2018 FIAT 500 lights

SAFETY
102
Press button C fig. 67 to release the
belt.
Guide the belt while it is rewinding to
prevent it from twisting.
The retractor may lock when the
vehicle is parked on a steep slope: this
is perfectly normal.
Furthermore, the reel mechanism locks
the belt if it is pulled sharply or in the
event of sudden braking, collisions and
high-speed bends.
The rear seat is fitted with inertia seat
belts with three anchor points and a
retractor.
NOTE Wear the rear seat belts as
shown in fig. 68.
67DVDF0S041c
IMPORTANT When putting the seats
back to their normal position, make
sure the seat belts are positioned so
they are ready to use.
SBR SYSTEM
(for versions/markets, where provided)
The SBR system warns the
passengers of the front and rear (for
versions/markets, where provided)
seats if their seat belt is not fastened.
The system signals unfastened seat
belts with visual warnings (warning
lights on in the instrument panel and
icons on the display) and an acoustic
signal (see the following paragraphs).
NOTE Contact a Fiat Dealership to
deactivate this acoustic warning
permanently. The acoustic warning can
be reactivated at any time through the
display Setup Menu.
68DVDF0S0056c
Seat belts warning
light operation
The system warns the driver and the
front passenger if their seat belt is not
fastened, as follows:
❒ flashing
intermittent acoustic warning for
about 100 seconds.
❒ once the cycle has finished, the
warning light remains on constantly
until the seat belts are fastened.
PRE-TENSIONERS
The car is equipped with front seat belt
pretensioners, which in the event of a
major frontal impact guarantee the
perfect adherence of the seat belts to
the occupant’s bodies before the
retention action begins.

119
ENGINE STARTING
fig. 85 26) 13)
Petrol versions (excluding 0.9
TwinAir 105 HP)
❒ engage the handbrake;
❒ gear in neutral;
❒ fully press the clutch pedal without
touching the accelerator;
❒ turn the key to AVV and release it as
soon as the engine starts.
0.9 TwinAir 105 HP versions
❒ engage the handbrake;
❒ gear lever in neutral or fully press
the clutch pedal if a gear other than
neutral is engaged;
❒ turn the key to AVV and release it as
soon as the engine starts.
Diesel versions
❒ engage the handbrake;
❒ gear in neutral;
❒ turn the key to MAR and wait for the
warning lights or symbols
mand
to turn off;
❒ push the clutch pedal fully;
❒ turn the key to AVV and release it as
soon as the engine starts.
LPG versions
The engine always starts up on petrol
independently of the previously
selected mode. Therefore, there must
always be enough petrol in the tank.
STARTING AND DRIVING
Versions with Dualogic gearbox
The system allows the engine to be
started both with a gear engaged and
with the gearbox in neutral (N).
However, the brake pedal must always
be pressed first if neutral is not
engaged. It is therefore advisable to
position the gear lever at N before
starting the engine.
85DVDF0S057c

131
“Fix&Go” KIT
33) 31)
DESCRIPTION
The Fix&Go quick tyre repair kit fig. 105
is located in the luggage compartment,
inside a dedicated container, and
consists of:
❒ one cartridge 1 containing sealant
and fitted with: transparent tube for
injecting the sealant 4 and sticker 3
with the wording “Max 80 km/h” to
be placed in a clearly visible position
(e.g. on the dashboard) after
repairing the tyre;
❒ one compressor 2;
❒ one leaflet containing instructions
for using the kit;
❒ a pair of gloves located in the hose
compartment of the cartridge 4.
REPAIR PROCEDURE
Proceed as follows:
❒ stop the car in a position that is not
dangerous for oncoming traffic
where you can carry out the
procedure safely. The ground must
be flat and sufficiently compact;
❒ stop the engine, engage the hazard
warning lights and the parking
brake;
❒ wear the reflective safety jacket
before getting out of the car (in any
case, comply with the laws in force
in the country you are driving in);
105DVDF0S0230
❒ insert the cartridge 1 containing the
sealant into the dedicated
compartment on the compressor 2
and press it down hard fig. 105.
Remove the adhesive speed label 3
and apply it in a clearly visible
position fig. 106;
❒ wear the gloves;
❒ remove the valve cap from the
punctured tyre and screw the
transparent sealant hose 4 fig. 105
onto the valve. If a 250 ml cartridge
is present the housing of the
transparent tube is provided with
removable ring to facilitate
extraction. Make sure that the
ON-OFF button 5 fig. 107 is in the
off position (button not pressed);
106DVDF0S0234

IN AN EMERGENCY
134
REPLACING A BULB
34) 19)
GENERAL
INSTRUCTIONS
❒ Before changing a bulb check the
contacts for oxidation;
❒ burnt bulbs must be replaced by
others of the same type and power;
❒ always check the headlight beam
aiming after changing a bulb;
❒ whenever a lamp does not work,
please check that the
corresponding fuse is in tact before
replacing it: please refer to the
paragraph “Replacing fuses” in this
chapter for the location of fuses.
IMPORTANT Whenever the weather is
hot or cold, of after heavy rain, the
surface of the headlights or rear lights
may steam up and/or form droplets of
condensation on the inside. This is a
natural phenomenon due to the
difference in temperature and humidity
between the inside and the outside of
the glass which does not indicate a
fault and does not compromise the
normal operation of lighting devices.
The mist disappears quickly when the
lights are turned on, starting from the
centre of the diffuser, extending
progressively towards the edges.

135
TYPES OF BULBS
BulbsTypePower
Main beam headlights H7 55W
Dipped beam headlights H7 55W
Xenon gas discharge dipped beam headlights D1S 35W
Side lights / daytime running lights W21W / LL 5W / 21W
Front direction indicators PY24W / WY21W 21W
Front direction indicators (with xenon gas discharge bulbs) PY24W 24W
Side direction indicators W5W 5W
Rear direction indicators PY21W 21W
Tail lights/brake lights P21 / 5W 10W
Reversing light, rear fog light W16W 21W
Ceiling light C5W 5W
Luggage compartment ceiling light W5W 5W
Number plate C5W 5W
Fog light H3 55W
Additional stop (3rd braking) W5W 5W

IN AN EMERGENCY
136
FRONT LIGHT CLUSTERS
The front light clusters contain side
lights, dipped headlights, main beam
headlights and direction indicator bulbs.
Access to the direction indicator
bulbs (POP versions)
Operating from the engine
compartment, remove the rubber cap
A fig. 111.
Access to the main beam headlight
bulbs (POP versions)
Remove the rubber cap B fig. 111.
111DVDF0S0114c
Access to the direction indicator
bulbs (excluding POP versions)
Operating from the engine
compartment, remove the rubber cap
A fig. 112.
Access to the main beam headlight
bulbs (excluding POP versions)
Operating from the engine
compartment, remove the rubber cap
B fig. 112.
112DVDF0S0196c
Access to the daytime running light
(DRL) and main beam headlight
bulbs
Completely steer the wheels and open
guard door C fig. 113 (on the wheel
arch at the level of the lights) then
remove the rubber cap D.
113DVDF0S0115c

137
MAIN BEAM
HEADLIGHTS
(POP versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ press the fastener A fig. 114 and
remove the bulb holder;
❒ remove the snap-fitted bulb and
replace it;
❒ refit the bulb holder locking it
properly;
❒ reinstall the rubber cap.
114DVDF0S0118c
MAIN BEAM
HEADLIGHTS
(Excluding POP
versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ disconnect the central electric
connector A fig. 115 and
and release
the bulb holder catch A;
❒ remove the bulb and replace it;
❒ refit the bulb in its seat and
reconnect the connector;
❒ refit the protection cap in its housing
and turn clockwise.
With gas discharge bulbs (Xenon)
(for versions/markets, where provided)
Contact a Fiat Dealership.
115DVDF0S0197c
MAIN BEAM
HEADLIGHTS
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ release the two bulb holding clips A
fig. 116;
❒ remove the bulb and replace it;
❒ fit the new bulb, making the outline
of the metallic part coincide with the
grooves on the reflector, then hook
back the bulb holding clips;
❒ reinstall the rubber cap.
116DVDF0S0119c

IN AN EMERGENCY
138
SIDE LIGHTS / DAYTIME
RUNNING LIGHTS
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder B fig. 116
anticlockwise and remove it;
❒ remove the snap-fitted bulb and
replace it;
❒ refit the bulb holder B by turning it
clockwise and locking it correctly;
❒ reinstall the rubber cap.
DIRECTION INDICATORS
Front (POP versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder A fig. 117
anticlockwise and pull it out;
❒ remove the snap-fitted bulb and
replace it;
❒ refit the bulb holder A by turning it
clockwise and locking it correctly;
❒ reinstall the rubber cap.
117DVDF0S0116c
Front (Excluding POP versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder anticlockwise
and remove it;
❒ replace the bulb
bulb holder assembly;
❒ refit the bulb holder in its housing
A fig. 118 by turning it clockwise
and locking it correctly;
❒ refit the protection cap in its housing
and turn anticlockwise.
118DVDF0S0198c