2018 HONDA CLARITY PLUG IN HYBRID start stop button

13
Quick Reference Guide
Auto Engine Stop/Start The car will select the appropriate source of power depending on the drive mode you select.
As a result, the engine will automatically start or stop as needed to either charge the battery or provide supplemental power.
Under certain circumstances, the engine may turn on or, if it is already on, it may not turn off.
● You are going uphill or accelerating aggressively.
● The climate control system is in heavy use.
● The Ambient temperature is too hot or too cold.
● The High Voltage Battery state of charge is very low.
● The vehicle is running a system check.
System Check When the engine initially starts (between the time the POWER button is turned on and turned of f), the vehicle conducts a system check.
● While the check is being conducted, the engine may periodically turn on and off. This, however, is normal.
● The curved blue line in the POWER / CHARGE Gauge will not appear during the system check ( EV indicator may still turn on).
● Once the engine starts, it will continue to run until the system reaches operating temperature.
The curved blue line in the POWER / CHARGE Gauge will reappear once the system check is completed.
2 POWER/CHARGE Gauge (P122)18 CLARITY PHEV CSS-31TRW6000.book 13 ページ ２０１７年８月３１日　木曜日　午後２時 ４９分

103uu Indicators u Driver Information Interface Wa rning and Information Messages
Continued
Instrument Panel
Driver Information Interface Warning and Information Messages The following messages appear only on the dr iver information interface. Press the (d isplay/information) button to see the mess age
again with the system message indicator on.
Message Condition Explanation●
Appears when the vehicle cannot be driven. ●
Immediately stop in a safe place.●
Appears when the washer fluid gets low. ●
Refill the washer fluid. 2 Refilling Window Washer Fluid P. 493●
Appears when the scheduled maintenance is due
soon. ●
Consequently, Service Due Now and Service Past
Due follow. 2 Warning Message and Maintenance Minder
Information on the Driver Information Interface
P. 476●
Appears as soon as a problem is detected in the
smart entry system or push button starting system. ●
Appears constantly - Have your vehicle checked by an
authorized Honda Clarity Plug-In Hybrid dealer.Canadian models18 CLARITY PHEV CSS-31TRW6000.book 103 ページ ２０１７年８月３１日　木曜日　午後２時４９分

uu When Driving u Turning on the Power
378
Driving You can turn the power system off when the vehicle is completely stopped.
1. Put the transmission into ( P
.
2. Press the POWER button.
■ Stopping the Power System 1 Turning on the Power
Bring the smart entry remote close to the POWER
button if the battery in the smart entry remote is
weak.
2 If the Smart Entry Remote Battery is Weak
P. 537
The power system may not activate if the smart entry
remote is subjected to strong radio waves.
Do not hold the POWER button to start the power
system.
If the power system does not start, wait at least 30
seconds before trying again.18 CLARITY PHEV CSS-31TRW6000.book 378 ページ ２０１７年８月３１日　木曜日　午後２時４９分

Continued
405uu When Driving u Adaptive Cruise Control (ACC) with Low Speed Follow (LSF)
Driving
■ There is no vehicle ahead
Your vehicle maintains the set speed without
having to keep your foot on the brake or
accelerator pedal.
If there previously was a vehicle detected
ahead that kept your ve hicle from traveling at
the set speed, ACC with LSF accelerates your
vehicle to the set speed, and then maintains it.
■ When you depress the accelerator pedal
You can temporarily increase the vehicle speed . In this case, there is no audible or
visual alert even if a vehicl e is in the ACC with LSF range.
ACC with LSF stays on unless you cancel it . Once you release th e accelerator pedal,
the system resumes an appropriate speed fo r keeping the followi ng-interval while a
vehicle ahead is within the ACC with LSF range.
■ A vehicle detected ahead is within ACC with LSF range and slows to a stop
Your vehicle also stops, automatically. The
Stopped message appears on the driver
information interface.
When the vehicle ahead of you starts again,
the vehicle icon on the driver information
interface blinks. If you press the RES/+ or
−/SET button, or depress the accelerator
pedal, ACC with LSF operates again within the
prior set speed. 1 When in Operation
Limitations
You may need to use the brake to maintain a safe
interval when using ACC wi th LSF. Additionally, ACC
with LSF may not work properly under certain
conditions.
2 ACC with LSF Conditions and Limitations
P. 4063
WARNING Exiting a vehicle that has been stopped
while the ACC with LSF system is operating
can result in the ve hicle moving without
operator control.
A vehicle that moves without operator
control can cause a crash, resulting in
serious injury or death.
Never exit a vehicle when the vehicle is
stopped by ACC with LSF.A vehicle icon with dotted-line
contour appears on the driver
information interface
1 When you depress the accelerator pedal
While the accelerator pedal is depressed, the system
does not apply the brakes to keep the following
interval, as well as the BRAKE message on the driver
information interface does not appear.18 CLARITY PHEV CSS-31TRW6000.book 405 ページ ２０１７年８月３１日　木曜日　午後２時４９分

Continued
435 uu Braking u Brake System
Driving
Keeps the brake applied after releasing the brake pedal until the accelerator pedal is
pressed. You can use this system while th e vehicle is temporarily stopped, like at
traffic lights and in heavy traffic.
■ Automatic Brake Hold 1 Automatic Brake Hold
3
WARNING Activating the automatic brake hold system
on steep hills or slippery roads may still
allow the vehicle to move if you remove
your foot from the brake pedal.
If a vehicle unexpectedly moves, it may
cause a crash resulting in serious injury or
death.
Never activate the automatic brake hold
system or rely on it to keep a vehicle from
moving when stopped on a steep hill or
slippery roads.
3
WARNING Using the automatic brake hold system to
park the vehicle may result in the vehicle
unexpectedly moving.
If a vehicle moves unexpectedly, it may
cause a crash, resulting in serious injury or
death.
Never leave the vehicl e when braking is
temporarily kept by automatic brake hold
and always park the vehicle by putting the
transmission in ( P
and applying the parking
brake.■ Turning on the system
Fasten your seat belt
properly, then start the
power system. Press the
automatic brake hold
button. ●
The automatic brake
hold system indicator
comes on. The system
is turned on. ■ Activating the system
Depress the brake pedal
to come to a complete
stop. The transmission
must be in ( D
or ( N
. ●
The automatic brake
hold indicator comes
on. Braking is kept for
up to 10 minutes. ●
Release the brake
pedal after the
automatic brake hold
indicator comes on. ■ Canceling the system
Depress the accelerator
pedal while the
transmission is in ( D
.
The system is canceled
and the vehicle starts to
move. ●
The automatic brake
hold indicator goes
off. The system
continues to be on. Accelerator Pedal
Brake PedalAutomatic Brake
Hold Button Goes
OffComes
On On On
Comes
On
Comes
OnU.S.
Canada18 CLARITY PHEV CSS-31TRW6000.book 435 ページ ２０１７年８月３１日　木曜日　午後２時４９分

452 uu Refueling u How to Refuel
Driving How to Refuel 1. Stop your vehicle with the service station
pump on the left side of the vehicle in the
rear.
2. Put the transmission into ( P
.
3. Turn the power system off.
4. Press the fuel fill door release button.
u Please Wait appears for a few seconds
on the driver information interface.
5. When the message changes to Ready , the
fuel fill door automatically opens.
u You can now unscrew the fuel cap and
start refueling.
6. Remove the fuel fill cap slowly. If you hear a
release of air, wait unt il this stops, then turn
the knob slowly to open the fuel fill cap. 1 How to Refuel
This vehicle has a pressurized fuel system.
When the fuel vapor pressure inside the fuel tank is
high, it takes about 10 seconds for the vehicle to vent
the fuel tank. Once the pressure is vented, the driver
information interface changes from Please Wait to
Ready .
If the filler nozzle keeps tu rning off when the tank is
not full, there may be a problem with the pump's fuel
vapor recovery system. Try fi lling at another pump. If
this does not fix the problem, consult an authorized
Honda Clarity Plug-In Hybrid dealer.
Do not continue to add fuel after the filler nozzle has
automatically stopped. Addi tional fuel can exceed
the full tank capacity.
The filler nozzle automatically stops to leave space in
the fuel tank so that fuel does not overflow as a result
of changes in air temperature.3
WARNING Gasoline is highly flammable and explosive.
You can be burned or seriously injured
when handling fuel.
• Stop the engine, and keep heat, sparks,
and flame away.
• Handle fuel only outdoors.
• Wipe up spills immediately.Fuel Fill Door
Release Button
Fuel Fill Cap18 CLARITY PHEV CSS-31TRW6000.book 452 ページ ２０１７年８月３１日　木曜日　午後２時４９分

Continued
459uu Charging u Charge the High Voltage battery using a Level 1 or 2 charger
Driving
1. Stop your vehicle at a station specified for
electric vehicles. Park with the charge lid
closest to the charge plug, just in front of
the driver’s door.
2. Put the transmission into ( P
.
3. Turn off the power system.
4. Press and hold the charge lid release
button.
u The lid opens.
The illumination lamp inside the charge lid
comes on for a few minutes.■ How to Charge (Level 2) 1 Charge the High Voltage battery using a Level 1 or 2 charger
The High Voltage battery may not be charged even if
the charging connector is properly connected to the
vehicle’s inlet when the charging timer is set but the
timer has not yet started.
To avoid damage to th e charger, take these
precautions:
• Do not hit the charging connector components
with a hard object or drop them on the ground.
• Do not pull, twist, tangle, drag or step on the
charging cable.
• Do not use or store near any sources of heat.
• Do not expose to liquids or use harsh chemicals to
clean.
If you unplug the charging connector from the inlet,
charging cancels automatically.
The charge speed slows down towards the
completion of the battery charging. When the High
Voltage battery temperature is low, the charge speed
may slow or it may not be fully charged.Charge Lid
Release
Button18 CLARITY PHEV CSS-31TRW6000.book 459 ページ ２０１７年８月３１日　木曜日　午後２時４９分

538 uu Power System Won’t Start u Emergency Power System Off
Handling the Unexpected Emergency Power System Off The POWER button may be used to turn the po wer system off due to an emergency
situation even while dr iving. If you must turn the powe r system off, do either of the
following operations:
• Press and hold the POWER button for about two seconds.
• Firmly press the POWER button three times.
The steering wheel will not lock. However, because turning off the power system
disables the power assist the power syst em provides to the steering and braking
systems, it will require significantly more physical effort and time to steer and slow
the vehicle. Use both feet on the brake pe dal to slow down the vehicle and stop
immediately in a safe place.
The gear position auto matically changes to ( P
after the vehicle comes to a complete
stop. Then, the power mode changes to VEHICLE OFF. 1 Emergency Power System Off
Do not press the button while driving unless it is
absolutely necessary for the power system to be
turned off.18 CLARITY PHEV CSS-31TRW6000.book 538 ページ ２０１７年８月３１日　木曜日　午後２時４９分