2018 INFINITI QX30 warning

•If dirt builds up in the shoulder belt guide
of the seat belt anchors, the seat belts may
retract slowly. Wipe the shoulder belt
guide with a clean, dry cloth.
•Periodically check to see that the seat belt
and the metal components, such as buck-
les, tongues, retractors, flexible wires and
anchors, work properly. If loose parts, de-
terioration, cuts or other damage on the
webbing is found, the entire seat belt as-
sembly should be replaced.
WARNING
Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR)
mode seat belts. If the seat belt becomes
wrapped around a child’s neck with the
ALR mode activated, the child can be seri-
ously injured or killed if the seat belt re-
tracts and becomes tight. This can occur
even if the vehicle is parked. Unbuckle the
seat belt to release the child. If the seat belt
can not be unbuckled or is already unbuck-
led, release the child by cutting the seat
belt with a suitable tool (such as a knife or
scissors) to release the seat belt.
Children need adults to help protect them.
They need to be properly restrained.
In addition to the general information in this
manual, child safety information is available
from many other sources, including doctors,
teachers, government traffic safety offices,
and community organizations. Every child is
different, so be sure to learn the best way to
transport your child. There are three basic types of child restraint
systems:•Rear-facing child restraint
•Forward-facing child restraint
•Booster seat
The proper restraint depends on the child’s
size. Generally, infants up to about 1 year and
less than 20 lb (9 kg) should be placed in
rear-facing child restraints. Forward-facing
child restraints are available for children who
outgrow rear-facing child restraints and are
at least 1 year old. Booster seats are used to
help position a vehicle lap/ shoulder belt on a
child who can no longer use a forward-facing
child restraint.
WARNING
Infants and children need special protec-
tion. The vehicle’s seat belts may not fit
them properly. The shoulder belt may come
too close to the face or neck. The lap belt
may not fit over their small hip bones. In an
accident, an improperly fitting seat belt
could cause serious or fatal injury. Always
use appropriate child restraints.
CHILD SAFETY
Safety — seats, seat belts and supplemental restraint system1-17

A booster seat should be used until the child
can pass the seat belt fit test below:
•Are the child’s back and hips against the
vehicle seatback?
•Is the child able to sit without slouching?
•Do the child’s knees bend easily over the
front edge of the seat with feet flat on the
floor?
•Can the child safely wear the seat belt (lap
belt low and snug across the hips and
shoulder belt across mid-chest and shoul-
der)?
•Is the child able to use the properly ad-
justed head restraint/headrest?
•Will the child be able to stay in position for
the entire ride?
If you answered no to any of these questions,
the child should remain in a booster seat us-
ing a three-point type seat belt.
NOTE
Laws in some communities may follow dif-
ferent guidelines. Check local and state
regulations to confirm your child is using the
correct restraint system before traveling.
WARNING
Never let a child stand or kneel on any seat
and do not allow a child in the cargo area.
The child could be seriously injured or killed
in a sudden stop or collision.
SSS0099Z
WRS0256Z
CHILD RESTRAINTS
Safety — seats, seat belts and supplemental restraint system1-19

PRECAUTIONS ON CHILD
RESTRAINTS
WARNING
•Failure to follow the warnings and in-
structions for proper use and installa-
tion of child restraints could result in se-
rious injury or death of a child or other
passengers in a sudden stop or collision: – The child restraint must be used and
installed properly. Always follow all
of the child restraint manufacturer’s
instructions for installation and use.
– Infants and children should never be
held on anyone’s lap. Even the stron-
gest adult cannot resist the forces of
a collision.
– Do not put a seat belt around both a
child and another passenger.
– INFINITI
recommends that all child re-
straints be installed in the rear seat.
Studies show that children are safer
when properly restrained in the rear
seat than in the front seat. If you must
install a forward-facing child restraint
in the front seat, see "Forward-facing
child restraint installation using the
seat belts" in the "1. Safety — seats,
seat belts and supplemental restraint
system" section.
– Even with the INFINITI Advanced Air
bag System, never install a rear-
facing child restraint in the front
seat. An inflating air bag could seri-
ously injure or kill a child. A rear-
facing child restraint must only be
used in the rear seat.
– Be sure to purchase a child restraint
that will fit the child and vehicle.
Some child restraints may not fit
properly in your vehicle.
– Child restraint anchorages are de-
signed to withstand only those loads
imposed by correctly fitted child re-
straints. Under no circumstances are
they to be used to attach adult seat
belts, or other items or equipment to
the vehicle. Doing so could damage
the child restraint anchorages. The
child restraint will not be properly in-
stalled using the damaged anchor-
ages, and a child could be seriously
injured or killed in a collision.
– Never use the anchor points for adult
seat belts or harnesses.
– A child restraint with a top tether
strap should not be used in the front
passenger seat.
– Keep seatbacks as upright as possible
after fitting the child restraint. –
Infants and children should always be
placed in an appropriate child re-
straint while in the vehicle.
– When the child restraint is not in use,
keep it secured with the LATCH sys-
tem or a seat belt. In a sudden stop or
collision, loose objects can injure oc-
cupants or damage the vehicle.
CAUTION
Remember that a child restraint left in a
closed vehicle can become very hot. Check
the seating surface and buckles before
placing your child in a child restraint.
This vehicle is equipped with a universal child
restraint anchor system, referred to as the
LATCH (Lower Anchors and Tethers for
CHildren) system. Some child restraints in-
clude rigid or webbing-mounted attachments
that can be connected to these anchors.
For details, see "LATCH (Lower Anchors and
Tethers for CHildren) system" in the "1. Safety
— seats, seat belts and supplemental restraint
system" section.
If you do not have a LATCH compatible child
restraint, the vehicle seat belts can be used.
1-20Safety — seats, seat belts and supplemental restraint system

Several manufacturers offer child restraints
for infants and small children of various sizes.
When selecting any child restraint, keep the
following points in mind:
•Choose only a restraint with a label certi-
fying that it complies with Federal Motor
Vehicle Safety Standard 213 or Canadian
Motor Vehicle Safety Standard 213.
•Check the child restraint in your vehicle to
be sure it is compatible with the vehicle’s
seat and seat belt system.
•If the child restraint is compatible with
your vehicle, place your child in the child
restraint and check the various adjust-
ments to be sure the child restraint is com-
patible with your child. Choose a child re-
straint that is designed for your child’s
height and weight. Always follow all rec-
ommended procedures.
•If the combined weight of the child and
child restraint is less than 65 lb (29.5 kg),
you may use either the LATCH anchors or
the seat belt to install the child restraint
(not both at the same time).
•If the combined weight of the child and
child restraint is greater than 65 lb (29.5
kg), use the vehicle’s seat belt (not the
lower anchors) to install the child restraint.
•Be sure to follow the child restraint manu-
facturer’s instructions for installation. NOTE
All U.S. states and Canadian provinces or
territories require that infants and small
children be restrained in an approved child
restraint at all times while the vehicle is be-
ing operated. Canadian law requires the top
tether strap on front-facing child restraints
to be secured to the designated anchor point
on the vehicle.
LATCH (Lower Anchors and
Tethers for CHildren) system
Your vehicle is equipped with special anchor
points that are used with LATCH system
compatible child restraints. This system may
also be referred to as the ISOFIX or ISOFIX
compatible system. With this system, you do
not have to use a vehicle seat belt to secure
the child restraint unless the combined
weight of the child and child restraint exceeds
65 lb (29.5 kg). If the combined weight of the
child and child restraint is greater than 65 lb
(29.5 kg), use the vehicle’s seat belt (not the
lower anchors) to install the child restraint. Be
sure to follow the child restraint manufactur-
er’s instructions for installation.
The LATCH anchor points are provided to
install child restraints in the rear outboard
seating positions only. Do not attempt to
install a child restraint in the center position
using the LATCH anchors.
LATCH lower anchor
WARNING
Failure to follow the warnings and instruc-
tions for proper use and installation of child
restraints could result in serious injury or
death of a child or other passengers in a
sudden stop or collision:
•Attach LATCH system compatible child
restraints only at the locations shown in
the illustration.
•Do not secure a child restraint in the cen-
ter rear seating position using the
LATCH lower anchors. The child re-
straint will not be secured properly.
•Inspect the lower anchors by inserting
your fingers into the lower anchor area.
Feel to make sure there are no obstruc-
tions over the anchors such as seat belt
webbing or seat cushion material. The
child restraint will not be secured prop-
erly if the lower anchors are obstructed.
Child restraint anchorages are designed to
withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used to attach
adult seat belts, or other items or equip-
ment to the vehicle. Doing so could damage
Safety — seats, seat belts and supplemental restraint system1-21

that can be connected to two anchors lo-
cated at certain seating positions in your ve-
hicle. With this system, you do not have to
use a vehicle seat belt to secure the child
restraint. Check your child restraint for a label
stating that it is compatible with LATCH. This
information may also be in the instructions
provided by the child restraint manufacturer.
When installing a child restraint, carefully
read and follow the instructions in this
manual and those supplied with the child re-
straints.
Top tether anchor
WARNING
•Child restraint anchorages are designed
to withstand only those loads imposed
by correctly fitted child restraints. Un-
der no circumstances are they to be used
to attach adult seat belts, or other items
or equipment to the vehicle. Doing so
could damage the child restraint an-
chorages. The child restraint will not be
properly installed using the damaged
anchorage, and a child could be seriously
injured or killed in a collision.
•If the cargo cover (if so equipped) con-
tacts the top tether strap when it is at- tached to the top tether anchor, remove
the cargo cover from the vehicle or se-
cure it on the cargo floor below its at-
tachment location. If the cargo cover is
not removed, it may damage the top
tether strap during a collision. A child
could be seriously injured or killed in a
collision if the top tether strap is dam-
aged.
•Do not allow cargo to contact the top
tether strap when it is attached to the
top tether anchor. Properly secure the
cargo so it does not contact the top
tether strap. Cargo that is not properly
secured or cargo that contacts the top
tether strap may damage it during a col-
lision. A child could be seriously injured
or killed in a collision if the top tether
strap is damaged. Top tether anchor point locations for
LATCH:
1Top tether straps
2Anchor points
The LATCH anchor points are provided to
install child restraints in the rear outboard
seating positions only, as shown. Do not at-
tempt to install a child restraint in the center
position using the LATCH anchors.
If you have any questions when installing a
top tether strap, it is recommended that you
visit an INFINITI retailer for this service.
NIC2849
Safety — seats, seat belts and supplemental restraint system1-23

4. After attaching the child restraint, test itbefore you place the child in it. Push it
from side to side while holding the child
restraint near the LATCH attachment
path. The child restraint should not move
more than 1 inch (25 mm), from side to
side. Try to tug it forward and check to see
if the LATCH attachment holds the re-
straint in place. If the restraint is not se-
cure, tighten the LATCH attachment as
necessary, or put the restraint in another
seat and test it again. You may need to try
a different child restraint or try installing
by using the vehicle seat belt (if appli-
cable). Not all child restraints fit in all types
of vehicles. 5. Check to make sure the child restraint is
properly secured prior to each use. If the
child restraint is loose, repeat steps 2
through 4.
REAR-FACING CHILD
RESTRAINT INSTALLATION
USING THE SEAT BELTS
WARNING
The three-point seat belt with Automatic
Locking Retractor (ALR) must be used
when installing a child restraint. Failure to
use the ALR mode will result in the child
restraint not being properly secured. The
restraint could tip over or be loose and
cause injury to a child in a sudden stop or
collision.
Rear-facing child restraints must not be
used on the front seats.
For additional information, refer to all Warn-
ings and Cautions in the "Child safety" in the
"1. Safety — seats, seat belts and supplemen-
tal restraint system" section and "Child re-
straints" in the "1. Safety — seats, seat belts
and supplemental restraint system" section
before installing a child restraint. Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined
weight of the child and the child restraint is
greater than 65 lb (29.5 kg), use the vehicle
seat belt (not the lower anchors) to install the
child restraint. Be sure to follow the child
restraint manufacturer's instructions for in-
stallation.
Follow these steps to install a rear-facing
child restraint using the vehicle seat belts in
the rear seats:
1.
Child restraints for infants must be used
in the rear-facing direction and therefore
must not be used in the front seat. Posi-
tion the child restraint on the seat. Always
follow the child restraint manufacturer's
instructions.LRS0674Z
Rear-facing — step 4
WRS0256Z
Rear-facing — step 1
Safety — seats, seat belts and supplemental restraint system1-25

The LATCH anchor points are provided to
install child restraints in the rear outboard
seating positions only, as shown. Do not at-
tempt to install a child restraint in the center
position using the LATCH anchors.
WARNING
Child restraint anchorages are designed to
withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used to attach
adult seat belts, or other items or equip-
ment to the vehicle. Doing so could damage
the child restraint anchorages. The child re-
straint will not be properly installed using
the damaged anchorage, and a child could
be seriously injured or killed in a collision.Outboard seating positions with removable
head restraints/headrests:
1. If necessary, raise or remove the head
restraint/headrest and store it in a secure
place. Be sure to reinstall the head
restraint/headrest when the child re-
straint is removed. For additional informa-
tion about head restraint/headrest ad-
justment, removal and installation, refer to
"Head restraints/Headrests" in the "1.
Safety — seats, seat belts and supplemen-
tal restraint system" section.
2. Position the top tether strap
1over the
seatback as shown.
3. Secure the tether strap to the tether an- chor point
2on the seatback behind the
child restraint as shown.
4. Tighten the tether strap according to the manufacturer's instructions to remove
any slack.
Outboard seating positions with fixed head
restraints/headrests:
1. If the child restraint has a single tether strap, route the strap
1over the top of
the outer head restraint/headrest. If the
child restraint has two tether straps, route
them round each side of the outer head
restraint/headrest. 2. Secure the tether strap to the tether an-
chor point
2on the seatback behind the
child restraint as shown.
3. Tighten the tether strap according to the manufacturer's instructions to remove
any slack.
If you have any questions when installing
a top tether strap, it is recommended
that you visit an INFINITI retailer for this
service.
FORWARD-FACING CHILD
RESTRAINT INSTALLATION
USING THE SEAT BELTS
WARNING
The three-point seat belt with Automatic
Locking Retractor (ALR) must be used
when installing a child restraint. Failure to
use the ALR mode will result in the child
restraint not being properly secured. The
restraint could tip over or be loose and
cause injury to a child in a sudden stop or
collision. Also, it can change the operation
of the front passenger air bag. For addi-
tional information, refer to "Front passen-
ger air bag and status light" in the "1.
Safety — seats, seat belts and supplemen-
tal restraint system" section.
NIC2849
1-30Safety — seats, seat belts and supplemental restraint system

confirmed system operation, move the
child restraint to another position. See
"Troubleshooting" later in this section.
Installing top tether strap
WARNING
Child restraint anchorages are designed to
withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used to attach
adult seat belts, or other items or equip-
ment to the vehicle. Doing so could damage
the child restraint anchorages. The child re-
straint will not be properly installed using
the damaged anchorage, and a child could
be seriously injured or killed in a collision.
The child restraint top tether strap must be
used when installing the child restraint with
seat belts.
First, secure the child restraint with the seat
belt. Outboard seating positions with removable
head restraints/headrests:
1. If necessary raise or remove the headrestraint/headrest and store it in a secure
place. Be sure to reinstall the head restraint/headrest when the child re-
straint is removed. For additional informa-
tion about head restraint/headrest ad-
justment, removal and installation, refer to
"Head restraints/Headrests" in the "1.
Safety — seats, seat belts and supplemen-
tal restraint system" section.
2. Position the top tether strap1over the
seatback as shown.
3. Secure the tether strap to the tether an- chor point
2on the seatback behind the
child restraint as shown.
4. Tighten the tether strap according to the manufacturer's instructions to remove
any slack.
Outboard seating positions with fixed head
restraints/headrests:
1. If the child restraint has a single tether strap, route the strap
1over the top of
the outer head restraint/headrest. If the
child restraint has two tether straps, route
them round each side of the outer head
restraint/headrest.
2. Secure the tether strap to the tether an- chor point
2on the seatback behind the
child restraint as shown.
NIC2848
Rear seat - Type A
NIC2903
Rear seat - Type B
1-34Safety — seats, seat belts and supplemental restraint system