temperature is below 250°F (120°C). The
engine may otherwise be damaged.
Low fuel warning light
This light comes on when the fuel level in the
fuel tank is getting low. Refuel as soon as it is
convenient, preferably before the fuel gauge
reaches 0 (Empty).There will be a small re-
serve of fuel in the tank when the fuel gauge
reaches 0 (Empty).
Vehicle Dynamic Control
(VDC) warning light
The VDC warning light blinks when the Ve-
hicle Dynamic Control (VDC) system is oper-
ating, thus alerting the driver to the fact that
the road surface is slippery and the vehicle is
nearing its traction limits. You may feel or hear the system working, this
is normal.
The light will continue to blink for a few sec-
onds after the VDC system stops limiting
wheel spin.
Cruise control or Intelligent Cruise Control is
deactivated.
For additional information see " Vehicle Dy-
namic Control (VDC) OFF indicator light " in
the "2. Instruments and controls" section and
"Vehicle Dynamic Control (VDC) system" in
the "5. Starting and driving" section.
INDICATOR LIGHTS
Turn signal/hazard indicator
lights
The appropriate light flashes when the turn
signal switch is activated. Both lights flash
when the hazard switch is turned on.
Low beam indicator light
This light comes on when the switch is turned
to the position:The headlights will come
on and front side, tail, number plate and in-
strument lights remain on.
Vehicle Dynamic Control
(VDC) OFF indicator light
The light comes on when the Vehicle Dy-
namic Control (VDC) has been disabled. This
indicates that the VDC system is not operat-
ing.
Disabling the VDC system causes the For-
ward Emergency Braking system to become
unavailable. See " Forward emergency brak-
ing (FEB) system (if equipped)" in the "5.
Starting and driving" section for more details.
This light also comes on briefly when the
ignition switch is turned to the ON position.
The light will turn off after approximately 1
second if the VDC system is operational.
When the VDC OFF indicator light and VDC
warning light (see " Vehicle Dynamic Control
(VDC) warning light" later in this section)
come on with the VDC system turned on, it
alerts the driver to the fact that the system's
fail-safe mode is operating. This means that
the system may not be functioning properly.
Have the system checked. It is recommended
you visit an INFINITI retailer for these ser-
vices.
Instruments and controls2-13

If an abnormality occurs in the system, the
VDC system function will be canceled, but
the vehicle is still driveable. For additional
information, see "Vehicle Dynamic Control
(VDC) system" in the "5. Starting and driving"
section.
WARNING
VDC should remain on unless freeing a ve-
hicle from mud or snow.
While the VDC system is operating, you
might feel a slight vibration or hear the sys-
tem working when starting the vehicle or ac-
celerating, but this is normal.
Front fog light indicator light (if
equipped)
The light comes on when the front fog lights
are switched on (see " Fog light switch (If so
equipped)" later in this section).
High beam assist indicator
light (if equipped)
The indicator light illuminates when the
headlights come on while the headlight
switch is in the AUTO position with the high
beam selected. This indicates that the high
beam assist system is operational. (See
2-64.)
High beam indicator light
This blue light comes on when the headlight
high beams are on and goes out when the
low beams are selected.
The high beam indicator light also comes on
when the passing signal is activated.
Rear fog light indicator light
The light comes on when the rear fog light is
switched on (see " Fog light switch (If so
equipped)" later in this section).
Side light and headlight
indicator light
This light comes on when the side light or
headlight position is selected, see "Headlight
and turn signal switches" later in this section
for further details.
/Front passenger air
bag status light
The front passenger air bag status light () located on the center console above
the shift lever will illuminate when the front
passenger air bag is turned OFF. When the
front passenger air bag is turned on, the front
passenger air bag status light ON (
) will
illuminate.
For more details, see "Front passenger air
bag and status light" in the "1. Safety — seats,
seat belts and supplemental restraint system"
section.
AUDIBLE REMINDERS
Parking brake reminder chime
A chime will sound when driving away if the
parking brake has not been released. Stop the
vehicle and release the parking brake.
Light reminder chime
With the ignition switch placed in the OFF
position, a chime sounds when the driver's
door is opened if the side lights are on. Turn
the headlight control switch off before leav-
ing the vehicle.
Seat belt reminder chime
A chime will sound for approximately 120
seconds if the vehicle's speed exceeds 16
2-14Instruments and controls

MPH (25 km/h) and the driver's seat belt or
front passenger's seat belt, if occupied is not
securely fastened. See "Seat belt warning
light" in the "1. Safety — seats, seat belts and
supplemental restraint system" section.
Idle Stop/Start System reminder
chime (if equipped)
The engine will shift to the normal stopped
state if any of the following operations is
made during Idle Stop/Start System activa-
tion, and the Idle Stop/Start System chime
will sound if:
– The vehicle engine hood is open.When the above condition continues for over
3 minutes the Idle Stop/Start System chime
will sound in 5-minute intervals as a reminder
to prevent the possibility of a discharged bat-
tery. Use the ignition switch to turn off the
engine.
Close the hood or the driver’s door, or fasten
the seat belt then restart the engine using the
ignition switch.
For more information, see " Idle Stop/Start
System (if equipped)" in the "5. Starting and
driving" section.
The vehicle information display
1is located
between the tachometer and the
speedometer.
NIC2751
VEHICLE INFORMATION DISPLAY
Instruments and controls2-15

1Permanent display: depending on vehicle
specification: outside temperature or
speed
2Time
3Text field
4Menu bar
5Drive program
6Shift lever position
Text field
3shows the selected menu or
submenu as well as display messages.
NOTE
Set the time using the INFINITI controller
and the [Settings] menu available in the cen-
tral display (see "Clock settings" in the "4.
Display screen, heater and air conditioner,
and audio system" section).
MENUS AND SUBMENUS
To call up the menu bar4and select a menu,
press theorbutton on the steer-
ing wheel. Menu bar
4disappears after a
few seconds.
Depending on the equipment fitted in the
vehicle, you can call up the following menus:
•[Trip] menu
•[Navi] menu (navigation instructions)
•[Audio] menu
•[DriveAssist] menu
•[Serv.] menu
•[Settings] menu
The [Audio] and [Navi] menus differ slightly
in vehicles with an audio system and in ve-
hicles with a navigation system. The ex-
amples given in this Owner's Manual apply to
vehicles equipped with navigation.
[Trip] menu
Standard display:
Press and hold the
button on the steer-
ing wheel until the [Trip] menu with trip meter
1and total distance recorder2is shown.
NIC2752NIC2753
2-16Instruments and controls

Showing the distance display:
1. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Distance display].
3. Press the button. The vehicle information display shows the
Intelligent Cruise Control (ICC) distance
display in the assistance graphic.
The distance display also shows you the
status of and/or information from the fol-
lowing driving systems or driving safety
systems:
•Intelligent Cruise Control (ICC)
•Forward Emergency Braking (FEB)
•Lane Departure Warning (LDW)
•Blind Spot Warning (BSW)
•Rear window wiper
Deactivating/activating VDC:
The vehicle should be driven with the Vehicle
Dynamic Control (VDC) system on for most
driving conditions.
If the vehicle is stuck in mud or snow, the
VDC system reduces the engine output to
reduce wheel spin. The engine speed will be
reduced even if the accelerator is depressed
to the floor. If maximum engine power is
needed to free a stuck vehicle, turn the VDC
system off.
For further information about VDC, see "Ve-
hicle Dynamic Control (VDC) system" in the
"5. Starting and driving" section.
1. Start the engine.
2. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu.
3. Press the
orbutton to select
[ESP].
4. Press the button. The current selection is displayed. 5. To activate/deactivate: press the
button again.
VDC is deactivated if the
warning
light in the combination meter lights up
continuously when the engine is running.
If both the
warning light andwarning light are lit continuously, VDC is not
available due to a malfunction.
Activating/deactivating Forward Emer-
gency Braking:
1. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Emergency Brake].
3. Press the button. The current selection is displayed.
4. To activate/deactivate: press the button again.
When Forward Emergency Braking is de-
activated, the
symbol appears in the
vehicle information display in the assis-
tance graphic display.
For further information about Forward
Emergency Braking, see " Forward emer-
gency braking (FEB) system (if equipped)" in
the "5. Starting and driving" section.
NIC2729
Instruments and controls2-23

Settings menu
Depending on the equipment fitted in the
vehicle, in the [Settings] menu you have the
following options:
•Changing the instrument cluster settings.
•Changing the light setting.
•Changing the vehicle setting.
•Changing the convenience setting.
•Restoring the factory setting.
Instrument cluster:
Unit of measurement for distance: The Dis-
play unit Speed-/odometer function allows
you to choose whether certain displays ap-
pear in kilometers or miles in the vehicle infor-
mation display. 1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Display Unit Speed-/Odometer]
function.
You will see the selected setting: [miles] or
[km].
5. Press the button to change the set- ting.
The selected unit of measurement for dis-
tance applies to:
•Digital speedometer in the [Trip] menu.
•Total distance recorder and the trip meter.
•Trip computer.
•Current fuel consumption and approxi-
mate range.
•Navigation instructions in the [Navi] menu.
•Cruise control.
•Speed limiter.
•Intelligent cruise control (ICC).
•Maintenance service interval display.
Switching the additional speedometer on/
off.
The [Speedometer (mph)] or [Speedometer
(km/h)] function allows you to choose
whether the vehicle information display in the
status area shows the speed in MPH or in
km/h instead of the outside temperature.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Speedometer (mph)] or [Speedom-
eter (km/h)] function.
You will see the selected setting: [On] or
[off].
5. Press the button to change the set- ting.
Selecting the permanent display function.
You can determine whether the vehicle infor-
mation display permanently shows the out-
side temperature or the speed in MPH.
NIC2731
Instruments and controls2-25

1. Press theorbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Outside Temperature] function.
You will see the selected setting: [outside
temperature] or [Speedometer (mph)].
5. Press the button to save the setting.
Lights
Switching the Adaptive Front Lighting Sys-
tem on/off:
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm. 4. Press the
orbutton to select
the [Adaptive front lighting system] func-
tion.
If the [Adaptive front lighting system]
function has been switched on, the cone
of light and the
symbol in the vehicle
information display are shown in orange.
5. Press the button to save the setting.
When you switch the [Adaptive front lighting
system] function on, you activate the follow-
ing functions:
•Freeway mode
•Active light function
•Cornering light function
If you set the low beam headlights for driving
on the right/left, the vehicle information dis-
play shows the [Adaptive front lighting sys-
tem: System Inoperative Inactive For Left-
side Traffic] or [Adaptive front lighting
system: System Inoperative Inactive for
Right-side Traffic] display message instead
of the [Adaptive front lighting] function in the
[Light] submenu.
For further information about the Adaptive
Front Lighting system, see " Adaptive front
lighting system (LED headlight only) (if
equipped)" later in this section Setting the low beam headlights for driving
on the left/right:
This function is only available on vehicles with
the Adaptive Front Lighting System (see "
Adaptive front lighting system (LED head-
light only) (if equipped)" later in this section).
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Low-b. Headl. Setting For:] function.
You will see the selected setting: [Right-
side Traffic] or [Left-side Traffic].
5. Press the button to save the setting. If you change the setting, conversion does
not take place until the next time the ve-
hicle is stationary.
If you set the low beam headlights for driving
on the right/left, then freeway mode is un-
available. This is only deactivated if the set-
ting for driving on the left/right is set oppo-
site to your vehicle's country version.
An INFINITI retailer can set the low beam
headlights for driving on the left/right.
2-26Instruments and controls

Setting the brightness of the ambient light-
ing:
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Ambient Light Brightness] function.
You will see the selected setting.
5. Change the setting with . If you change the setting, conversion does
not take place until the next time the ve-
hicle is stationary.
6. Press the
orbutton to adjust
the brightness to a level from [Off] to
[Level 5] (bright).
7. Press the or
button to save the
setting. Activating/deactivating the surround
lighting and exterior lighting delayed
switch-off:
If you have activated the Surround lighting
function and the light switch is set to
, the following functions are acti-
vated when it is dark:
•Surround lighting: the exterior lighting re-
mains lit for 40 seconds after unlocking
with the key. If you start the engine, the
surround lighting is switched off and auto-
matic headlight mode is activated .
•Exterior lighting delayed switch-off: the
exterior lighting remains lit for 60 seconds
after the engine is switched off. If you
close all the doors and the lift gate, the
exterior lighting goes off after 15 seconds.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Surround Lighting] function.
5. Press the button to save the setting. When the [Surround Lighting] function is
activated, the light cone and the area around the vehicle are displayed in orange
in the vehicle information display
6. Press the button to confirm the set- ting.
Deactivating delayed switch-off of the exte-
rior lighting temporarily:
1. Before leaving the vehicle, switch the igni- tion switch to the OFF position.
2. Switch the ignition switch to the ON po- sition.
The exterior lighting delayed switch-off is
deactivated.
Delayed switch-off of the exterior lighting is
reactivated the next time you start the en-
gine.
Depending on your vehicle's equipment,
when the surround lighting and delayed
switch-off exterior lighting are on, the fol-
lowing light up:
•Side lights
•Fog lights
•Low beam headlights
•Daytime driving lights
•Surround lighting in the exterior mirrors
Instruments and controls2-27