2018 DODGE CHALLENGER SRT garage door opener

HOOD ................................80
▫ To Open The Hood ......................80
▫ To Close The Hood ......................81
 TRUNK ...............................81
▫ Opening .............................81
▫ Closing ..............................83
▫ Trunk Safety ...........................83
 GARAGE DOOR OPENER — IF EQUIPPED .....84
▫ Before You Begin Programming HomeLink .....84▫
Canadian/Gate Operator Programming ........87
▫ Using HomeLink ........................88
▫ Security ..............................89
▫ Troubleshooting Tips .....................89
▫ General Information ......................90
 INTERNAL EQUIPMENT ...................90
▫ Storage ...............................90
▫ Cupholders ............................92
▫ Electrical Power Outlets ..................93
16 GETTING TO KNOW YOUR VEHICLE

GARAGE DOOR OPENER — IF EQUIPPED
HomeLink replaces up to three hand-held transmitters that
operate devices such as garage door openers, motorized
gates, lighting, or home security systems. The HomeLink
unit is powered by your vehicle’s battery.
The HomeLink buttons that are located in the overhead
console designate the three different HomeLink channels.
The HomeLink indicator is located on the left side of the
first button.
NOTE:HomeLink is disabled when the Vehicle Security
Alarm is active.
Before You Begin Programming HomeLink
Be sure that your vehicle is parked outside of the garage
before you begin programming.
For more efficient programming and accurate transmission
of the radio-frequency signal it is recommended that a new
battery be placed in the hand-held transmitter of the device
that is being programmed to the HomeLink system.
To erase the channels, place the ignition in the ON/RUN
position, and push and hold the two outside HomeLink
buttons (I and III) for up to 20 seconds or until the orange
indicator flashes.
NOTE:
• Erasing all channels should only be performed when
programming HomeLink for the first time. Do not erase
channels when programming additional buttons.
• If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
HomeLink Buttons
84 GETTING TO KNOW YOUR VEHICLE

Programming A Rolling Code
For programming garage door openers that were manufac-
tured after 1995. These garage door openers can be identi-
fied by the “LEARN” or “TRAIN” button located where
the hanging antenna is attached to the garage door opener.
NOTE:It is NOT the button that is normally used to open
and close the door. The name and color of the button may
vary by manufacturer.
1. Place the ignition in the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Push and hold the HomeLink button you want to program while you push and hold the hand-held trans-
mitter button.
Training The Garage Door Opener
1 — Door Opener
2 — Training Button
3
GETTING TO KNOW YOUR VEHICLE 85

4. Continue to hold both buttons and observe the indicatorlight. The HomeLink indicator will flash slowly and
then rapidly after HomeLink has received the frequency
signal from the hand-held transmitter. Release both
buttons after the indicator light changes from slow to
rapid.
5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually
be found where the hanging antenna wire is attached to
the garage door opener/device motor. Firmly push and
release the “LEARN” or “TRAINING” button. On some
garage door openers/devices there may be a light that
blinks when the garage door opener/device is in the
LEARN/TRAIN mode.
NOTE: You have 30 seconds in which to initiate the next
step after the LEARN button has been pushed.
6. Return to the vehicle and push the programmed HomeLink button twice (holding the button for two
seconds each time). If the garage door opener/device
activates, programming is complete.
NOTE: If the garage door opener/device does not activate,
push the button a third time (for two seconds) to complete
the training. To program the remaining two HomeLink buttons, repeat
each step for each remaining button. DO NOT erase the
channels.
Reprogramming A Single HomeLink Button (Rolling
Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink button until the
indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button proceed with “Program- ming A Rolling Code” step 2 and follow all remaining
steps.
Programming A Non-Rolling Code
For programming Garage Door Openers manufactured
before 1995.
1. Cycle the ignition to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
86 GETTING TO KNOW YOUR VEHICLE

2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Continue to press and hold the HomeLink button, while you press and release (“cycle”) your hand-held trans-
mitter every two seconds until HomeLink has success-
fully accepted the frequency signal. The indicator light
will flash slowly and then rapidly when fully trained.
4. Watch for the HomeLink indicator to change flash rates. When it changes, it is programmed. It may take up to 30
seconds or longer in rare cases. The garage door may
open and close while you are programming.
5. Press and hold the programmed HomeLink button and observe the indicator light.
NOTE: •If the indicator light stays on constantly, programming
is complete and the garage door/device should acti-
vate when the HomeLink button is pressed.
• To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels. If you unplugged the garage door opener/device for
programming, plug it back in at this time.
Reprogramming A Single HomeLink Button (Canadian/
Gate Operator)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Press and hold the desired HomeLink button until the
indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button, proceed with “Canadian/ Gate Operator Programming” step 2 and follow all
remaining steps.
Using HomeLink
To operate, push and release the programmed HomeLink
button. Activation will now occur for the programmed
device (i.e. garage door opener, gate operator, security
system, entry door lock, home/office lighting, etc.). The
hand-held transmitter of the device may also be used at
any time.
88 GETTING TO KNOW YOUR VEHICLE

Security
It is advised to erase all channels before you sell or turn in
your vehicle.
To do this, push and hold the two outside buttons for 20
seconds until the orange indicator flashes. Note that all
channels will be erased. Individual channels cannot be
erased.
The HomeLink Universal Transceiver is disabled when the
Vehicle Security Alarm is active.
Troubleshooting Tips
If you are having trouble programming HomeLink, here
are some of the most common solutions:
•Replace the battery in the Garage Door Opener hand-
held transmitter.
• Push the LEARN button on the Garage Door Opener to
complete the training for a Rolling Code.
• Did you unplug the device for programming and re-
member to plug it back in?
If you have any problems, or require assistance, please call
toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
WARNING!
• Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run your vehicle in the garage while
programming the transceiver. Exhaust gas can cause
serious injury or death.
• Your motorized door or gate will open and close
while you are programming the universal trans-
ceiver. Do not program the transceiver if people, pets
or other objects are in the path of the door or gate.
Only use this transceiver with a garage door opener
that has a “stop and reverse” feature as required by
Federal safety standards. This includes most garage
door opener models manufactured after 1982. Do not
use a garage door opener without these safety fea-
tures. Call toll-free 1-800-355-3515 or, on the Internet
at HomeLink.com for safety information or assis-
tance.
3
GETTING TO KNOW YOUR VEHICLE 89

Deck LidPower Release ...........................81
Defroster, Windshield ....................... .201
Delay (Intermittent) Wipers ....................65
Diagnostic System, Onboard ...................122
Dimmer Switch Headlight ...............................58
Dipsticks Oil (Engine) ........................... .322
Power Steering ......................... .236
Disable Vehicle Towing ................310, 311, 312
Disposal Antifreeze (Engine Coolant) .................339
Disturb ................................. .455
Door Ajar ................................116
Door Ajar Light ............................116
Door Locks Automatic ..............................40
Door Opener, Garage .........................84
Doors ....................................33
Drag And Drop Menu ...................... .387
Drive Modes ............................. .229
Driver ’s Seat Back Tilt ........................40 Driving
Through Flowing, Rising, Or Shallow Standing
Water ................................ .271
Electrical Power Outlets .......................93
Electric Brake Control System ..................129
Anti-Lock Brake System ....................128
Electronic Roll Mitigation ...............130, 138
Electric Remote Mirrors .......................56
Electronic Power Distribution Center (Fuses) .......284
Electronic Speed Control (Cruise Control) ......238, 240
Electronic Stability Control (ESC) ...............131
Electronic Throttle Control Warning Light .........115
Emergency, In Case Of Freeing Vehicle When Stuck .................309
Jacking ............................... .344
Jump Starting ....................... .303, 304
Towing ........................ .310, 311, 312
Emission Control System Maintenance ............124
Engine .............................. .320, 321
Air Cleaner ............................ .326
Block Heater ............................211
Br

eak-In Recommendations .................212
Checking Oil Level ...................... .322
Compartment .......................... .321
12
INDEX 471

Clean Air............................. .377
Ethanol .............................. .378
Filler Cap (Gas Cap) ..................... .267
Gasoline .............................. .376
Materials Added ........................ .377
Methanol ............................. .378
Octane Rating ....................... .376, 382
Requirements .......................... .376
Specifications .......................... .382
Tank Capacity .......................... .381
Fueling ................................. .267
Fuses .................................. .283
Garage Door Opener (HomeLink) ................84
Gas Cap (Fuel Filler Cap) .....................267
Gasoline, Clean Air ........................ .377
Gasoline, Reformulated ..................... .377
Gear Ranges ............................. .223
Glass Cleaning ........................... .372
Gross Axle Weight Rating .....................269
Gross Vehicle Weight Rating ...................269
GVWR ................................. .269Hazard
Driving Through Flowing, Rising, Or Shallow Standing
Water ................................ .271
Hazard Warning Flashers .....................274
Headlights Automatic ..............................59
Cleaning .............................. .369
High Beam/Low Beam Select Switch ...........58
Lights On Reminder .......................60
On With Wipers ..........................60
Passing ................................59
Switch .................................57
Time Delay ..............................60
Washers .............................. .322
Head Restraints ......................... .48, 49
Head Rests ............................ .48, 49
Heated Mirrors .............................56
Heater ...................................67
Heater, Engine Block ........................211
High

Beam/Low Beam Select (Dimmer) Switch ......58
Hill Start Assist ........................... .135
HomeLink (Garage Door Opener) ................84
Hood Prop ................................80
Hood Release ..............................80
12
INDEX 473