8
5
6
Cruise Control
3
2
1
4
3
2 1
CONVENTIONAL CRUISE CONTROL (if so equipped)
SETTING A CRUISING SPEED
•
Press the CRUISE ON/OFF switch 1 to turn on the system.
•
With the
vehicle at the desired speed, push down the switch
2 to COAST/SET to
enable cruise control.
•
The cruising speed c
an be adjusted to a higher or lower speed by toggling the
control switch
2 up or down.
CANCELING THE PRESET SPEED
•
Push the CANCEL switch
3 or tap the brake pedal.
INTELLIGENT CRUISE CONTROL (ICC) (if so equipped)
The ICC system is designed to maintain a selected distance from the vehicle in front of
you and reduce the speed to match a slower vehicle ahead.
•
T
o increase the distance to the vehicle ahead to be maintained by the ICC system,
push the distance switch
4 until the display shows the desired set distance, which
is shown by the number of lines on the set distance indicator
5.
•
When a
vehicle is detected ahead, a car icon will illuminate on the vehicle ahead
detection indicator
6 and your vehicle will reduce the speed to match the
slower vehicle.
To use Conventional (fixed speed) Cruise Control mode (if so equipped):
•
While cruise c
ontrol is off, push and hold the CRUISE ON/OFF switch
1 for more
than 1.5 seconds. The CRUISE indicator light will illuminate.
•
A
ccelerate to the desired speed.
•
Push the swit
ch
2 down toward COAST/SET and release it. The SET indicator
light will illuminate.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and
feature information.
INTELLIGENT CRUISE CONTROL (ICC) (if so equipped)
2917603_18a_Q70_US_pQRG_051717.indd 85/17/17 2:25 PM
14
Move the lever 1 up or down to one of
the following positions to operate the
windshield wipers:
MIST
One sw
eep operation
OFF
Wipers ar
e OFF
AUTO
R
ain-sensing automatic wipe
LO
C
ontinuous wipe, slow
HI
C
ontinuous wipe, fast
To adjust the wiper sensitivity for the AUTO
setting, twist the control ring
2.
Pull the lever
1 toward you operate the
windshield washer.
To turn the rain-sensing automatic wiper
system off, push up the lever to the OFF
position, or pull down the lever to the LO or
HI position.
Wiper and Washer Switch
1
2
SYSTEM OPERATING TIPS •
The in terior of the vehicle should be as quiet
as possible.
•
Speak
naturally. Speaking too fast, too slow, too
soft, or too loud makes voice recognition
more difficult.
•
C
onfirm that the correct voice commands are
being used. Glance at the screen to see the currently
available commands.
USING THE VOICE RECOGNITION SYSTEM
•
Press the
button 1 on the steering wheel, and a
list of commands will appear on the screen.
•
A
fter the tone sounds, speak the command.
•
T
o skip the voice prompt and give the command
immediately, press the
button 1 on the steering
wheel to interrupt the system. Speak the next
command after the tone sounds.
•
T
o cancel the command, press and hold the
button 1 on the steering wheel.
Please see your Owner’s Manual for important safety information, system
limitations, and additional operating and feature information.
Voice Recognition
1
PULLING UP THE WIPER ARM
The wiper arm should be in the UP
position when replacing the wiper.
•
With the shift le
ver in the
P (PARK) position, place
the ignition switch in the
OFF position.
•
Within 1 minut
e, push the
wiper switch to the MIST
position twice. The wiper
operation stops in mid-
operation and the wiper arm
can be pulled up.
•
T
o return the wiper arm, place
the wiper arm in the DOWN
position and operate the wiper
switch once.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating
and feature information.
2917603_18a_Q70_US_pQRG_051717.indd 145/17/17 2:27 PM
