2018 CITROEN C-ELYSÉE Control

16
Warning / indicator lampStateCause Action / Observations
SCR emissions
control system
(BlueHDi Diesel) Fixed, on switching on
the ignition, associated
with the Ser vice and
engine auto diagnosis
warning lamps,
accompanied by an
audible signal and a
message. A fault with the SCR emissions
control system has been detected.
This alert disappears once the exhaust emissions
return to normal levels.
Flashing, on switching
on the ignition,
associated with the
Service and engine
auto diagnosis warning
lamps, accompanied by
an audible signal and
a message indicating
the remaining driving
range.After confirmation of the fault with
the emissions control system,
you can continue driving for up to
650
miles (1,100 km) before the
engine starting inhibition system is
triggered. Contact a CITROËN dealer or a qualified workshop
without delay
, to avoid a breakdown .
Flashing, on switching
on the ignition,
associated with the
Service and engine
auto diagnosis warning
lamps, accompanied
by an audible signal
and a message. You have exceeded the authorised
driving limit following confirmation
of a fault with the emissions control
system: the engine starting inhibition
system prevents starting of the
engine.
To be able to restart the engine, you must
call on a
CITROËN dealer or a qualified workshop.
Instruments

17
ServiceTemporarily on. A minor fault has occurred for which
there is no specific warning lamp. Identify the fault by reading the message shown in
the screen, such as, for example:
-

s
aturation of the particle filter (Diesel).
-
t

he power steering,
-

a m
inor electrical fault.
For any other faults, contact a CITROËN dealer or a
qualified workshop.
Fixed. A major fault has occurred for which
there is no specific warning lamp. Identify the fault by reading the message shown in
the screen and then contact a CITROËN dealer or a
qualified workshop.
Rear foglamp Fixed. The rear foglamp has been switched
on using the ring on the lighting
control stalk. Turn the ring on the lighting control stalk rear wards to
switch off the rear foglamp.
Stop & Star t Fixed.
When the vehicle is stopped (red lights,
traffic jams, etc.), the Stop & Start system
puts the engine into STOP mode.The warning lamp goes off and the engine restarts
automatically in START mode, as soon as you want
to move off.
Flashes for a few
seconds, then goes
of f. STOP mode is temporarily
unavailable.
or
START mode has been triggered
automatically. For more information on Stop & Star t
, refer to the
corresponding section.
Warning / indicator lamp
StateCause Action / Observations
1
Instruments

18
Warning / indicator lampStateCause Action / Observations
Front foglamps Fixed. The front foglamps have been
switched on using the ring on the
lighting control stalk. Turn the ring on the lighting control stalk rear ward
once to switch off the front foglamps.
Left-hand
direction
indicator Flashing with audible
signal.
The lighting control stalk has been
moved down.
Right-hand
direction indicatorFlashing with audible
signal.The lighting control stalk has been
moved up.
Dipped beam
headlamps Fixed.
The lighting control stalk is in the
"Dipped beam headlamps" position.
Main beam
headlamps Fixed.
The lighting control stalk has been
pulled towards you. Pull the stalk to return to dipped beam headlamps.
Foot on the
clutch Fixed.
In STOP mode of Stop & Start, the
transition to START mode has been
rejected because the clutch pedal is
not fully pressed down. With a manual gearbox, you must declutch fully to
allow the change to engine START mode.
Foot on the
brake pedal Fixed.
With an automatic gearbox, you have
forgotten to press the brake pedal to
move out of position P.With the engine running, before releasing the parking
brake you must press the brake pedal to unlock the
automatic gear selector lever and move out of the P
position.
Instruments

21
AdBlue® fluid range
indicators
Once the AdBlue® tank is on reser ve or after
detection of a fault with the SCR emissions
control system, when the ignition is switched
on, an indicator displays an estimate of the
distance that can be covered, the range, before
engine starting is prevented.
In the event of a simultaneous system fault and
low AdBlue
® level, the shortest range figure is
the one displayed.
In the event of the risk of
non-starting related to a
lack of AdBlue
®
The engine starting inhibition system
required by regulations is activated
automatically once the AdBlue
® tank is
e m pt y.
Range greater than 1,500

miles (2,400 km)
When switching on the ignition, there is no
automatic display of the range in the instrument
panel.
Resetting the service indicator
After each service, the service indicator must
be reset to zero.
Following this operation, if you wish to
disconnect the battery, lock the vehicle
and wait at least five minutes for the zero
reset to be taken into account.
Retrieving the service
information
You can access the ser vice information at any
time.
F
P
ress the trip distance recorder reset
button. The ser vice information is displayed
for a few seconds, then disappears.
The procedure for resetting to zero is as
follows:
F

S

witch off the ignition.
F

P

ress and hold the trip distance recorder
reset button.
F

S

witch the ignition on; the distance recorder
display starts a countdown.
F

R

elease the button when =0

is displayed;
the spanner disappears.
1
Instruments

23
If it is a temporary fault, the alert
disappears during the next journey,
after auto diagnosis checks of the SCR
emissions control system.
During the permitted driving phase
(between 650
and 0 miles (1,100 km and
0


km))
While driving, the message is displayed every
30

seconds while the fault with the SCR
emissions control system persists.
The alert is repeated when switching on the
ignition. Starting prevented
You have exceeded the authorised driving
limit: the starting inhibition system does
not allow the engine to be started.
To be able to restart the engine, you must call
on a CITROËN dealer or a qualified workshop.In the event of a fault with
the SCR emissions control
system
An engine starting inhibition device is
activated automatically after you have
driven a further 650 miles (1,100 km)
following confirmation of a fault with the
SCR emissions control system. Have the
system checked by a CITROËN dealer or
a qualified workshop as soon as possible.
In the event of the detection of a fault
These warning lamps come on, accompanied
by an audible signal and the display of the
message "Emissions fault".
The alert is triggered while driving as soon
as the fault is detected for the first time, then
when switching on the ignition for subsequent
journeys, while the fault persists. If a fault with the SCR system is confirmed
(after 30
miles (50 km) covered with the
permanent display of the message signalling
a fault), these warning lamps come on and the
AdBlue warning lamp flashes, accompanied
by an audible signal and the temporary display
in the instrument cluster of NO START IN
and a distance, indicating the driving range
expressed in miles or kilometres before engine
starting is prevented – (e.g. "NO START IN
350
miles" means "Starting will be prevented in
350


miles").You should go to a CITROËN dealer or a
qualified workshop as soon as possible.
Other wise you will not be able to restart the
vehicle.
When switching on the ignition, these warning
lamps comes on and the AdBlue warning lamp
flashes, accompanied by an audible signal and
the temporary display of "NO START IN" and
0
miles or kilometres on the instrument panel –
("NO START IN 0
miles" means "Starting
prevented").
1
Instruments

25
Audio system / Bluetooth With CITROËN Connect Radio
F Select the "Settings" menu.
F
Sel
ect "Date and time ".
F

Sel
ect the " Date" or "Time " tab.
F

C
hoose the display formats.
F

C
hange the date and/or time using the
numeric keypad.
F

C
onfirm with " OK".
The system does not automatically
manage the change between winter and
summer time (depending on country).
With CITROËN Connect Nav
Adjustment of the time and date is only
available if synchronisation with GPS is
deactivated.
F

Sel
ect the " Settings " menu.
F

P
ress the " OPTIONS " button to go to the
secondary page.
F

Sel
ect "Setting the time- date". F

Sel
ect the "
Date" or "Time " tab.
F
A
djust the date and/or time using the
numeric keypad.
F
C
onfirm with "
OK".
Additional adjustments
You can choose:
-
T o change the display format of the date
and time (12h/24h).
-

T
o change the time zone.
-

T
o activate or deactivate synchronisation
with the GPS (UTC).
The system does not automatically
manage the change between winter and
summer time (depending on country).
The change between winter and summer
time is done by changing the time zone.
Operate the audio system buttons in the
following order:
F

P

ress the ‘ MENU’ button.
F

U

sing the arrows, select the
" Personalisation- Configuration " menu
and confirm by pressing the control knob.
F

U

sing the arrows, select the " Screen
configuration " menu then confirm.
F

U

sing the arrows, select the " Set date and
time " menu then confirm.
F

S

elect the setting then confirm.
F

M

odify the setting then confirm again to
save the change.
F

A

djust the settings one by one, confirming
each time.
F

Sel

ect the " OK" tab in the screen and
confirm to exit the " Set date and time"
menu.
1
Instruments

26
Trip computer
Information displayed about the current journey
(range, fuel consumption, average speed, etc.).
Instrument Panel Screen
Monochrome screen C
Data displays
F Press the button at the end of the wiper stalk to display successively the different
trip computer data. The trip computer data
is as follows:
-


Range.
-

C
urrent fuel consumption.
-
D

istance travelled.
-
A

verage fuel consumption.
-
A

verage speed.
F

T
he next press then returns you to the
normal display.
Zero reset
F Hold the control down for more than two seconds to reset to zero the distance
travelled, the average fuel consumption and
the average speed.
Touch screen
Information is accessible from the
menu Driving / Vehicle .
Instruments

27
Display of information in the touch screen
Permanent display:
With CITROËN Connect Radio
F
Sel
ect the " Applications " menu, then " Tr i p
computer ".
With CITROËN Connect Nav
F

Sel
ect the " Applications " menu then the
" Vehicle apps " tab then "Trip computer ".
The trip computer information is displayed in
tabs.
F

P
ress one of the buttons to display the
desired tab.
Temporar y display in a specific window:
F

P
ress the end of the wiper control stalk
to access the information and display the
different tabs. The current information tab with:
-
Range.
-

C
urrent fuel consumption.
-

S
top & Start time counter.
The trip " 1" tab with:
-

A
verage speed for the first trip.
-
A

verage fuel consumption.
-
D

istance travelled.
The trip " 2" tab with:
-

A
verage speed for the second trip.
-
A

verage fuel consumption.
-
D

istance travelled.
Trip reset
F When the desired trip is displayed, press the reset button or on the end of the wiper
control stalk.
Tr i p s " 1" and " 2" are independent and are used
identically.
Tr i p " 1" allows daily calculations to be carried
out, for example, and trip " 2" allows monthly
calculations.
1
Instruments