2018 INFINITI QX30 trailer

•Do not use the ICC system if you are
towing a trailer. The system may not de-
tect a vehicle ahead.
•In some road or traffic conditions, a ve-
hicle or object can unexpectedly come
into the sensor detection zone and cause
automatic braking. You may need to
control the distance from other vehicles
using the accelerator pedal. Always stay
alert and avoid using the ICC system
when it is not recommended in this sec-
tion.
•The distance sensor will not detect the
following objects: – Stationary and slow moving vehicles.
– Pedestrians or objects in the road-
way.
– Oncoming vehicles in the same lane.
– Motorcycles traveling offset in the
travel lane.
The following are some conditions in which
the sensor cannot properly detect a vehicle
ahead and the system may not operate prop-
erly:
•When the snow or road spray from travel-
ing vehicles reduces the sensor’s visibility.
•When excessively heavy baggage is
loaded in the rear seat or the luggage room
of your vehicle.
The ICC system is designed to automatically
check the sensor’s operation within the limi-
tation of the system. When the sensor is cov-
ered with dirt or is obstructed, the system will
automatically be canceled. If the sensor is
covered with ice, a transparent or translucent
vinyl bag, etc., the ICC system may not detect
them. In these instances, the ICC system may
not cancel and may not be able to maintain
the selected following distance from the ve-
hicle ahead. Be sure to check and clean the
sensor regularly.
TIPS FOR DRIVING WITH THE ICC
SYSTEM
General notes
The following contains descriptions of cer-
tain road and traffic conditions in which you
must be particularly attentive. In such situa-
tions, brake if necessary. The ICC system is
then deactivated
Cornering, entering and exiting a
bend
The ability of the ICC system to detect ve-
hicles when cornering is limited. Your vehicle
may brake unexpectedly or late.
NSD603
5-58Starting and driving

Use the following procedure to turn the FEB
system on or off:
1. Press the
button on the
steering wheel
1to select the [DriveAs-
sist] menu on the Menu bar
B.
2. Press the
orbutton to select
[Emergency Brake].
3. Press the button on the steering
wheel
1. The current selection is dis-
played.
4. To activate/deactivate the FEB system: press the button again
When the FEB system is deactivated, the
symbolCappears in the vehicle infor-
mation display. NOTE
The FEB system will be automatically turned
on when the engine is restarted.
FEB SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for
the FEB system. Failure to operate the ve-
hicle in accordance with these system limi-
tations could result in serious injury or
death.
•The FEB system cannot detect all ve-
hicles under all conditions.
•The radar sensor does not detect the
following objects: – Pedestrians or animals
– Oncoming vehicles
– Crossing vehicles
•The radar sensor has some performance
limitations. For stationary vehicles, the
FEB system will not function when the
vehicle is driven at speeds over: –
Approximately 31 MPH (50 km/h) for
the Autonomous braking function.
•The radar sensor may not detect a ve-
hicle ahead in the following conditions: – Dirt, ice, snow or other material cov-
ering the radar sensor. –
Interference by other radar sources.
– Snow or heavy rain.
– If the vehicle ahead is narrow (e.g.
motorcycle).
– If the vehicle ahead is in a different
lane.
– Under strong radar reflections, for
example, in a multi-level parking ga-
rage.
– New vehicle or after a maintenance
of the FEB system. For additional in-
formation, see "Break-in schedule"
later in this section
– When driving on a steep downhill
slope or roads with sharp curves.
– When towing a trailer.
•In some road or traffic conditions, the
FEB system may intervene unnecessar-
ily or give an unnecessary warning. Al-
ways pay careful attention to the traffic
situation. Do not rely solely on the dis-
tance warning function and terminate
the intervention if necessary.
•Braking distances increase on slippery
surfaces.
NSD630
Starting and driving5-67

IPA is an electronic parking aid with ultra-
sound. It detects vehicles and open spaces on
both sides of the vehicle. A parking symbol
indicates a suitable parking space. Active
steering intervention can assist you during
parking and when exiting a parking space.
The driver controls the accelerator, brake and
gear shift. You may also use the Camera Aid-
ing Sonar (parking sensor) function (see "
Camera Aiding Sonar (parking sensor) func-
tion (if equipped)" later in this section).
IMPORTANT SAFETY NOTES
WARNING
•IPA is only an aid. It is not a substitute
for your attention to the immediate sur-
roundings. The responsibility for safe
maneuvering and parking remains with
you.
•Make sure that no persons, animals or
objects are in the maneuvering range
•When the sonar (parking sensor) func-
tion is deactivated, IPA is also unavail-
able.
•While parking or pulling out of a parking
space, the vehicle swings out and can
drive onto areas of the oncoming lane.
This could cause you to collide with other road users. There is a risk of an
accident.
•Pay attention to other road users. Stop
the vehicle if necessary or cancel the IPA
parking procedure
•This system is not designed to prevent
contact with small or moving objects.
•If your vehicle sustains damage to the
bumper fascia, leaving it misaligned or
bent, the sensing zone may be altered
causing inaccurate measurement of ob-
stacles or false alarms.
•This system is not designed to prevent
contact with small or moving objects.
•If your vehicle sustains damage to the
bumper fascia, leaving it misaligned or
bent, the sensing zone may be altered
causing inaccurate measurement of ob-
stacles or false alarms.
CAUTION
Do not drive over obstacles such as curbs,
as you may damage the wheels or tires.
IPA may also display spaces not suitable for
parking, for example:
•Parking or stopping prohibition.
•In front of driveways or entrances and
exits.
•Unsuitable surfaces.
Parking tips:
•On narrow roads, drive as closely as pos-
sible past the parking space.
•Parking spaces that are littered or over-
grown might be identified or measured
incorrectly.
•Parking spaces that are partly occupied by
trailer towing bars might not be identified
as such or be measured incorrectly.
•Snowfall or heavy rain may lead to a park-
ing space being measured inaccurately.
•Pay attention to the sonar function warn-
ing messages during the parking proce-
dure.
•You can intervene in the steering proce-
dure to correct it at any time. IPA will then
be canceled.
•When transporting a load which protrudes
from your vehicle, you should not use IPA.
•Never use IPA when snow chains are fit-
ted.
•Make sure that the tire pressures are al-
ways correct. This has a direct influence on
the parking characteristics of the vehicle.
INTELLIGENT PARKING ASSIST (IPA)
(IF EQUIPPED)
Starting and driving5-71

Use IPA for parking spaces that are:
•Parallel or at right angles to the direction
of travel.
•On straight roads, not bends.
•On the same level as the road, e. g. not on
the sidewalk.
For vehicles with the towbar folded out, the
minimum length for parking spaces is slightly
longer.
If you have attached a trailer to your vehicle,
you may not use IPA. Once the electrical
connection is established between your ve-
hicle and the trailer, IPA is no longer available.
The sonar function is deactivated for the rear
area
DETECTING PARKING SPACES
The IPA system can only be used to park in
spaces that have vehicles directly on either
side of the parking space.
Objects located above the height range of
IPA will not be detected when the parking
space is measured. These are not taken into
account when the parking procedure is calcu-
lated, e. g. overhanging loads, tail sections or
loading ramps of goods vehicles.
WARNING
If there are objects above the detection
range, IPA may steer too early. This could
cause a collision. There is a risk of an acci-
dent.
If objects are located above the detection
range, stop and switch off the IPA.
For further information on the detection
range see "Range of the sensors" later in this
section.
IPA does not assist you parking in spaces at
right angles to the direction of travel if:
•Two parking spaces are located directly
next to one another.
•The parking space is directly next to a low
obstacle such as a low curb.
•You forward park.
IPA does not assist you parking in spaces that
are parallel or at right angles to the direction
of travel if:
•The parking space is on a curb.
•The system reads the parking space as
being blocked, for example, by foliage or
grass paving blocks.
•The area is too small for the vehicle to
maneuver into.
•The parking space is bordered by an ob-
stacle, e.g. a tree, a post or a trailer.
5-72Starting and driving

The sonar function is deactivated for the rear
area when you establish an electrical connec-
tion between your vehicle and a trailer.
RANGE OF THE SENSORS
The sonar function does not take into ac-
count obstacles located:
•Below the detection range, e.g. persons,
animals or objects.
•Above the detection range, e.g. overhang-
ing loads, tail sections or loading ramps of
goods vehicles.
SONAR FUNCTION OFF SWITCH
The sonar function OFF switch2on the
lower side of the instrument panel allows the
driver to turn the sonar function on and off.
To turn the sonar function system on and off,
the ignition switch must be in the ON posi-
tion. The indicator light
1on the switch will
illuminate when the system is turned off.
The sonar function will turn on automatically
when the ignition switch is turned from the
OFF position to the ON position.
NIC2635
5-82Starting and driving

SYSTEM MAINTENANCE
CAUTION
Keep the surface of the sonar sensors (if
equipped) (located on the front and rear
bumper fascia) free from accumulations of
snow, ice and dirt. Do not scratch the sur-
face of the sonar sensors when cleaning. If
the sensors are covered, the accuracy of
the sonar function will be diminished.During the first 1,200 miles (2,000 km), fol-
low these recommendations to obtain maxi-
mum engine performance and ensure the fu-
ture reliability and economy of your new
vehicle. Failure to follow these recommenda-
tions may result in shortened engine life and
reduced engine performance.
•Avoid driving for long periods at constant
speed, either fast or slow, and do not run
the engine over 4,000 RPM.
•Do not accelerate at full throttle in any
gear.
•Avoid quick starts.
•Avoid hard braking as much as possible.
•Do not tow a trailer for the first 500 mi
(805 km). Your engine, axle or other parts
could be damaged.
You should also observe these notes on
break-in if the engine or parts of the drive
train on your vehicle have been replaced.
CAUTION
In certain driving and driving safety sys-
tems, the sensors adjust automatically
while a certain distance is being driven af-
ter the vehicle has been delivered or after
repairs. Full system effectiveness is not
reached until the end of this teach-in pro-
cess.
Brake pads/linings and rotors that are ei-
ther new or have been replaced only
achieve optimum braking effect after sev-
eral hundred miles of driving. Compensate
for the reduced braking effect by applying
greater force to the brake pedal
BREAK-IN SCHEDULE
Starting and driving5-85

Propeller shaft(s):
Check for damage, looseness, and grease
leakage. (4WD/AWD).
Steering gear and linkage, axle and suspen-
sion parts, drive shaft boots:
Check for damage, looseness, and leakage of
oil or grease. Under severe driving conditions,
inspect more frequently
Tire rotation:
Tires should be rotated every 5,000 miles
(8,000 km) according to the instructions un-
der "Tire rotation*" earlier in this section.
When rotating tires, check for damage and
uneven wear. Replace if necessary.
Transmission fluid/oil, differential oil,
transfer case oil:
Visually inspect for signs of leakage at speci-
fied intervals.To ensure smooth, trouble-free, safe and
economical driving, INFINITI provides two
maintenance schedules that may be used,
depending upon the conditions in which you
usually drive. These schedules contain both
distance and time intervals, up to 120,000
miles (192,000 km)/144 months. For most
people, the odometer reading will indicate
when service is needed. However, if you drive
very little, your vehicle should be serviced at
the regular time intervals shown in the sched-
ule.
After 120,000 miles (192,000 km)/144
months, continue maintenance at the same
mileage/time intervals.
ADDITIONAL MAINTENANCE
ITEMS FOR SEVERE OPERATING
SYSTEMS
Additional maintenance items for severe op-
erating conditions; should be performed on
vehicles that are driven under especially de-
manding conditions. Additional maintenance
items should be performed if you primarily
operate your vehicle under the following con-
ditions:
•Repeated short trips of less than 5 miles in
normal temperatures or less than 10 miles
in freezing temperatures.
•Stop-and-go traffic in hot weather or low
speed driving for long distances.
•Driving in dusty conditions or on rough,
muddy or salt-spread roads.
•Towing a trailer, or using a camper or car-
top carrier.
OIL CHANGE MONITOR
This vehicle is equipped with oil change moni-
tor. It calculates engine oil and filter change
interval base on driving conditions. Driving in
severe conditions will shorten the engine oil
and filter change interval. When the Engine
Oil – Service Due Now warning appears in
the vehicle information display, the engine oil
and filter need to be replaced.
NOTE
For vehicles operated in Canada, both stan-
dard and severe maintenance items should
be performed at every interval.
MAINTENANCE SERVICE
MESSAGES
The maintenance service interval display in-
forms you of the next service due date.
NOTE
The maintenance service interval display
does not show any information on the engine
oil level.
MAINTENANCE SCHEDULES
Maintenance and Schedules9-7

10 Technical information
Recommended fluids/lubricants and capacities . .10-2Fuel recommendation ............... .10-3
Engine oil and oil filter recommendations . . . .10-5
Air conditioner system refrigerant and oil
recommendations .................. .10-6
Engine specifications .................. .10-7
Wheels and Tires .................... .10-8
Dimensions ........................ .10-9
When traveling or registering in another
country ......................... .10-10
Vehicle identification ................. .10-10
Vehicle identification number (VIN) plate . . .10-10
Vehicle identification number (chassis
number) ....................... .10-11
Engine serial number ............... .10-11
F.M.V.S.S./C.M.V.S.S. Certification label. . . .10-11
Emission control information label .......10-12
Tire and loading information label ........10-12
Air conditioner specification label ........10-12Installing front license plate
..............10-13
Vehicle loading information ..............10-14
TERMS ....................... .10-14
Vehicle load capacity ............... .10-15
Loading tips .................... .10-16
Measurement of weights .............10-16
Trailer towing ..................... .10-16
Uniform tire quality grading ..............10-17
Treadwear ..................... .10-17
Traction AA, A, B and C ..............10-17
Temperature A, B and C ..............10-17
Emission control system warranty .........10-18
Reporting safety defects ...............10-18
Readiness for inspection/maintenance (I/M)
test ............................ .10-19
Event data recorders (EDR) (if so equipped) . . .10-20
Owner's manual/service manual order
information ....................... .10-20