2018 INFINITI Q60 COUPE recommended oil

Do not use excessive force.
9. Refill engine with recommended oil and
install the oil filler cap securely.
See “Capacities and recommended
fluids/lubricants” (P.10-2) for drain and
refill capacity. The drain and refill capa-
city depends on the oil temperature and
drain time. Use these specifications for
reference only. Always use the dipstick
to determine the proper amount of oil in
the engine.
10. Start the engine and check for leakage
around the drain plug and the oil filter.
Correct as required.
11. Turn the engine off and wait more than
15 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
After the operation
1. Install the engine undercover into posi-
tion as the following steps.
a. Pull the center of the small plastic clip
out.
b. Hold the engine undercover into posi-
tion.
c. Insert the clip through the undercover
into the hole in the frame, then push
the center of the clip in to lock the clip
in place.d. Install the other bolts that hold the
undercover in place. Be careful not to
strip the bolts or over-tighten them.
2. Lower the vehicle carefully to the
ground.
3. Dispose of waste oil and filter properly.
WARNING
.Prolonged and repeated contact with
used engine oil may cause skin cancer.
.Try to avoid direct skin contact with
used oil. If skin contact is made, wash
thoroughly with soap or hand cleaner
as soon as possible.
.Keep used engine oil out of reach of
children.When checking or replacement is required,
we recommend an INFINITI retailer for
servicing.
CAUTION
.It is recommended that you use only
Genuine NISSAN Matic S ATF. Do
not mix with other fluids.
.Using automatic transmission fluid
other than Genuine NISSAN Matic S
ATF may cause deterioration in dri-
veability and automatic transmission
durability, and may damage the
automatic transmission. Damage
caused by the use of fluid other than
as recommended is not covered by
the INFINITI new vehicle limited
warranty.
Do-it-yourself8-13
AUTOMATIC TRANSMISSION
FLUID (ATF)

The following descriptions are provided to
give you a better understanding of the
scheduled maintenance items that should
be regularly checked or replaced. The main-
tenance schedule indicates at which mile-
age/time intervals each item requires
service.
In addition to scheduled maintenance, your
vehicle requires that some items be checked
during normal day-to-day operation. Refer
to “General maintenance” (P.9-2).
Items marked with “*” are recommended by
INFINITI for reliable vehicle operation. You
are not required to perform maintenance on
these items in order to maintain the warran-
ties which come with your vehicle. Other
maintenance items and intervals are re-
quired.
When applicable, additional information can
be found in the “8. Do-it yourself” section of
this manual.
NOTE:
INFINITI does not advocate the use of non-
OEM approved aftermarket flushing sys-
tems and strongly advises against perform-
ing these services on an INFINITI product.
Many of the aftermarket flushing systems
use non-OEM approved chemicals or sol-
vents, the use of which has not been
validated by INFINITI.For recommended fuel, lubricants, fluids,
grease, and refrigerant, refer to “Capacities
and recommended fluids/lubricants” (P.10-
2) of this manual.
EMISSION CONTROL SYSTEM
MAINTENANCE
Drive belts*:
Check engine drive belts for wear, fraying or
cracking and for proper tension. Replace any
damaged drive belts.
Engine air filter:
Replace at specified intervals. When driving
for prolonged periods in dusty conditions,
check/replace the filter more frequently.
Engine coolant* (for VR30DDTT engine
models):
Replace coolant at the specified interval.
When adding or replacing coolant, be sure to
use only Genuine NISSAN Long Life Anti-
freeze/Coolant (blue) or equivalent with the
proper mixture. (Refer to “Engine cooling
system (for VR30DDTT engine models)”
(P.8-6) to determine the proper mixture for
your area.)
NOTE:
Mixing any other type of coolant or the use
of non-distilled water may reduce the
recommended service interval of the cool-
ant.Engine coolant* (for 2.0L turbo gasoline
engine models):
Replace coolant at the specified interval.
When adding or replacing coolant, be sure to
use only BASF Glysantin
®G48®or equiva-
lent with the proper mixture. (Refer to
“Engine cooling system (for 2.0L turbo
gasoline engine models)” (P.8-8) to deter-
mine the proper mixture for your area.)
NOTE:
Mixing any other type of coolant or the use
of non-distilled water may reduce the
recommended service interval of the cool-
ant.
Intercooler coolant (for VR30DDTT engine
models):
Intercooler coolant is maintenance-free.
Engine oil and oil filter:
Replace engine oil and oil filter at the
specified intervals. For recommended oil
grade and viscosity refer to “Capacities and
recommended fluids/lubricants” (P.10-2).
Engine valve clearance*:
Inspect only if valve noise increases. Adjust
valve clearance if necessary.
Evaporative emissions control vapor lines*:
Check vapor lines for leaks or looseness.
Tighten connections or replace parts as
necessary.
Maintenance and schedules9-5
EXPLANATION OF SCHEDULED
MAINTENANCE ITEMS

MAINTENANCE OP-
ERATION
Perform at number of
miles, kilometers or
months, whichever
comes first.Miles × 1,000
(km × 1,000)
MonthsMAINTENANCE INTERVAL
65
(104)
7870
(112)
8475
(120)
9080
(128)
9685
(136)
10290
(144)
10895
(152)
114100
(160)
120105
(168)
126110
(176)
132115
(184)
138120
(192)
144
Drive belts See NOTE (1) I* I* I* I* I* I*
Air cleaner filter See NOTE (2) R R
EVAP vapor lines I* I* I*
Fuel lines I* I* I*
Fuel filter See NOTE (3)
Engine coolant* See NOTE (4)
(5)
Engine oil See NOTE (6) R R R R R R
Engine oil filter See NOTE (6) R R R R R R
Spark plugs See NOTE (7) Replace every 105,000 miles (168,000 km)
Intake and exhaust valve
clearance*See NOTE (8)
NOTE:
(1) After 40,000 miles (64,000 km) or 48
months, inspect every 10,000 miles
(16,000 km) or 12 months. Replace the
drive belts if found damaged.
(2) If operating mainly in dusty conditions,
more frequent maintenance may be re-
quired.
(3) Periodic maintenance is not required.
(4) First replacement interval is 105,000
miles (168,000 km) or 84 months. Afterfirst replacement, replace every 75,000
miles (120,000 km) or 60 months.
(5) Use only Genuine NISSAN Long Life
Antifreeze/Coolant (blue) or equivalent
with proper mixture ratio of 50% anti-
freeze and 50% demineralized or distilled
water. Mixing any other type of coolant or
the use of non-distilled water may reduce
the life expectancy of the factory fill cool-
ant.
(6) If the oil replacement indicator is
displayed, change the engine oil and filteras soon as possible. After replacing the
engine oil, reset the display.
(7) Replace spark plug when the plug gap
exceeds 0.043 in (1.1 mm) even if within
specified replacement mileage.
(8) Periodic maintenance is not required.
However, if valve noise increases, inspect
valve clearance.
*: Maintenance items and intervals with “*”
are recommended by INFINITI for reliable
vehicle operation. The owner need not to
Maintenance and schedules9-9

9-12Maintenance and schedules
MAINTENANCE OP-
ERATION
Perform at number of
miles, kilometers or
months, whichever
comes first.Miles × 1,000
(km × 1,000)
MonthsMAINTENANCE INTERVAL
65
(104)
7870
(112)
8475
(120)
9080
(128)
9685
(136)
10290
(144)
10895
(152)
114100
(160)
120105
(168)
126110
(176)
132115
(184)
138120
(192)
144
Engine coolant* Replace every 120,000 miles (192,000 km) or 120 months
Engine oil R R R R R R
Engine oil filter R R R R R R
Spark plugs Replace every 45,000 miles (72,000 km) or 36 months
NOTE:
(1) All visible parts checked for leaks and
damage.
(2) In visible area only.
(3) Periodic maintenance is not required.
*: Maintenance items and intervals with “*”
are recommended by INFINITI for reliable
vehicle operation. The owner need not to
perform such maintenance in order to
maintain the emission warranty or manu-
facturer recall liability. Other maintenance
items and intervals are required.

10 Technical and consumer information
Capacities and recommended fluids/lubricants...... 10-2
Fuel information (for VR30DDTT
engine model)............................................................... 10-3
Fuel information (for 2.0L turbo gasoline
engine model)............................................................... 10-5
Engine oil and oil filter recommendation............ 10-8
Air conditioning system refrigerant and
lubricant recommendations .................................. 10-10
Specifications.................................................................. 10-11
Engine.......................................................................... 10-11
Wheels and tires ...................................................... 10-12
Dimensions ................................................................ 10-13
When traveling or registering in
another country............................................................. 10-14
Vehicle identification.................................................... 10-14
Vehicle Identification Number (VIN) plate ....... 10-14
Vehicle identification number
(chassis number) ...................................................... 10-14
Engine serial number .............................................. 10-15
F.M.V.S.S./C.M.V.S.S. certification label.......... 10-15
Emission control information label..................... 10-16
Tire and loading information label...................... 10-16
Air conditioner specification label ...................... 10-16Installing front license plate....................................... 10-17
Removing air deflectors............................................... 10-17
Vehicle loading information....................................... 10-18
Terms ........................................................................ 10-18
Vehicle load capacity............................................ 10-19
Loading tips ............................................................ 10-20
Measurement of weights.................................... 10-20
Towing a trailer............................................................. 10-21
Flat towing.............................................................. 10-21
Uniform tire quality grading...................................... 10-22
Treadwear ............................................................... 10-22
Traction AA, A, B and C...................................... 10-22
Temperature A, B and C...................................... 10-22
Emission control system warranty.......................... 10-23
Reporting safety defects............................................ 10-23
Readiness for Inspection/Maintenance (I/M)
test (US only)................................................................. 10-24
Event Data Recorders (EDR) .................................... 10-25
Owner’s Manual/Service Manual
order information ......................................................... 10-25

10-2Technical and consumer information
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure
instructed in the “8. Do-it-yourself” section to determine the proper refill capacity.
Fluid typeCapacity (approximate)
Recommended Fluids/Lubricants
Metric
MeasureUS
MeasureImperial
Measure
Fuel 76 L 20 gal 16-5/8 galÂSee “Fuel information (for VR30DDTT engine model)” (P.10-3) or “Fuel information (for
2.0L turbo gasoline engine model)” (P.10-5).
Engine oil
*1Drain and refill*1: For additional
information, see
“Engine oil” (P.8-
10).VR30DDTT
engine modelTwo-Wheel
Drive (2WD)
modelWith oil filter
change4.8 L 5-1/8 qt 4-1/4 qtÂGenuine “NISSAN Motor Oil 0W-20 SN” is recommended.
ÂIf the above motor oil is not available, use an equivalent motor oil that matches the above
grade and viscosity. For additional information, see “Engine oil and oil filter
recommendation” (P.10-8). Without oil fil-
ter change4.6 L 4-7/8 qt 4 qt
All-Wheel
Drive (AWD)
modelWith oil filter
change5.4 L 5-3/4 qt 4-3/4 qt
Without oil fil-
ter change5.2 L 5-1/2 qt 4-5/8 qt
2.0L turbo
gasoline en-
gine modelTwo-Wheel
Drive (2WD)
modelWith oil filter
change6.3 L 6-5/8 qt 5-1/2 qtÂEngine oil meeting specification MB229.5, viscosity SAE 0W-30 or equivalent.
ÂAs an alternative to this recommended oil, engine oils meeting specification MB229.5,
viscosity SAE 0W-40, 5W-30 and 5W-40 may be used and meet all specifications and
requirements necessary to maintain the new vehicle limited warranty.
ÂFor additional information, refer to “Selecting the correct oil” (P.10-9) and “Oil viscosity”
(P.10-9) under “Engine oil and oil filter recommendation” (P.10-8) of this manual. Without oil fil-
ter change5.8 L 6-1/8 qt 5-1/8 qt
All-Wheel
Drive (AWD)
modelWith oil filter
change6.6 L 7 qt 5-7/8 qt
Without oil fil-
ter change6.1 L 6-1/2 qt 5-3/8 qt
Engine coolant VR30DDTT
engine modelStandard and
premium
gradeTotal (with re-
servoir)8.8 L 9-1/4 qt 7-3/4 qtÂPre-diluted Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent
Reservoir 0.6 L 5/8 qt 1/2 qt
Sport grade Total (with re-
servoir)10.3 L 10-7/8 qt 9-1/8 qt
Reservoir 0.6 L 5/8 qt 1/2 qt
2.0L turbo
gasoline en-
gine modelTotal (with reservoir) 9.0 L 9-1/2 qt 7-7/8 qtÂBASF Glysantin
®G48®ÂUse BASF Glysantin®G48®or equivalent in its quality. Any damage to the vehicle or
within the engine cooling system caused by the use of engine coolant other than as
recommended is not covered under the INFINITI’s new vehicle limited warranty.
Reservoir 0.9 L 1 qt 3/4 qt
Intercooler coolant Total (with reservoir) 3.2 L 3-3/8 qt 2-7/8 qtÂPre-diluted Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent
Reservoir 0.4 L 3/8 qt 3/8 qt
CAPACITIES AND RECOMMENDED
FLUIDS/LUBRICANTS

Fluid typeCapacity (approximate)
Recommended Fluids/Lubricants
Metric
MeasureUS
MeasureImperial
Measure
Automatic Transmission Fluid (ATF) — — —ÂGenuine NISSAN Matic S ATF
ÂINFINITI recommends using Genuine NISSAN Matic S ATF ONLY in INFINITI automatic
transmissions. Do not mix with other fluids. Using fluids that are not equivalent to
Genuine NISSAN Matic S ATF may damage the automatic transmission. Damage caused
by the use of fluids other than as recommended is not covered under the INFINITI’s new
vehicle limited warranty.
Differential gear
oilFront — — —ÂGenuine NISSAN Differential Oil Hypoid Super GL-5 80W-90 or equivalent conven-
tional (non-synthetic) oil
Rear — — —ÂGenuine NISSAN Differential Oil Hypoid Super-S GL-5 synthetic 75W-90 or equivalent
Transfer fluid — — —ÂGenuine NISSAN Matic J ATF
ÂINFINITI recommends using Genuine NISSAN Matic J ATF ONLY in INFINITI transfers.
Do not mix with other fluids. Using fluids that are not equivalent to Genuine NISSAN
Matic J ATF may damage the transfer. Damage caused by the use of fluids other than as
recommended is not covered under the INFINITI’s new vehicle limited warranty.
Brake fluid Refill to the proper oil level according
to the instructions in the “8. Do-it-
yourself” section.ÂGenuine NISSAN Super Heavy Duty Brake Fluid
*4or equivalent DOT 3*4: Available in mainland U.S.A. through an INFINITI retailer.
Power steering fluidÂGenuine NISSAN E-PSF or equivalent
ÂUse of a power steering fluid other than Genuine NISSAN E-PSF may prevent the power
steering system from operating properly.
Multi-purpose grease — — —ÂNLGI No. 2 (Lithium soap base)
Air conditioning system refrigerant — — —ÂHFC-134a (R-134a)
For additional information, see “Vehicle identification” (P.10-14) for air conditioner
specification label.
Air conditioning system lubricants — — —ÂNISSAN A/C System Oil PAG or exact equivalent
Window washer fluid — — —ÂGenuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent
FUEL INFORMATION (for
VR30DDTT engine model)
Use unleaded premium gasoline with an
octane rating of at least 91 AKI (Anti-Knock
Index) number (Research octane number 96).
INFINITI recommends the use of unleaded
premium gasoline with 93 AKI number
(Research octane number 98) to obtain the
maximum vehicle performance and the best
driveability.If unleaded premium gasoline is not avail-
able, unleaded regular gasoline with an
octane rating of at least 87 AKI number
(Research octane number 91) may be tem-
porarily used, but only under the following
precautions:
.Have the fuel tank filled only partially
with unleaded regular gasoline, and fill
up with unleaded premium gasoline as
soon as possible..Avoid full throttle driving and abrupt
acceleration.
Use unleaded premium gasoline for max-
imum vehicle performance.
Technical and consumer information10-3

10-8Technical and consumer information
hicle checked. It is recommended you visit an
INFINITI retailer for servicing.
However, now and then you may notice
light spark knock for a short time while
accelerating or driving up hills. This is no
cause for concern, because you get the
greatest fuel benefit when there is light
spark knock for a short time under heavy
engine load.
JVT0342X
API certification mark
API service symbol
ENGINE OIL AND OIL FILTER
RECOMMENDATION
VR30DDTT engine model
Selecting the correct oil:
It is essential to choose the correct grade,
quality, and viscosity engine oil to ensure
satisfactory engine life and performance,
see “Capacities and recommended fluids/
lubricants” (P.10-2). INFINITI recommends
the use of an energy conserving oil in order
to improve fuel economy.Select only engine oils that meet the Amer-
ican Petroleum Institute (API) certification
or International Lubricant Standardization
and Approval Committee (ILSAC) certifica-
tion and SAE viscosity standard. These oils
have the API certification mark on the front
of the container. Oils which do not have the
specified quality label should not be used as
they could cause engine damage.
Oil additives:
INFINITI does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used
and maintenance intervals are followed.
Oil which may contain foreign matter or has
been previously used should not be used.