2018 INFINITI QX30 Front cover

•On vehicles with a push button ignition
switch: you must remove the start/stop
button and use the key (see " Push-
button ignition switch (if equipped)").
Otherwise the automatic transmission
may shift to position P (Park) when the
driver's or front passenger door are
opened, which could lead to damage to
the transmission.
If your vehicle is stuck in sand, snow, mud,
etc., use a tow strap or other device designed
specifically for vehicle recovery. Always fol-
low the manufacturer’s instructions for the
recovery device.
Rocking a stuck vehicle
WARNING
•To avoid potential injury, stand clear of
a stuck vehicle.
•Do not spin your tires at high speed. This
could cause them to explode and result
in serious injury. Parts of your vehicle
could also overheat and be damaged.If your vehicle is stuck in sand, snow, mud,
etc., use the following procedure:
1. Turn off the Vehicle Dynamic Control
(VDC) system.
2. Make sure the area in front and behind the
vehicle is clear of obstructions.
3. Turn the steering wheel right and left to
clear an area around the front tires.
4. Slowly rock the vehicle forward and back-
ward.
•Shift back and forth between R (Reverse)
and D (Drive).
•Apply the accelerator as little as possible
to maintain the rocking motion.
•Release the accelerator pedal before shift-
ing between R (Reverse) and D (Drive).
•Do not spin the tires above 35 MPH
(55 km/h).
5. If the vehicle cannot be freed after a few
tries, contact a professional towing ser-
vice to remove the vehicle.
6-16In case of emergency

2. Hold the battery top cover firmly and slide
it towards the front of the car
2and
upwards
3.
3. Lift the cover up and away from the bat-
tery.
NOTE
When installing the battery cover, remem-
ber to replace cables in their original posi-
tion.
MAINTENANCE FREE BATTERY
For a maintenance free battery it is not re-
quired to check the fluid level. However,
INFINITI recommends to visually check the
status of the green indicator
A(if so
equipped) periodically. If it is not visible, re-
place the battery as soon as possible.
MODELS WITH IDLE
STOP/START SYSTEM
•Ensure that the battery fitted is the special
battery that is enhanced with regard to the
charge-discharge capacity and life perfor-
mance. Avoid using any other battery for
the Idle Stop/Start System, as this may
cause early deterioration of the battery or
a malfunction of the Idle Stop/Start Sys-
tem. It is recommended that a Genuine
INFINITI battery is fitted. For more infor-
mation, it is recommended that you con-
tact an INFINITI retailer.
•If the battery terminal is disconnected (for
battery replacement, etc.) and then recon-
nected, there may be some delay before
the Stop/Start System reactivates.
BATTERY REPLACEMENT
It is recommended that a Genuine INFINITI
battery is fitted. It is recommended that you
visit an INFINITI retailer for this service.
Protective plate for battery
WARNING
Whenever the battery is replaced, always
have the protective plate underneath the
battery also reinstalled or replaced. If this
plate is not reinstalled/replaced, in the
NDI920Z
8-10Do-it-yourself

3. Fold down cover1.
4. Hook clamps into the fuse box and close
5. Close the hood.
PASSENGER COMPARTMENT
WARNING
Never use a fuse of higher or lower amper-
age rating than that specified on the fuse
box cover. This could damage the electrical
system or electronic control units or cause
a fire.To open:
1. Open the front-passenger door.
2. Remove the floor mats.
3. Fold out perforated floor covering
1in
the direction of the arrow.
NDI1593
Do-it-yourself8-19

5. Insert the new battery with the positive
terminal facing upwards. Use a lint-free
cloth to do so.
6. Make sure that the surface of the battery
is free of lint, grease and other contami-
nation.
7. Insert the front tabs of battery cover
1and then press to close it.
8. Insert emergency key element into the key
(see "Mechanical key").
9. Check the function of all key buttons on
the vehicle.
If you need assistance with replacement, it is
recommended that you visit an INFINITI re-
tailer for this service.FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this de-
vice must accept any interference received,
including interference that may cause unde-
sired operation.
NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compli-
ance could void the user’s authority to oper-
ate the equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause unde-
sired operation of the device.
SPA0784Z
8-22Do-it-yourself

LED type:
1Cornering light
2Additional high-beam headlight
3Daytime driving light and sidelight and
turn signal light
4High/Low beam LED projector head-
lights and Adaptive Front Lighting sys-
tem (if so equipped)
5Side marker light (if so equipped)
6Reflector (if so equipped)
7Daytime driving light and sidelights
Rear light unit
1Tail light
2Turn signal light
3Brake light
4Tail light
5Reversing light
6Rear fog light (drivers side only)
REPLACEMENT PROCEDURES
LED lights (if so equipped)
The LED headlight is a projector style which
uses a LED module without serviceable parts.
If LED fog headlight , or any other LED light
replacement is required, it is recommended
that you visit an INFINITI retailer for this
service.
Halogen headlight bulb
Fitting/removing the access cover on the
front wheel arch:
You must remove the cover of the front
wheel arch before you can change the halo-
gen headlight bulb.
To remove: switch off the lights, turn the
steering so that the wheel behind the light in
question is pointing inwards . Slide cover
1up and remove it.
To fit: inset cover
1again and slide it down
until it engages.
NDI1614NDI1615NDI1626
Do-it-yourself8-25

The headlight is a semi-sealed beam type
which uses a replaceable headlight (halogen)
bulb. A bulb can be replaced from inside the
engine compartment without removing the
headlight assembly.
If you need assistance for bulb replacement,
it is recommended that you visit an INFINITI
retailer.
Low/High beam Headlight bulb replace-
ment:
1. Open the hood. For details, see "Hood".
2. Disconnect the negative (—) battery cable.
3. Remove the corresponding access cover
from the wheel arch.
4. Turn housing cover
1counterclockwise
and remove it.
5. Turn bulb holder
2counterclockwise and
pull out
6. Take the headlight bulb out of bulb holder
2.
7. Insert the new bulb into bulb holder
2.
8. Insert bulb holder
2and turn it clockwise.9. Press on housing cover
1and turn it to
the right.
10. Replace the cover in the front wheel arch
11. Reconnect the negative (—) battery cable
and close the hood.
NOTE
Fog may temporarily form inside the lens of
the exterior lights in the rain or in a car wash.
The fog is caused by a temperature differ-
ence between the inside and the outside of
the lens. This is not a malfunction. If large
droplets can be seen, it is recommended that
you visit an INFINITI retailer.
NDI1611
8-26Do-it-yourself

Front turn signal light bulb
replacement (non-LED system only)
1. Open the hood. For details, see "Hood".
2. Disconnect the negative (—) battery cable.
3. Turn housing cover
1counterclockwise
and remove it.
4. Turn bulb holder
2counterclockwise and
pull out
5. Take the headlight bulb out of bulb holder
2.
6. Insert the new bulb into bulb holder
2.7. Insert bulb holder
2and turn it clockwise.
8. Press on housing cover
1and turn it to
the right.
9. Reconnect the negative (—) battery cable
and close the hood.If you have a flat tire, refer to "Flat tire".TIRE PRESSURE
Tire Pressure Monitoring System
(TPMS)
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the
low tire pressure warning light is lit, one or
more of the tires is significantly under-
inflated.
The TPMS will activate only when the vehicle
is driven at speeds above 16 MPH (25 km/h).
Also, this system may not detect a sudden
drop in tire pressure (for example a flat tire
while driving).
For additional information, refer to "Tire
Pressure Monitoring System (TPMS)".
NDI1612
WHEELS AND TIRES
Do-it-yourself8-27

Before driving a loaded vehicle, confirm that
you do not exceed the Gross Vehicle Weight
Rating (GVWR) or the Gross Axle Weight
Rating (GAWR) for your vehicle. (See "Mea-
surement of weights" later in this section.)
Also check tires for proper inflation pres-
sures. See the Tire and Loading Information
label.
LOADING TIPS
•The GVW must not exceed GVWR or
GAWR as specified on the F.M.V. S.S./
C.M.V.S.S. certification label.
•Do not load the front and rear axle to the
GAWR. Doing so will exceed the GVWR.
WARNING
•Properly secure all cargo to help prevent
it from sliding or shifting. Do not place
cargo higher than the seatbacks. In a
sudden stop or collision, unsecured
cargo could cause personal injury.
•Do not load your vehicle any heavier
than the GVWR or the maximum front
and rear GAWRs. If you do, parts of your
vehicle can break, tire damage could oc-
cur, or it can change the way your ve-
hicle handles. This could result in loss of
control and cause personal injury.
•Overloading could not only shorten the
life of your vehicle and the tires, but also
could cause unsafe vehicle handling and
longer braking distances. This may
cause a premature tire failure which
could result in a serious accident and
personal injury. Failures caused by over-
loading are not covered by the vehicle's
warranty.
MEASUREMENT OF WEIGHTS
Secure loose items to prevent weight shifts
that could affect the balance of your vehicle.
When the vehicle is loaded, drive to a scale
and weigh the front and the rear wheels
separately to determine axle loads. Individual
axle loads should not exceed either of the
gross axle weight ratings (GAWR). The total
of the axle loads should not exceed the gross
vehicle weight rating (GVWR). These ratings
are given on the vehicle certification label. If
weight ratings are exceeded, move or remove
items to bring all weights below the ratings.Your vehicle was designed to be used to carry
passengers and luggage
CAUTION
Do not tow a trailer with your vehicle.
TRAILER TOWING
Technical information10-15