2018 INFINITI QX30 wiper

SWITCHING THE WINDSHIELD
WIPERS ON/OFF
1Windshield wipers off.
2Intermittent wipe, low (rain sensor
set to low sensitivity).
3Intermittent wipe, high (rain sen-
sor set to high sensitivity).
4Continuous wipe, slow.
5Continuous wipe, fast.
ASingle wipe/
wipe the windshield using washer fluid.
The windshield wiper and washer operate
when the ignition switch is in the ON position.
Turn the combination switch to the desired
position.
Rain sensor (if equipped)
The rain-sensing auto wiper system uses the
rain sensor located on the upper part of the
windshield
1.
CAUTION
•Do not touch the rain sensor and around
it
1when the wiper switch is in the
orposition and the ignition switch
is in the ON position. The wipers may
operate unexpectedly and cause an in-
jury or may damage a wiper.
•The rain-sensing auto wipers are in-
tended for use during rain. If the switch
is left in the
orposition, the
wipers may operate unexpectedly when
dirt, fingerprints, oil film or insects are
stuck on or around the sensor. The wip-
ers may also operate when exhaust gas
or moisture affect the rain sensor.
•When the windshield glass is coated
with water repellent, the speed of the
rain-sensing auto wipers may be higher
even though the amount of the rainfall is
small.
•Be sure to turn off the rain-sensing auto
wiper system when you use a car wash.
•The rain-sensing auto wipers may not
operate if rain does not hit the rain sen-
sor even if it is raining.
•Using genuine wiper blades is recom-
mended for proper operation of the
rain-sensing auto wiper system. For ad-
ditional information, refer to "Wiper
blades".
NIC2810
Combination switch
NSD610
2-62Instruments and controls

•Vehicles with a rain sensor: if the wind-
shield becomes dirty in dry weather con-
ditions, the windshield wipers may be
activated inadvertently. This could
damage the windshield wiper blades or
scratch the windshield.
For this reason, you should always
switch off the windshield wipers in dry
weather.
Vehicles with a rain sensor: in the
orposition, the appropriate wiping fre-
quency is automatically set according to the
intensity of the rain. In the
position, the
rain sensor is more sensitive than in the
position, causing the windshield wiper
to wipe more frequently.
If the wiper blades are worn, the windshield
will no longer be wiped properly. This could
prevent you from observing the traffic condi-
tions.
SWITCHING THE REAR WINDOW
WIPER ON/OFF
WARNING
In freezing temperatures the washer solu-
tion may freeze on the windshield and ob-
scure your vision which may lead to an ac-
cident. Warm the windshield with the
defroster before you wash the windshield.
CAUTION
•Do not operate the washer continuously
for more than 30 seconds.
•Do not operate the washer if the win-
dow washer fluid reservoir is empty.
•Do not fill the window washer reservoir
tank with washer fluid concentrates atfull strength. Some methyl alcohol
based washer fluid concentrates may
permanently stain the grille if spilled
while filling the window washer reser-
voir tank.
•Pre-mix washer fluid concentrates with
water to the manufacturer’s recom-
mended levels before pouring the fluid
into the window washer reservoir tank.
Do not use the window washer reservoir
tank to mix the washer fluid concentrate
and water.
1Switch
2Wipes with washer fluid
3Switches on intermittent wiping
4Switches off intermittent wiping
5Wipes with washer fluid
1. Switch the ignition switch to the ON po-
sition.
2. Turn switch
1on the combination switch
to the corresponding position.
When the rear window wiper is switched
on, the
symbol appears in the as-
sistance graphic in the combination meter.
Further information on the assistance
graphic (see "Showing the distance
display" earlier in this section).
NIC2617
Instruments and controls2-63

1. Make sure that the windshield wipers are
switched off.
2. Pull the hood lock release lever
1, lo-
cated below the instrument panel on
the driver's side; the hood will spring up
slightly.3. Push the lever2at the front of the hood,
to the left with your fingertips and raise
the hood.
NDI1603NDI1627
HOOD
Pre-driving checks and adjustments3-15

NOTE
You should only select this setting until the
windshield is clear again.
Windows misted up on the outside:
1. Activate the windshield wipers.
2. Set the air distribution to
or.
NOTE
You should only select this setting until the
windows are clear again.
Air recirculation mode
You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle
from outside. The air already inside the ve-
hicle will then be recirculated.
If you activate air-recirculation mode, the
windows can mist up more quickly, in particu-
lar at low temperatures. Only use air recircu-
lation mode briefly to prevent the windows
misting up.
Activating air recirculation mode:
Make sure the ignition switch is in the ON
position.
Press the
button. The indicator light in
thebutton lights up.Deactivating air recirculation mode:
Press the
button. The indicator light in
thebutton goes out.
NOTE
Air-recirculation mode is deactivated auto-
matically:
•After approximately five minutes at out-
side temperatures below approximately
45° F (7°C).
•After approximately five minutes if the
"Cooling with air dehumidification" func-
tion is deactivated.
•After approximately 30 minutes at outside
temperatures above approximately 45° F
(7°C) if the cooling with air dehumidifica-
tion function is activated.
Idle Stop/Start function
During automatic engine switch-off, the Cli-
mate control only operates at a reduced ca-
pacity. If you require the full climate control
output, you can switch off the Idle Stop/
Start function by pressing the ECO button
(see " Idle Stop/Start System (if equipped)").
Display screen, heater and air conditioner, and audio system4-33

The temperature setting for the driver's side
is adopted for the front-passenger side.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.
NOTE
You should only select the "Windshield de-
misting" function until the windshield is clear
again.
Activating the "Windshield demisting"
function:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indi-
cator light in thebutton lights up.
The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode offNOTE
•The "Windshield demisting" function auto-
matically sets the blower output to the
optimum demisting effect. As a result, the
airflow may increase or decrease auto-
matically after the
button is pressed.
•You can adjust the blower output man-
ually while the "Windshield demisting"
function is in operation. Press the
orbutton.
Deactivating the "Windshield demisting"
function:
Press the
button. The indicator light in
thebutton goes out. The previous set-
tings are reactivated Air-recirculation mode
remains deactivated.
or
Turn temperature control
1or9counter-
clockwise or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate the
"Cooling with air dehu-
midification" function.
2. Activate automatic mode
.3. If the windows continue to mist up, acti-
vate the
"Windshield demisting"
function.
NOTE
You should only select this setting until the
windshield is clear again.
Windows misted up on the outside:
1. Activate the windshield wipers.
2. Set the air distribution to
or.
NOTE
You should only select this setting until the
windows are clear again.
Air recirculation mode
You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle
from outside. The air already inside the ve-
hicle will then be recirculated.
If you activate air-recirculation mode, the
windows can mist up more quickly, in particu-
lar at low temperatures. Only use air recircu-
lation mode briefly to prevent the windows
misting up.
Activating air recirculation mode:
Make sure the ignition switch is in the ON
position.
Display screen, heater and air conditioner, and audio system4-37

If you lock the vehicle with the key's remote
control or with the Intelligent Key, after a
short time:
•You will not be able to switch on the igni-
tion with the push-button ignition switch.
•You will not be able to start the engine
with the push-button ignition switch until
the vehicle is unlocked again.
If you lock the vehicle centrally using the but-
ton on the front door (see "Locking with in-
side door knob"). you can continue to start the
engine with the push-button ignition switch.
KEY POSITIONS WITH THE
PUSH-BUTTON IGNITION
SWITCH
1Start/Stop button
2Ignition lock
When you switch on the ignition, all of the
indicator lights in the combination meter light
up. For further information on situations
where an indicator light either fails to go out
after starting the engine or lights up while
driving see "Warning lights, indicator lights
and audible reminders".
If the push-button ignition switch
1has not
yet been pressed, this corresponds to the key
being removed from the ignition.
To switch on the power supply (accessory
mode):press the push-button ignition switch
1once without depressing the brake pedal.The power supply is switched on. You can
now activate the windshield wipers, for ex-
ample.
The power supply is switched off again if the
driver's door is opened and you press the
push-button ignition switch
1twice when in
this position.
To switch on the ignition:press the push-
button ignition switch
1twice without de-
pressing the brake pedal. The ignition is
switched on.
The ignition is switched off if the driver's door
is opened and you press the push-button
ignition switch
1when in this position.
REMOVING THE START/STOP
BUTTON
You can remove the start/stop button from
the ignition lock and start the vehicle as nor-
mal using the key.
You can only switch between push-button
ignition switch mode and key operation when
the vehicle is stationary.
You must also engage park position P (Park).
Remove the start/stop button
1from igni-
tion lock
2.
NPA1484
Starting and driving5-15

8 Do-it-yourself
Maintenance precautions.................8-2
Engine compartment check locations.........8-3
2.0L Gasoline engine.................8-3
Engine cooling system...................8-3
Checking engine coolant level............8-4
Changing engine coolant...............8-4
Engine oil...........................8-5
Checking engine oil level...............8-5
Changing engine oil..................8-5
Changing engine oil filter...............8-6
Automatic Transmission Fluid (ATF)..........8-7
Brake fluid..........................8-7
Window washer fluid...................8-8
Battery............................8-9
Accessing Vehicle battery...............8-9
Maintenance free battery..............8-10
Models with Idle Stop/Start System.......8-10
Battery replacement.................8-10
Reinitialisation procedure after battery
reconnection......................8-12
Jump-starting.....................8-12
Drive belt..........................8-12
Spark plugs.........................8-12
Air cleaner filter......................8-13
Wiper blades........................8-13Cleaning.........................8-13
Replacing front window wiper blades......8-14
Replacing rear window wiper blade.......8-16
Brakes............................8-17
Self-adjusting brakes.................8-17
Fuses.............................8-17
Before replacing a fuse...............8-17
Engine compartment.................8-18
Passenger compartment..............8-19
Intelligent Key battery replacement........
.8-20
Checking the battery.................8-21
Replacing the battery.................8-21
Lights............................8-23
Exterior and interior lights..............8-23
Replacement procedures..............8-25
Wheels and tires......................8-27
Tire Pressure......................8-27
Tire inflation pressure................8-30
Tire labeling......................8-30
Types of tires.....................8-32
Tire chains.......................8-33
Tire wear and damage................8-33
Tire rotation......................8-34
Replacing wheels and tires.............8-34
Wheel balance.....................8-36

It is recommended that you visit an INFINITI
retailer if checking or replacement is required.
WARNING
•Operating the engine with the air
cleaner filter off can cause you or others
to be burned. The air cleaner filter not
only cleans the intake air, it also stops
the flame if the engine backfires. If the
air cleaner is not installed and the engine
backfires, you could be burned. Never
drive with the air cleaner filter off. Be
cautious working on the engine when
the air cleaner is off.
•Never pour fuel into the throttle body or
attempt to start the engine with the air
cleaner removed. Doing so could result
in serious injury.
CLEANING
If the windshield or rear window is not clear
after using the window washer or if a wiper
blade chatters when running, wax or other
material may be on the blade or windshield.
Clean the outside of the windshield or rear
window with a washer solution or a mild
detergent. The windshield or rear window is
clean if beads do not form when rinsing with
clear water.
Clean the blade by wiping it with a cloth
soaked in a washer solution or a mild deter-
gent. Then rinse the blade with clear water. If
the windshield or rear window is still not clear
after cleaning the blades and using the wiper,
replace the blades.
CAUTION
Worn windshield wiper blades can damage
the windshield and impair driver vision.
AIR CLEANER FILTER WIPER BLADES
Do-it-yourself8-13