2018 CITROEN DS4 bulb

3
07
08
0609
132 Driving recommendations
13 4
A
nti-theft protection
13 4
S

tarting/Switching off the engine with the
key
136
S

tarting/Switching off the engine with
Keyless Entry and Starting
138
M

anual parking brake
139
E

lectric parking brake
142
M

anual gearbox
14 3
Aut

omatic gearbox
14 6 Gear
ef ficiency indicator
14

7
St
op & Start
14 9
H

ill start assist
15 0
M

emorising speeds
151
Spe

ed limiter
15 3
C

ruise control
15 6
L

ane departure warning system
157
B

lind spot monitoring
15 9
P

arking sensors
161
R

eversing camera
162 Tyre
under-inflation detection 166
Fuel
167
M

isfuel prevention (Diesel)
168
C

ompatibility of fuels
169
S

now chains
170
V

ery cold climate screen
170
T

o w b a r
171
T

owbar with quickly detachable towball
175
L

oad reduction mode
175
E

nergy saving mode
176
C

hanging a wiper blade
176
F

itting roof bars
17 7
B

onnet
178
E

ngines
179
Ch

ecking levels
181


Checks
183


AdBlue
® (BlueHDi engines)
186
A

dvice on care and maintenance
189
T

emporary puncture repair kit
192
S

pare wheel
198
C

hanging a bulb
205
C

hanging a fuse
209
1

2 V battery
212
T

owing the vehicle
214
R

unning out of fuel (Diesel) 216
C

haracteristics of the engines and towed
loads
217
Pe
trol engines
219
D
iesel engines
221

Dimensions
222 Identification
ma
rkings
Driving
Practical information
In the event of a breakdownTechnical data
Alphabetical index DS Connect Nav
Bluetooth
® audio system
Audio and telematics
Contents

90
Storage boxStowing rings
There are four stowing rings in the boot for
securing luggage:
-

t
wo are located on the boot floor,
-

t
wo are located at the lower part of the
entrance.
Boot lighting
This comes on automatically when the boot is
opened and goes off automatically when the
boot is closed.
The lighting time varies according to the
circumstances:
-

w
hen the ignition is off, approximately
ten minutes,
-

i
n energy economy mode,
approximately thirty seconds,
-
w

ith the engine running, unlimited.
F
R
aise the boot carpet for access to the
storage box.
The latter has compartments for storage of a
box of spare bulbs, a first aid kit, etc.
It also contains vehicle tools, the temporary
puncture repair kit, etc.
03
Ease of use and comfort

96
Switching on
F Press the open padlock on the remote control or one of
the front door handles with the
"Keyless Entry and Starting"
system.
The sidelamps and dipped beam headlamps,
as well as the side spotlamps, located under
the door mirrors, come on; your vehicle is also
unlocked.
Switching off
The welcome lighting switches off automatically
after a programmed time, when the ignition is
switched on or on locking the vehicle.
Programming
Activation or deactivation, as well
as the duration of the welcome
lighting can be set via the vehicle
configuration menu.
Headlamp adjustment
Manual adjustment of the
halogen headlamps
To avoid causing a nuisance to other road
users, the height of the halogen headlamp
beams should be adjusted according to the
load in the vehicle.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
-. Intermediate setting.
2. 5 people + maximum authorised load.
-. Intermediate setting.
3. Driver + maximum authorised load.
Automatic adjustment
of xenon and full-LED
headlamps
The initial setting is position " 0".
This system adjusts the height of the xenon
headlamp beams automatically and when
stationary, according to the vehicle's load, so as
to avoid causing a nuisance to other road users.
If a malfunction occurs, this warning
lamp is displayed in the instrument
panel, accompanied by an audible
signal and a message in the screen.
The system then places your headlamps in the
lowest position. In the event of a fault, do not touch the
xenon bulbs.
Have them checked in the dealer network
or by a qualified workshop.
04
Lighting and visibility

103
General safety
recommendations
Labels are attached in different places on
your vehicle. They include safety warnings
as well as identification information for
your vehicle. Do not remove them: they
are an integral part of your vehicle.We draw your attention to the following
points:
-

T
he fitting of electrical equipment
or accessories not approved by DS
AUTOMOBILES may cause excessive
current consumption and faults and
failures with the electrical system
of your vehicle. Contact the dealer
network for information on the range of
recommended accessories.
-

A
s a safety measure, access to
the diagnostic socket, used for the
vehicle's electronic systems, is
reser ved strictly for the dealer network
or qualified workshops, equipped
with the special tools required (risk
of malfunctions of the vehicle's
electronic systems that could cause
breakdowns or serious accidents).
The manufacturer cannot be held
responsible if this advice is not
followed.
-
A

ny modification or adaptation
not intended or authorised by DS
AUTOMOBILES or carried out without
meeting the technical requirements
defined by the manufacturer will result
in the suspension of the legal and
contractual warranties. Installation of accessory radio
communication transmitters
Before installing a radio communication
transmitter with an external antenna,
you must contact a member of the
dealer network for the specification
of transmitters which can be fitted
(frequency, maximum power,
antenna position, specific installation
requirements), in line with the Vehicle
Electromagnetic Compatibility Directive
(2004/104/EC).
Depending on country regulations, some
safety equipment may be compulsory:
high visibility safety vests, warning
triangles, breathalysers, spare bulbs,
spare fuses, fire extinguisher, first aid kit,
mud flaps at the rear of the vehicle, etc.
05
Safety

198
Changing a bulb
The headlamps have polycarbonate
lenses with a protective coating:
F
d
o not clean them using a dr y or
abrasive cloth, nor with a detergent
or solvent product,
F

u
se a sponge and soapy water or a pH
neutral product,
F

w
hen using a high pressure washer
on persistent marks, do not keep the
lance directed towards the lamps or
their edges for too long, so as not to
damage their protective coating and
seals.
Changing a bulb must only be done with
the ignition off and after the headlamp has
been switched off for several minutes –
Risk of serious burns!
F

D
o not touch the bulb directly with your
fingers, use a lint-free cloth.
It is essential only to use anti-ultraviolet
(UV) type bulbs, so as not to damage the
headlamp.
Always replace a failed bulb with a new
bulb with the same type and specification. In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps is
normal; it disappears after the lamps have
been on for a few minutes.
Light-emitting diodes (LED)
For the replacement of this type of lamp,
contact the dealer network or a qualified
workshop.
A LED (light-emitting diode) replacement
kit is available from the dealer network.
For bulbs with lugs, type H1, H7... take
care to position them correctly to ensure
the best lighting.
Risk of electrocution
Xenon bulbs (D1S) must be replaced
in the dealer network or by a qualified
workshop.
Front lamps
With xenon and full LED directional
lamps
1.
Daytime running lamps/sidelamps (LED).
2. Directional main beam/dipped beam
headlamps (D1S).
3. Direction indicators (LED).
4. Directional front foglamps (LED).
08
In the event of a breakdown

199
With halogen headlamps (type 1)
1.Direction indicators (H21 clear).
2. Dipped beam headlamps (H7).
3. Main beam headlamps (H1).
4. Daytime running lamps/sidelamps
(P 21/5 W X L).
5. Foglamps (H11).
With halogen lamps and LED light
signature (type 2)
(LED: light-emitting diodes.)
1. Direction indicators (LED).
2. Daytime running lamps/sidelamps
(LEDs).
3. Dipped beam headlamps (H7).
4. Main beam headlamps (H7).
5. Foglamps (H11).
Access to bulbs
Depending on the engine and only on the left-
hand side, you must first carry out the following
operations for access to the protective covers
on the bulbs.
F

R
emove the air deflector by unclipping each
of its three attachment points.
F

U
nclip the bonnet release cable at its two
fixings.
F

M
ove the cable down.
After changing the failed bulb, remember to
put everything back in place (cable and air
deflector).
08
In the event of a breakdown

200
Direction indicators
Quicker flashing of the direction indicator
lamp (left or right) indicates that one of
the bulbs on the corresponding side has
failed.
Model with halogen headlamps (type 1)
F

T
urn the bulb holder a quarter turn and pull
it out.
F

P
ull out the bulb and replace it.
To reassemble, proceed in reverse order. Model with halogen headlamps (type 2) and
model with xenon headlamps
For the replacement of this type of LED lamp,
contact the dealer network or a qualified
workshop.
Amber colour bulbs, such as the direction
indicators, must be replaced by bulbs with
identical colour and specifications.
To refit, close the protective cover very
carefully to guarantee the leak-tightness
of the lamp. F

D
isconnect the connector.
F

S
pread the springs to release the bulb.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
Dipped beam headlamp bulbs (with
halogen headlamps)
F Remove the protective cover by pulling the tab.
08
In the event of a breakdown

201
Main beam headlamp bulbs (with
halogen headlamps type 1)
F Remove the protective cover by pulling the tab.
F

D
isconnect the connector.
F

S
queeze the springs to release the bulb.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
Main beam headlamp bulbs (with
halogen headlamps type 2)
F Remove the protective cover by pulling the tab.
F

D
isconnect the connector.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
Daytime running lamp/sidelamp bulbs
(with halogen headlamps type 1)
Daytime running lamp/sidelamp bulbs
(with halogen headlamps type 2)
For the replacement of this type of LED lamp,
contact the dealer network or a qualified
workshop. F
R
emove the protective cover by pulling the
tab.
F
D
isconnect the connector.
F
T
urn the bulb holder a quarter turn and
remove it.
F
P
ull out the bulb and replace it.
To reassemble, proceed in reverse order.
08
In the event of a breakdown