Check ing and F illing
"' Position the bottle on the filler tube and turn
the bottle clockwise unti l it stops turning.
"' Press lightly aga inst the bottom of the bott le
to empty it. Continue pressing the bottom of
the bottle until it is empty or unti l fluid stops
flowing into the tank .
"' Remove the bottle and seal the filler neck
¢ page 322, Completing AdBlue refill .
0 Note
Only use refill bottles that are approved for
your vehicle. Us ing other systems can ca use
Ad Blue to leak.
-You can obta in refill bottles from an author
i zed Audi dealer or authorized A udi Service
F ac ility.
- A pe rm itted refill bottle conta ins approxi
mately 0 .5 gallon ( 1.9 liters) of Ad Blue.
Completing AdBlue refill
Applies to: vehicles with selective catalytic reduction
Closing the filler neck
"'Turn the Ad Blue cap to the r ight on the filler
tube unti l th e cap cl ic k s into
p lace ¢.&. in
Prepara tion on page 320,
¢ (Din Preparation
on page 320 ..
"' Then press on the left side of the tank door un-
ti l it latches.
After filling
The vehicle must be driven so tha t the system
recognizes t hat the Ad B lue was refilled. This can
t ake severa l m in utes.
"' If there was no Ad Blue left in the tank and a
r ange of O mi (0 km) was shown in the d isplay,
swi tch the ign ition on fo r abo ut 30 seconds be
f ore star ting the engine .
(D Tips
Ad Blue in the tank can free ze at very low tem
pera tures. If this happens, the system will
not detect that the AdB lue was refilled and it
w ill contin ue to inform you of the low AdBlue
322
leve l. The message tu rns off as soon as the
tank thaws out again .
Emissions control
systems
Cat alytic converter
Applies to: vehicles with gasoline engines
T he vehicle may only be driven w ith un leaded
gaso line, otherwise the catalytic converter will be
destroyed .
Never drive unti l the tan k is comp lete ly empty .
T he irregu lar supply of fuel that resu lts from that
can cause eng ine misfires. Uncombusted fuel will
enter the exhaust system , which can cause over
heating and damage to the catalytic converte r.
Di esel particulate filt er
Applies to: vehicles with diesel engines
The diese l particulate filter filters nearly all of
the soot part icles out of the exhaust. The filter
cleans itself automat ica lly under norma l dr iv ing
cond it io ns. If the filter cannot clean itself (for ex
amp le, because yo u are on ly driving short distan
ces), the filter becomes clogged with soot and
the
1111 i ndicato r light for the diese l particulate
filte r tu rns
on ¢ page 33.
_&. WARNING
The tempera ture o f the e xhaust sys tem is
h igh, both when driving and a fter stopping
the engine.
-
-Never tou ch the e xhaus t tail p ipes o nce they
have become hot. This cou ld resu lt in burns.
-D o not p ark your vehicle over flamm able
materials such as grass or leaves because
the hig h temperature of the emissions con
trol system (catalyt ic converter or d iese l
pa rticu late filter) co uld start a fire.
- Do not apply underbody protectant in the
exhaust system area, beca use this increases
the risk of f ire.
a co .... N ,....
N .... 0 0
3 co
(D Note
Driving with an insufficient oil level is likely to
cause severe damage to the engine.
@ Tips
-The oil pressure warning display. is not
an indicator of the oil level. Do not rely on
it. Instead, check the oil level in your en
gine at regular intervals, preferably each
time you refuel, and always before going
on a long trip.
-If you have the impression your engine con
sumes excessive amounts of oil, we recom
mend that you consult an authorized Audi
dealer to have the cause of your concern
properly diagnosed. Keep in mind that the
accurate measurement of oil consumption
requires great care and may take some
time. An authorized Audi dealer has instruc
tions about how to measure oil consump
tion accurately.
Checking the engine oil level and adding
engine oil
The engine oil level can be checked in the Info
tainment system
Fig. 269 Engine compa rtment: eng ine oil filler opening
cove r
Checking the engine oil level
- Park the vehicle on a level surface.
- Shut the engine off when it is warm.
0 N
-N
" 00 IX)
-Switch only the ignition back on. Wait approxi-
mately two minutes so that the engine oil can
flow back into the oil pan .
Checking and Filling
- Select in the Infotainment system: the !MENUI
button > Vehicle > left control button > Service
& checks > Oil level.
-Check the oil level in the Infotainment system
display. Add engine oil if the bar in the oil level
indicator is just before "min".
Adding engine oil Follow the safety precautions
~&. in Working in
the engine compartment on page 323.
- Stop the engine and open the hood
~page 324 .
-Unscrew the cap~ on the engine oil filling
opening
~ fig. 269, Qpage 325.
- Carefully add O .S quart (O .S liter) of the correct
oil
~ page 325.
- Close the engine oil filler opening cap.
- Close the hood, restart the ignition after two
minutes and read the current oil level in the In
fotainment system.
A WARNING ...__ --When adding oil, do not let oil drip onto hot
engine components. This increases the risk
of afire.
-You must secure the cap on the oil filler
opening correctly so that oil does not leak
out onto the hot engine and exhaust system
when the engine is running, because this is
a fire hazard.
-Always clean skin thoroughly if it comes into
contact with engine oil.
0 Note
- The engine oil level must not be under the
"min" marking, because this increases the
risk of engine damage.
- If the message II Please reduce oil level
appears, there is too much oil in the engine
and there is a risk of damaging the catalytic
converter and engine. Do not start the en
gine. Contact an authorized Audi dealer or
authorized Audi Service Facility to have ex
cess engine oil extracted if necessary.
- Do not mix any additional lubricants into
the engine oil. Damage caused by such addi-
tives is not covered by the warranty.
IJJ>
327
Wheels
the vehicle placard or tire inflation pressure la
bel, you should determine the proper tire
inflation pressure for those tires).
As an added safety feature, your vehicle has been
equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure tell
tale when one or more of your tires is significant
ly under-inflated. Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure . Driving on a signifi
cantly under-inflated tire causes the tire to over
heat and can lead to tire failure. Under-inflation
also reduces fuel efficiency and tire tread life,
and may affect the vehicle's handling and stop
ping ability.
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re
sponsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres
sure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys
tem is not operating properly. The TPMS mal
function indicator is combined with the low tire
pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi
mately one minute and then remain continuously
illuminated . This sequence will continue upon
subsequent vehicle start-ups as long as the mal
function exists .
When the malfunction indicator is illuminated,
the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly .
352
· If the tire pressure monitoring indicator
appears
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Using the ABS sensors, the tire pressure monitor
ing system compares the tire tread circumfer
ence and vibration characteristics of the individu
al tires. If the pressure changes in one or more
tires, this is indicated in the instrument cluster
display with an indicator light
[I] and a message.
If only one tire is affected, the location of that
tire will be indicated.
The tire pressures must be stored in the Infotain
ment system again each time the pressures
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle
c:> page 353. The tire pressure moni
toring system only monitors the tire pressure you
have stored . Refer to the tire pressure label for
the recommended tire pressure for your vehicle
c:> page 344, fig . 2 77.
Tire tread circumference and vibration character
istics can change and cause a tire pressure warn
ing if:
- the tire pressure in one or more tires is too low
- the tires have structural damage
- the tire was replaced or the tire pressure was
changed and it was not stored
c:> page 353
- tires that are only partially used are replaced
with new tires
Indicator lights
[I]-Loss of pressure in at least one tire c:> ,&..
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys
tem
c:> page 353.
mm (Tire Pressure Monitoring System) Tire
pressure: malfunction! See owner's manual.
If
mm appears after switching the ignition on or
while driving and the
[I] indicator light in the in
strument cluster blinks for approximately one minute and then stays on, there is system mal-
function. Try to store the correct tire pressures
IJJ,,,
Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi
cle's value.
It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The required cleaning and care products can be
obtained from an authorized Audi dealer or au
thorized Service Facility. Read and follow the in
structions for use on the packaging .
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health .
- Always store cleaning and care products out
of reach of children to reduce the risk of poi
soning .
@ For the sake of the environment
- Preferably purchase environmentally-friend
ly cleaning products.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer that deposits such as insects, bird
droppings, tree sap or road salt remain on the ve hicle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
increase the damaging effect .
Before washing, rinse off heavy deposits with
plenty of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a microfiber cloth.
Also, wash the underside of your vehicle once road salt stops being used for the season .
Pressure washers
When washing your veh icle w ith a pressure wash
er, always follow the operating instructions pro
vided with the pressure washer. This is especially
important in regard to the pressure and spraying
distance. Do not aim the spray directly at the
354
seals on the side windows, doors, lids or the sun
roof* or at tires, rubber hoses, insulating materi
al, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozzles or high pressure nozzles.
The water temperature must not be above 140 °F
(60 °().
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows and roof* are closed
and the windshield wipers are off . Follow instruc
tions from the car wash operator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes.
Washing by hand
Clean the vehicle starting from the top and work
ing down using a soft sponge or cleaning brush.
Use solvent-free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint .
Apply the product using a microfiber cloth. To
avoid damaging the paint surface, do not use too
much pressure.
Rinse the vehicle thoroughly with water. Then
clean using a neutral shampoo and a soft micro
fiber cloth .
Rinse the vehicle thoroughly again and let it air
dry. Remove any water residue using a chamois .
A WARNING
-
- Only wash the vehicle when the ignition is
off and follow the instructions from the car
@ Tips
The discharged battery must be properly con
nected to the vehicle's electrical system .
When jump starting or charg ing the battery,
never connect the negative ground cable to
the battery negative post because the battery
manager system must be able to detect the
battery's state of charge. Always connect the
negative ground cable to the negative ground
post of the battery manager control unit.
Using the jump start
cable
Both jump start cables must be connected in the
correct order!
Fig. 295 Engine compartment: connec tors for jump start
cables and a charger
Fig. 296 Ju mp starting us ing a battery in another vehicle:
@ -providing current, @-drained
The procedure described below for connecting
jumper cables is intended to prov ide a jump start
for your vehicle .
Vehicle with discharged battery
•Turnoff lights and accessories, move the auto
matic transmission* selecto r lever to N (Neu
tral) or P (Par k), and set the park ing brake.
Emergency situations
Connecting the positive cable (red) to the
positive terminal
• Open the red cover on the positive terminal
c:>fig. 295 .
1. Secure one end of the positive cable (red) to
the jump start pin
c:> fig. 296 (D (pin under
the red cover = "posit ive") on the vehicle that
needs to be started @.
2. Secure the other end of the positive cable
(red) to the positive termina l@ on the
bat
tery provid ing the current @.
Connecting the negative cable (black) to the
negative terminal
3. Secure one end of the negative cable (black)
to the nega tive term inal @ on the battery
that is providing the current @.
4. Secure the other end of the negative cable
(black) to the jump start
pin @ (hex head pin
= "negative") on the vehicle that needs to be
started @.
Starting the engine
• Start the engine on the vehicle providing the
jump start @and let it run at idle.
• Now start the engine on the vehicle with the
drained battery @.
• If the engine does not start, stop the starting
procedure after 10 seconds and then repeat it
after approx imately 30 seconds.
• Remove the cables when the engines are run
ning. Remove them in reverse order from the
way they were installed.
• Close the red cover on the positive terminal.
T he battery is vented to the outside to prevent
gases from enter ing the vehicle interior . Make
sure that the jumper clamps are well connected
with their
metal parts in full contact with the
battery terminals.
_& WARNING
-To avoid serious personal injury and damage to the vehicle, heed all warnings and instruc
tions of the jumper cable manufacturer. If in
doubt, call for road service.
-Jumper cables must be long enough so that
the vehicles do not touch .
..,_
375
Emergency situations
-When connecting jumper cables, make sure
that they cannot get caught in any moving
parts in the engine compartment.
-Do not bend over the batteries -danger of
chemical burns!
-The battery cell locking screws must be
tightened securely.
-Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c> page 323.
(D Note
Improper hook-up of jumper cables can ruin
the generator.
- Always connect POSITIVE(+) to POSITIVE
(+), and NEGATIVE(-) to NEGATIVE(-)
ground post of the battery manager control
unit.
- Check that all screw p lugs on the battery
cells are screwed in firmly. If not, tighten
plugs prior to connect ing clamp on negative
battery terminal.
-Please note that the procedure for connect
i ng a jumper cable as described above ap
plies specifically to the case of your vehicle
being jump started . When you are giving a
ju mp start to another vehicle, do
not con
nect the negative (-) cable to the negative
(-) terminal on the discharged batte ry @
c> fig. 296. Instead, securely connect the
negative( -) cab le to either a solid metal
component that is firm ly bolted to the en
gine block or to the engine block itself. If
the battery that is being charged does not
vent to the outside, escap ing battery gas
could ignite and explode!
Towing with a tow truck
General hints
Your Audi requires special handling for towing.
The following information is to be used by com
mercial tow truck operators who know how to op
erate the ir equipment safely.
-Never tow your Audi, towing will cause dam
age to the engine and transmission.
376
-Never wrap the safety chains or winch cables
around the brake lines .
- To prevent unnecessary damage, your Audi
must be transported with a flat bed truck .
- To load the vehicle on to the flat bed, use the
towing loop found in the vehicle tools and at
tach to the front or rear anchorage
i:>page 376 and i:>page 377 .
A WARNING
A vehicle being towed is not safe for passen
gers. Never allow anyone to ride in a vehicle
being towed, for any reason.
Front towing loop
Only install the front towing loop when it is
needed.
Fig. 297 F ront bumper: installing the towing loop
The threaded opening for the towing loop is lo
cated on the right s ide of the front bumper.
.,. Remove the towing loop from the vehicle too l
ki t
c> page 360 .
.,. Press the cap inward with brief, forceful p res
sure
c> fig. 297 . The cap will loosen from the
bumper .
.,. Insert the towi ng loop all the way into the
threaded opening and tighten it with a wheel
wrench.
.,. After using, place the towing loop back in the
vehicle tool kit .
A WARNING
If the towing loop is not tightened until it
stops when installing, the threads may be
pulled out when towing the vehicle and that
could cause an accident.
-
a co .... N ..... N .... 0 0
3 co
Emergency call f unction
Au di connect emergency ca ll and service . 202
E me rgency flashe rs . . . . . . . . . . . . . . . . . . . . 56
Emergency starting . . . . . . . . . . . . . . . . . . . 374
E m issions cont rol sys tem . . . . . . . . . . . . . . 32 2
E nergy management . . . . . . . . . . . . . . . . . . 151
Eng ine
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Start/Stop system . . . . . . . . . . . . . . . . . . . . 85
Starting/stopping . . . . . . . . . . . . . . . . . . . . 83
Starting w it h jumper cables . . . . . . . . . . . 374
Eng ine compartment . . . . . . . . . . . . . . . . . . 323
Opening and clos ing the hood . . . . . . . . . . 324
Safety precautions . . . . . . . . . . . . . . . . . . . 323
E ng ine oi l . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Adding . ... ... .. .. ..... ... .. .. .... . 327
Changing . . . . . . . . . . . . . . . . . . . . . . . . . . 328
Checking the oil leve l . . . . . . . . . . . . . . . . . 327
Consumption . ............. .. .. .... .
D. t· k lpS IC .. ... ............. ...... ... .
327
327
O il consumption . . . . . . . . . . . . . . . . . . . . . 326
Specification and viscos ity . . . . . . . . . . . . . 325
T empe rature d isp lay . . . . . . . . . . . . . . . . . . 11
Eng ine sound . . . . . . . . . . . . . . . . . . . . . . . . 134
Eng ine Start/Stop mode
refer to Start/Stop system . . . . . . . . . . . . . 87
E nter ing cha racters/numbers (speller) . . . . 162
Enter ing letters (speller) . . . . . . . . . . . . . . . 162
E n terta inment s liding me nu . . . . . . . . . . . . 160
E ntry/ex it lighting . . . . . . . . . . . . . . . . . . . . . 56
Environment Proper disposal of drained engine o il ... .
Unleaded fuel . .. ........... .. .. .... .
E S C
.. .. .. .. ... .. .. ..... ... .. .. .... .
Hill descent assist ... .... ... .. .. .... .
Offroad mode ... .. .. .... ... .. .. .... .
Sport mode 328
315
1 46
148
147
147
E v asive steering suppo rt . . . . . . . . . . . . . . . 12 1
Event Data Recorder (EDR) . . . . . . . . . . . . . 153
Expanded view . . . . . . . . . . . . . . . . . . . . . . . . 1 5
E xterio r ligh ting . . . . . . . . . . . . . . . . . . . . . . . 54
Exterior mirrors . . . . . . . . . . . . . . . . . . . . . . . 58
E xternal voice operat ion.... ... .. .. .... . 173
Index
F
Factory default settings
Multi Media Interface . . . . . . . . . . . . . . . . 249
Fader (sound) . . . . . . . . . . . . . . . . . . . . . . . . 252
Fastening Booster seats . . . . . . . . . . . . . . . . . . . . . . . 305
Convertib le child safety seats . . . . . . . . . . 303
I n fan t seats . . . . . . . . . . . . . . . . . . . . . . . . 301
Fast forwarding/rewind ing (a udio/video
file) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
F ast forwarding ( aud io/v ideo file) . . . . . . . . 236
Fast route
Favorites Media 211
239
Navigation . . . . . . . . . . . . . . . . . . . . . . . . . 206
Telephone. . . . . . . . . . . . . . . . . . . . . . . . . . 180
F ile formats (media drives) . . . . . . . . . . . . . 242
Floor ma ts ..... ... .. ................ .
Foot peda ls . .... .. ................. . . 259
259
F o r the s ake o f th e e nv ironmen t
E nvironmenta lly-friend ly driving . . . . . . . . 80
Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Leaks ... .. .... .. .. ... .. ..... ... .. .. 324
Warming up the engine . . . . . . . . . . . . . . . . 83
F ree text search . .. .. .. .
............ ..
Media .. .. .... .. .. .... . ..... ... .. ..
Navigation .... .. ... .. .. ..... ... .. . .
Radio
. . .. .. ' . .. .. ... .. ..... ... .. . .
Telephone . .... .. ................. . .
F ree ze p ro tect ion 164
2 38
205
223 184
Coo lant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 9
Freq uency band . . . . . . . . . . . . . . . . . . 222, 225
Front airbags Desc ription . . . . . . . . . . . . . . . . . . . . . . . . . 275
How they work . . . . . . . . . . . . . . . . . . . . . . 281
F rontal collisions and the laws o f physics . . 264
Front passenger 's doo r eme rgency locking . . 42
Front seats Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Child restra ints in the front seat . . . . . . . . 272
also refer to Seats . . . . . . . . . . . . . . . . . . . . 65
Fuel Additives
.. .... .. ................. .. 315
B lended gasoline . . . . . . . . . . . . . . . . . . . . 315
Current consumpt io n . . . . . . . . . . . . . . . . . .
17
D iesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
391
Index
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 10
Speed warning system . . . . . . . . . . . . . . . . . 102
Speller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Sport differentia l . . . . . . . . . . . . . . . . . . . . . 134
Indicator light . . . . . . . . . . . . . . . . . . . . . . . 35
Sport view . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Stabilization program
refer to ESC . . . . . . . . . . . . . . . . . . . . 146, 147
Start/Stop system . . . . . . . . . . . . . . . . . . . . . 85
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Switching off/on . . . . . . . . . . . . . . . . . . . . . 87
S T ART ENGINE STOP button . . . . . . . . . . . . . 83
Starting to drive . . . . . . . . . . . . . . . . . . . . . . . 89
Starting (engine) . . . . . . . . . . . . . . . . . . . 83, 86
Steering Electromechanical steering . . . . . . . . . . . . 150
L ocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
also refer to Electromechanical steering 150
Steering wheel Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Shift paddles . . . . . . . . . . . . . . . . . . . . . . . . 94
Steering wheel heating . . . . . . . . . . . . . . . . 79
also refer to Multifunction
steering wheel . . . . . . . . . . . . . . . . . 13, 15, 16
Steps for determining correct load limit . . . 348
Stopover (navigation) . . . . . . . . . . . . . . . . . . 209
Stopping (engine) . . . . . . . . . . . . . . . . . . . . . . 86
Storage compartments . . . . . . . . . . . . . . . . . 69
Stored stations
refer to Favorites . . . . . . . . . . . . . . . . . . . . 225
Streaming
refer to Online media . . . . . . . . . . . . . . . . . 232
Street View . . . . . . . . . . . . . . . . . . . . . . . . . . 216
S tronic (automatic transmission) . . . . . . . . . 91
Subtitles (DVD) . . . . . . . . . . . . . . . . . . . . . . . 239
Subwoofer. . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Sunshade Rear window/rear doors . . . . . . . . . . . . . . . 60
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Suspension control . . . . . . . . . . . . . . . . . . . . 134
Swap call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Switching tabs
refer to Multifunction
steering wheel . . . . . . . . . . . . . . . . . 13, lS, 16
Switching the ignition on/off. . . . . . . . . . . . . 83
398
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16S
Navigation . . . . . . . . . . . . . . . . . . . . . . . . . 214
Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
also refer to Indicator lights . . . . . . . . . . . . 2S
SYNC (button) . . . . . . . . . . . . . . . . . . . . . . . . . 79
System settings (MMI) . . . . . . . . . . . . . . . . . 248
System update (MMI) ... ............... 251
System volume 252
T
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . 10, 12
Tail lights
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
TOI clean diese l
refer to Ad Blue... .. .. ............... 319
Technical data ...... ... ............... 379
Technical modifications . . . . . . . . . . . . . . . . 386
Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Connecting . . . . . . . . . . . . . . . . . . . . . . . . . 175
Dialing a number . . . . . . . . . . . . . . . . . . . . 178
Options during a phone call . . . . . . . . . . . 179
Playing music . . . . . . . . . . . . . . . . . . . . . . . 230
Set tings . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Temperature display Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Outside temperature . . . . . . . . . . . . . . . . . . 10
Tether anchors . . . . . . . . . . . . . . . . . . . . . . . 312
Tether strap .. .. .. .. .. ............. .. 312
Text messages . . . . . . . . . . . . . . . . . . . . . . . 180
Tie-downs . . . . . . . . . . . . . . . . . . . . . . . . 73, 261
Tightening specification Wheel bolts . . . . . . . . . . . . . . . . . . . . . . . . 366
Tightening specification (wheel bolts) . . . . 366
Time ......... ... ... ............. ... 248
Tire Mobility System (tire repair set) . . . . . . 361
Tires....... .. .. .. .. .. ... .......... .. 334
Low-profile tires . . . . . . . . . . . . . . . . . . . . . 350
quattro . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Repair set . . . . . . . . . . . . . . . . . . . . . . . . . . 361
R eplacing . . . . . . . . . . . . . . . . . . . . . . . . . . 363
Tire pressure . . . . . . . . . . . . . . . . . . . . . . . 344
Tire pressure monitoring system ... 351,352
Tire pressure table . . . . . . . . . . . . . . . . . . . 345
Tire pressure (trailer towing mode) . . . . . . 99
Unidirectional . . . . . . . . . . . . . . . . . . . 336, 366
Uniform tire quality grading . . . . . . . . . . . 351