2018 CITROEN DS3 bulb

3
07
08
0609
bit.ly/helpPSA
116 Driving recommendations
118
S
tarting-switching off the engine
120
P

arking brake
120
6

-speed manual gearbox
120
E

lectronic gearbox (ETG)
124
Aut

omatic gearbox
127
A

utomatic gearbox (EAT6)
130 Gear
ef ficiency indicator
131
H

ill start assist
132
St

op & Start
13 4 Tyre
under-inflation detection
136
Spe

ed limiter
138
C

ruise control
14 0
A

ctive City Brake
14 3
P

arking assistance
14 4
R

eversing camera 14 8 Fu
el tank
14 8
M

isfuel prevention (Diesel)
15 0
C

ompatibility of fuels
151
S

now chains
152


To w b a r
152
L

oad reduction mode
15 3
E

nergy economy mode
15 3
C

hanging wiper blades
15 3


Bonnet
15 4


Engines
155
Ch

ecking levels
157
C

hecks
15 9
Ad

Blue
® (BlueHDi engines)
162
A

dvice on care and maintenance
165
R

unning out of fuel (Diesel)
165
T

emporary puncture repair kit
169
S

pare wheel
174
C

hanging a

bulb
181
C

hanging a

fuse
188
1

2

V battery
191


To w i n g 194
C

haracteristics of engines and towed
loads
195
Pe
trol engines
198
D
iesel engines
199

Dimensions
201 Identification
ma
rkings
Driving
Practical information
In the event of a
breakdown Technical data
Alphabetical index Audio and telematics
Access to additional videos
7-inch touch screen tablet
Audio system
Contents

81
To avoid any risk of jamming of the pedals:
- o nly use mats which are suited to the
fixings already present in the vehicle;
these fixings must be used,
-

n
ever place one mat on top of another.
The use of unapproved mats may inter fere
with access to the pedals and hinder the
operation of the cruise control/speed
limiter.
The approved mats have two fixings
located below the seat.
Boot fittings
Rear shelf
To remove the shelf:
F u nhook the two cords,
F

g
ently lift the shelf, then unclip it on each
side.
Rear shelf
The rear shelf is fixed .
Before opening the roof completely,
ensure there is nothing left on the shelf. When the roof is completely open, the
screen is placed on the rear shelf. Do not
place any object on the screen.
Storage box
F To access the storage box, lift the boot
carpet by pulling up the strap.
This has areas for the storage of a
temporary
tyre repair kit, a box of spare bulbs, a first aid
kit, two warning triangles, etc.
03
Ease of use and comfort

92
General safety
recommendations
Labels are attached in different places on
your vehicle. They include safety warnings
as well as identification information for
your vehicle. Do not remove them: they
are an integral part of your vehicle.We draw your attention to the following
points:
-

T
he fitting of electrical equipment
or accessories not approved by
DS AUTOMOBILES may cause
excessive current consumption and
faults and failures with the electrical
system of your vehicle. Contact the
dealer network for information on the
range of recommended accessories.
-

A
s a safety measure, access to
the diagnostic socket, used for the
vehicle's electronic systems, is
reser ved strictly for the dealer network
or qualified workshops, equipped
with the special tools required (risk
of malfunctions of the vehicle's
electronic systems that could cause
breakdowns or serious accidents).
The manufacturer cannot be held
responsible if this advice is not
followed.
-
A

ny modification or adaptation
not intended or authorised by
DS
AUTOMOBILES or carried
out without meeting the technical
requirements defined by the
manufacturer will result in the
suspension of the legal and contractual
warranties. Installation of accessory radio
communication transmitters
Before installing a


radio communication
transmitter with an external antenna,
you must contact a member of the
dealer network for the specification
of transmitters which can be fitted
(frequency, maximum power,
aerial position, specific installation
requirements), in line with the Vehicle
Electromagnetic Compatibility
Directive (2004/104/EC).
Depending on country regulations, some
safety equipment may be compulsory:
high visibility safety vests, warning
triangles, breathalysers, spare bulbs,
spare fuses, fire extinguisher, first aid kit,
mud flaps at the rear of the vehicle, etc.
05
Safety

174
Changing a bulb
The headlamps have polycarbonate
lenses with a
protective coating:
F

d
o not clean them using a dr y or
abrasive cloth, nor with a
detergent
or solvent product,
F

u
se a sponge and soapy water or a pH
neutral product,
F

w
hen using a high pressure washer
on persistent marks, do not keep the
lance directed towards the lamps or
their edges for too long, so as not to
damage their protective coating and
seals.
Changing a


bulb must only be done with
the ignition off and after the headlamp has
been switched off for several minutes –
Risk of serious burns!
F

D
o not touch the bulb directly with your
fingers, use a
lint-free cloth.
It is essential only to use anti-ultraviolet
(UV) type bulbs, so as not to damage the
headlamp.
Always replace a
failed bulb with a new
bulb with the same type and specification.
Front lamps
Halogen headlamps
1. Direction indicators (PY21W amber).
2. Sidelamps (W5W).
3. Main beam headlamps (H1-55W).
4. Dipped beam headlamps (H7-55W).
5. LED foglamps.
6. LED daytime running lamps.
Direction indicators
Rapid flashing of the direction indicator
lamp (left or right) indicates that one of
the bulbs on the corresponding side has
failed.
F

T
urn the bulb holder a quarter turn and
remove it.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
Amber colour bulbs, such as the direction
indicators, must be replaced by bulbs with
identical colour and specifications.
To refit, close the protective cover very
carefully to guarantee the leak-tightness
of the lamp.
08
In the event of a breakdown

175
Dipped beam headlamps
Main beam headlampsF Remove the protective cover by pulling the tab.
F

D
isconnect the bulb connector.
F

S
pread the springs to release the bulb.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
Sidelamps
F Remove the protective cover by pulling the tab.
F

D
isconnect the bulb connector.
F

S
pread the springs to release the bulb.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
F

R
emove the protective cover by pulling the
tab.
F

P
ull the bulb holder by pressing the tabs on
both sides.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
LED/Xenon headlamps
(LED: light-emitting diodes.)
1. Direction indicators (LED).
2. Sidelamps (LED).
3. Dipped beam headlights (Xenon).
4. Main beam headlamps (LED/Xenon).
5. LED daytime running lamps.
6. LED foglamps.
For the replacement of this type of lamp
(LED/Xenon), contact the dealer network or
a


qualified workshop.
08
In the event of a breakdown

176
Integrated direction indicator side
repeaters
Contact the dealer network or a qualified
w orkshop to obtain the module.
LED foglamps
LED daytime running lampsRear lamps
Model with conventional bulb lamps
1. Brake/sidelamps (P21/5W).
2. Sidelamps (P5W).
3. Direction indicators (PY21W amber).
4. Foglamp (PR21W red) or reversing lamp
(P21W ).
Model with rear 3D lamps
F Insert a screwdriver towards the centre of
the repeater between the repeater and the
base of the mirror.
F

L
ever with the screwdriver to extract the
repeater and pull it out.
F

D
isconnect the connector from the repeater.
F

R
eplace the module.
To refit, carry out these operations in reverse
o r d e r. For the replacement of this type of diode
lamp, contact the dealer network or a
qualified
workshop.
For the replacement of this type of diode
lamp, contact the dealer network or a
qualified
workshop. 1.
3D LED sidelamps.
2. LED brake/sidelamps.
08
In the event of a breakdown

177
3.LED side marker lamps.
4. Direction indicators (PY21W amber).
5. Foglamp (H21W red) or reversing lamp
(H21W ).
Amber or red colour bulbs, such as the
direction indicators or foglamps, must be
replaced by bulbs with identical colour and
specifications.
Access to bulbs
Removing the access cover
F Open the boot.
Ty p e 1 Ty p e 2Removing the lamp
To reassemble, proceed in reverse order.
Make sure to engage the lamp unit in its guides
while keeping it in line with the vehicle.
Refitting the access cover
Ty p e 1
F

R

emove the access cover by pulling it
downwards.
F

U

nscrew the lamp fixing wing nut.
F

U

nclip the lamp unit connector.
F

E

xtract the lamp unit carefully pulling it
straight towards the outside. F

P
osition the 3 hooks A of the cover in the
lower part.
08
In the event of a breakdown

178
Ty p e 2
Changing bulbs
Model with conventional bulb lampsModel with rear 3D lamps
Direction indicators (4) and foglamp or
reversing lamp (5)
Replacing LED sidelamps and brake
lamps (diodes)
For the replacement of this type of diode
lamp, contact the dealer network or a
qualified
workshop.
F

T

ip the cover upwards and position the
hooks B under the boot trim.
F

Ra

ise the cover.
F

S

lide the cover so as to put it properly back
in place. F

P

osition the cover in the lower part.
F

T

ip the cover upwards.
F
T
urn the bulb a quarter of a turn and change
it.
F

S

pread the four tabs and remove the bulb
h o l d e r.
F

T

urn the bulb a

quarter turn and change it.
08
In the event of a breakdown