2018 DODGE CHALLENGER SRT wheel

RECOMMENDATIONS FOR SAFE TIRE INFLATION
•If you must inflate your tires when they are hot, add 4 pounds per
square inch (4 psi) (28 kPa) above the recommended inflation pressure
specification. Recheck the inflation pressure when the tires are cold
and adjust to the recommended inflation pressure shown on the
vehicle’s Tire Information Placard.
•Never release air or nitrogen from a hot tire in order to reach the
recommended cold tire pressure. Normal driving causes tires to run
hotter and inflation pressure to increase. If you release pressure when
your tires are hot, you may dangerously underinflate your tires. If your
tires lose more than 1 pound per square inch (1 psi) per month, the tire,
the valve, or the wheel may be damaged. Consult your authorized
Nitto dealer for an inspection.
•Over-inflation can cause the tire to be more susceptible to impact
damage.
•Over-inflation or underinflation may adversely affect vehicle
handling.
•Remember to check your spare tire. Consult your vehicle Owner ’s
Manual for the correct inflation pressure and use of a “temporary use”
spare tire. The inflation pressure specified for a spare tire is typically
different from that specified for your regular tires.
•Use valve caps to keep valve cores clean and clear of debris and to help
guard against air leakage.
WARNING!
Never inflate a tire unless it is secured to the vehicle or a tire
mounting machine. Inflating an unsecured tire is dangerous. If the
tire bursts, it could be propelled into the air with explosive force
and cause serious personal injury or death.
NITTO TIRE
282

VEHICLES EQUIPPED WITH TIRE PRESSURE MONITORING
SYSTEMS (TPMS)
Even if your vehicle is equipped with a tire pressure
monitoring system, you should check your tire pres-
sure at least once per month when the tires are cold
(for example, after being parked overnight). Tire pres-
sure warning systems are not a substitute for regular
tire pressure maintenance.
WARNING!
If your vehicle is equipped with TPMS, read the vehicle Owner ’s
Manual regarding its operation. Some TPMS systems do not alert you
until the tires are significantly underinflated, which could result in
permanent tire damage and possible sudden tire failure. In the event
that your TPMS malfunction indicator lamp is displayed, you should
immediately pull over to a safe parking area and check your tires.
IDENTIFYING DAMAGED TIRES
•If your tire strikes a road hazard at any speed, internal tire damage
could result, which may lead to sudden tire failure and loss of vehicle
control. Tire failure may even occur miles after the initial impact.
Impact damage from such hazards may not be visible on the outside of
the tire. Have your Nitto dealer dismount the tire and inspect it for
damage. A tire may not have visible signs of damage on the tire surface
or the interior.
•If the impact was sufficient to bend the wheel flange, internal tire
damage may have occurred, compromising the safety and integrity of
the tire. Such impact damage may result in a sudden tire failure many
weeks or months later. Tire replacement is highly recommended as a
safety precaution.
•Indications of impact damage include, but are not limited to, a bubble
or a blister on the outside of the tire.
•Have your dealer inspect your tires if you see anything unusual or if
cuts, cracks, splitting, or bruises in the tread and sidewall areas are
visible. Bumps or bulges may indicate a serious and dangerous
separation within the tire body. Have your tire inspected by a qualified
tire service person. It may be necessary to have the tire removed from
the wheel for a complete inspection.
NITTO TIRE
283

•Inspect your tires for adequate tread depth. When the tire is worn to
the built-in indicators at 2/32” (1.6 mm) or less tread groove depth, the
tire is worn out and must be replaced. Never drive on tires to the point
that the tire cord or the fabric is exposed.
•Inspect your tires for uneven wear. Wear on one side of the tread or flat
spots in the tread may indicate alignment or other problems with the
tires or the vehicle. Consult your authorized Nitto dealer.
WARNING!
Never drive on a tire if there is any evidence of damage. Driving on
a damaged tire is dangerous. A damaged tire could suddenly fail,
which may result in loss of vehicle control and lead to serious
personal injury or death. Do not attempt to dismount, mount, or
repair a tire yourself. See your Nitto dealer immediately if you
detect damage.
IDENTIFYING DAMAGED WHEELS
Periodically check to see if any of the following symptoms exist, in which
case the wheel must be replaced:
•If the flange is bent.
•If welds or rivets are leaking.
•If the stud holes are elongated and not round. (Improper lug nut
tightening could cause this.)
•If there are cracks in the wheel.
WORN OUT TIRES
Tires must be replaced when tread is worn to 2/32” (1.6 mm). Treadwear
indicators on Nitto tire treads show the 2/32” depth (1.6 mm). Most
states require that tires be replaced when the tread depth is worn to 2/32”
(1.6 mm). Tires may lose sufficient wet and snow traction before reaching
2/32” (1.6 mm) of wear. Many wet weather accidents result from
skidding on worn out tires.
Excessively worn tires are more susceptible to penetrations. Consider
replacing your tires earlier if you drive in snow or wet conditions.
NITTO TIRE
284

•Do not use a rope type plug for repair. A tire must be removed from the
wheel and inspected for interior damage. Any tire repair done without
removing the tire from the wheel is improper and unsafe.
•Never repair a tire with a puncture or other damage outside the tread
area. Do not repair sidewall damage. Such tires cannot be properly
repaired and must be replaced.
“See illustration on next page”
NITTO TIRE
286

WARNING!(Continued)
Certain vehicle performance parameters, including ride comfort and
handling, may be affected by substitute tire sizes. In some cases,
particularly for SUVs and light trucks, a failure to follow the vehicle
manufacturer ’s recommendations for tire replacement could
adversely affect the safe handling of the vehicle, possibly resulting
in a loss of vehicle control leading to personal injury or death.
The following procedures concerning replacement tires must be fol-
lowed:
•Confirm that the load-carrying capacity is greater than or equal to the
load-carrying capacity of the OE tire size at the pressure indicated on
the vehicle Tire Information Placard.
•Carefully note any differences between recommendations for front and
rear axle positions regarding the tire size and/ or inflation pressure.
•The speed rating must be equal to or greater than what is specified by
the vehicle manufacturer if the speed capability of the vehicle is to be
maintained.
•Tires should be mounted on approved wheel widths. If changing tire
sizes, check to make sure the wheel has adequate load and inflation
pressure capacity.
•Body and chassis clearance must be checked on the vehicle’s front and
rear axles.
In addition to the above, light truck tire replacements should take into
consideration the following:
•Proper spacing between dual tires is necessary for optimum tire
performance. If chains are used, particular care must be taken to assure
adequate clearance between loaded tires to avoid damage from the
chains. The allowable outside diameter difference between a tire and
its dual mate is ¼” (6.4 mm) for light truck tires.
CONSIDERATIONS IN PLUS SIZING
Always refer to and follow the vehicle manufacturer ’s replacement tire
recommendations. In some cases, a vehicle manufacturer may specifically
advise against the application of replacement tires that are not of the
original size or type.
NITTO TIRE
289

TIRE AND WHEEL MATCHING AND MOUNTING
WARNING!
Any attempt to mount a tire on a wheel with a different diameter
will result in an explosion of the tire/wheel assembly that could
cause severe personal injury or death.
Prior to mounting any tire, always check the wheel identification
stamp to verify the correct wheel diameter. Always check the tire
size molded onto the sidewall.
Never exceed 40 psi when seating the tire beads onto the wheel.
Always stand well clear of any tire mounting operation. This is
especially important when the service operator inflates the tire. If
the tire has been improperly mounted, it could burst with explosive
force causing serious personal injury or death.
A new valve stem must be installed on the wheel each time a
worn-out passenger or light truck tire is replaced.
Removing and replacing tires on wheels can be dangerous.
Attempting to mount tires with improper tools or procedures could
result in a tire explosion, causing serious personal injury or death.
This is a job for your authorized Nitto dealer or other qualified tire
service location only.
Serious personal injury or death can result from:
•Failure to select the proper tire and wheel. The tire must match the
width and diameter requirements of the wheel. When mounting
truck type radial tires use only wheels approved for radial tires.
•Failure to inspect both the tire and wheel. The wheel must be free
of cracks, dents, chips, and rust. The tire must be free of bead
damage, cuts, and punctures.
•Failure to follow proper procedures. For proper mounting proce-
dures, consult the Rubber Manufacturers Association’s publication
“Care and Service of Automobile and Light Truck Tires” (ref.:
www.rma.org).
•Exceeding the maximum bead seating pressure of 40 psi. Be
absolutely certain beads are fully seated before adjusting the
inflation pressure to the level recommended for vehicle operation.
Never put flammable substances in the tire/wheel assemblies at any
time. Never put any flammable substance into a tire/wheel assembly
and attempt to ignite it in order to seat the beads.
NITTO TIRE
290

FOUR-WHEEL DRIVE (4WD) AND ALL-WHEEL DRIVE (AWD)
VEHICLES
If no instructions for tire mixing appear in the vehicle Owner ’s Manual,
follow these guidelines:
•Do not mix tire sizes. All four tires must be marked with the same tire
size, unless otherwise specified by the vehicle manufacturer. This also
applies to winter/snow tires.
•Do not mix tread pattern types such as all-terrain and all- season.
STUDLESS WINTER/SNOW TIRES
•It is always preferable to apply winter/snow tires to all wheel
positions, including dual tires, to maintain vehicle mobility and
control.
•If winter/snow tires are applied to the front axle of any vehicle,
winter/snow tires must also be installed on the rear axle. DO NOT
apply winter/snow tires only to the front axle. This applies to all
passenger and light truck vehicles, including front-wheel- drive, 4WD,
and AWD vehicles.
•If winter/snow tires are installed on the rear axle of any vehicle, it is
recommended (but not required) that they also be installed on the front
axle.
WARNING!
Unless winter/snow tires on the rear axle have comparable traction
qualities to the tires on the front axle, the vehicle may experience
adverse handling characteristics. This may result in loss of vehicle
control, which can lead to serious personal injury or death.
STUDDED WINTER/SNOW TIRES
•Studded winter/snow tires have higher traction qualities under most
winter weather conditions.
•If studded winter/snow tires are installed on the front axle of any
vehicle, studded winter/snow tires must also be installed on the rear
axle. DO NOT apply studded winter/snow tires only to the front axle.
•If studded winter/snow tires are installed on the rear axle of any
vehicle, it is strongly recommended that they should also be installed
NITTO TIRE
292

on the front axle. Only if studded winter/snow tires are installed on all
wheel positions of a vehicle will optimum handling characteristics be
achieved.
WARNING!
Installing only two studded winter/snow tires on the front axle of
any vehicle (including front-wheel-drive vehicles) without studded
winter/snow tires on the rear axle can cause adverse vehicle
handling characteristics. This can result in a loss of vehicle control,
which could cause serious personal injury or death.
mNOTICE!
In some cases, the vehicle manufacturer may specifically advise against
replacing fewer than all four tires. Always check and follow the
recommendations in the vehicle Owner’s Manual. For 4WD and AWD
vehicles, even small differences in outside diameter may cause drivetrain
damage or mechanical malfunction.
REPLACING TWO TIRES
•When a pair of replacement tires is selected in the same size and
construction as those on the vehicle, the two newer tires must be
installed on the rear axle and must be of equal or higher speed rating
than the front tires. Generally, new tires with deeper tread will provide
better grip and evacuate water more effectively, which is important as
a driver approaches hydroplaning situations. Placing greater traction
on the rear axle on wet surfaces is necessary to prevent a possible
oversteer condition and loss of vehicle stability.
•When two new tires have been installed onto the rear axle positions,
they are to be kept on the rear but rotated from side to side. This is
recommended after installing two new tires to the rear position, or if
you discover significant tread depth differences between the front and
rear positions during rotation intervals.
NITTO TIRE
293