2018 CHEVROLET CAMARO ZL1 wheel alignment

Chevrolet Camaro High Performance Owner Manual Supplemen (GMNA-
Localizing-U.S./Canada/Mexico-11348335) - 2018 - CRC - 4/5/17
20 Driving and Operating
3. Turn the spring perch upwardto increase spring preload,
or downward to decrease
spring preload.
4. Torque the spring seat bolt to 10Y (7.4 lb ft).
5. Verify and adjust the vehicle alignment as needed following
the spring seat adjustment.Adjustable Rear Stabilizer Bar
(ZL1 1LE Only)
The rear stabilizer bar ends have
three attachment positions that
allow the rear roll stiffness of the
vehicle to be adjusted. The stabilizer bar stiffness
increases approximately 15% using
the rearward holes, or decreases
approximately 10% using the
forward holes.
To change the attachment position:
1. Raise and support the rear of the vehicle.
2. Remove the stabilizer bar link nut while holding the ball
stud end.
3. Reposition the stabilizer bar link stud to the desired hole
and tighten to 43 Y(32 lb ft).
Use the same hole position for
both sides of the vehicle.
Wheel Alignment
Track alignment specifications are
for vehicle at curb weight conditions
(full tank of fuel, zero ballast).

Chevrolet Camaro High Performance Owner Manual Supplemen (GMNA-
Localizing-U.S./Canada/Mexico-11348335) - 2018 - CRC - 4/5/17
Driving and Operating 21
Racing and competitive driving wheel alignment settings can be set as follows for increased handling performance:
Track Wheel Alignment Specifications
Model AxleCaster (Not
Adjustable) Camber Total Toe Steering
Wheel Angle Thrust Angle
Left Right Left Right (Left + Right) (Left −Right)/2
ZL1/1LE Track
Alignment Settings Front 7.9° 7.9°
−2.7°
± 0.15° −2.7°
± 0.15° 0.1° ± 0.05° 0.0° ± 3.5°
—
Rear — — −2.0°
± 0.15° −2.0°
± 0.15° 0.1° ± 0.05°
—0.0° ± 0.1°
ZL1 Track Alignment Settings Front 6.9° 6.9°
−2.0°
± 0.15° −2.0°
± 0.15° 0.1° ± 0.05° 0.0° ± 3.5°
—
Rear — — −1.5°
± 0.15° −1.5°
± 0.15° 0.1° ± 0.05°
—0.0° ± 0.1°
SS 1LE Track
Alignment Settings Front 6.9° 6.9°
−2.0°
± 0.15° −2.0°
± 0.15° 0.1° ± 0.05° 0.0° ± 3.5°
—
Rear — — −1.5°
± 0.15° −1.5°
± 0.15° 0.1° ± 0.05°
—0.0° ± 0.1°
LS/LT 1LE Track
Alignment Settings Front 7.2° 7.2°
−2.0°
± 0.15° −2.0°
± 0.15° 0.1° ± 0.05° 0.0° ± 3.5°
—
Rear — — –1.25°
± 0.15°–1.25°
± 0.15° 0.1° ± 0.05°
—0.0° ± 0.1°

Chevrolet Camaro High Performance Owner Manual Supplemen (GMNA-
Localizing-U.S./Canada/Mexico-11348335) - 2018 - CRC - 4/5/17
22 Driving and Operating
Caution
Using these wheel alignment
settings may cause excessive tire
wear. Only use these wheel
alignment settings for racing or
competitive driving. Excessive tire
wear is not covered under the
vehicle warranty.
Custom Launch Control
(ZL1 Only)
Custom Launch Control allows the
following parameters for Launch
Control to be modified:
.Launch RPM
. Slip Target (5%–15%)
. Surface Type
To adjust the Launch RPM, all of
these conditions must be met:
. The vehicle must be in Track
Mode. See “Track Mode” under
“Driver Mode Control” in the
owner ’s manual. .
Performance Traction
Management (PTM) Mode must
be enabled. For convertibles,
Competitive Driving Mode must
be enabled. See “Driver Mode
Control” in the owner ’s manual.
. The steering wheel must be
straight.
. The driver door must be closed.
. The transmission must be in a
gear other than R (Reverse).
It will work in P (Park) or
N (Neutral).
. The parking brake must not be
engaged.
For more information on
Competitive Driving Mode, see
Competitive Driving Mode 028.
1. Using the buttons on the right
side of the steering wheel,
press
oto open the top level
DIC menu. Use
xto scroll
down to Options and
press SEL.
2. Useworxto navigate to the
Launch Control menu.
Select the Surface using the
MODE switch on the center
console.