2018 AUDI Q5 low beam

u co ..... N ,..._
N ..... 0 <( 0 00
Certain instrument cluster content can also be
displayed in the head-up display*
¢ page 18.
A WARNING
Do not assume the roads are free of ice based
on the outside temperature display . Be aware
that there may be ice on roads even when the
outside temperature is around 41 °F (+5 °C)
and that ice can increase the risk of accidents .
(D Tips
-Depending on vehicle equipment, the in­
strument illumination (needles and gauges) may turn on when the lights are off and the
ignition is switched on . The illumination for
the gauges reduces automatically and even­
tually turns off as brightness outside in­
creases. This function reminds the driver to
turn the low beams on at the appropriate
time.
- You can select the units used for tempera­
ture, speed and other measurements in the
Infotainment
system ¢ page 245.
-If your vehicle is stationary or if you are driv­
ing at very low speeds, the temperature dis­
played may be slightly higher than the ac­
tual temperature outside due to the heat ra­
diating from the engine.
- At temperatures below 41 °F (+5 °C), a
snowflake symbol appears in front of the
temperature
display ¢,&. .
Coolant temperature indicator
The coolant temperature display @¢ page 10,
fig . 3
or ¢ page 10, fig . 4 only functions when
the ignition is switched on. To prevent engine
damage, please observe the following notes
about the temperature ranges.
Cold range
If only the LEDs at the bottom of the gauge turn
on, the engine has not reached operating tem­ perature yet . Avoid high engine speeds, full ac­
celeration and heavy engine loads.
Cockpit overview
Normal range
The engine has reached its operating tempera­
ture once the LEDs up to the center of the gauge
turn on. If
the. indicator light in the instru­
ment cluster display turns on, the coolant tem­
perature is too
high ¢ page 23.
@ Note
-Auxiliary headlights and other accessories in
front of the cooling-air intake impair the
cooling effect of the coolant. This increases
the risk of the engine overheating during
high outside temperatures and heavy en­
gine load .
- The front spoiler also helps to distribute
cooling air correctly while driving. If the
spoiler is damaged, the cooling effect will
be impaired and the risk of the engine over­
heating will increase. See an authorized
Audi dealer or authorized Audi Service Fa­
cility for assistance.
Tachometer
The tachometer displays the engine speed in rev­
olutions per minute (RPM).
The beginning of the red zone in the tachometer
indicates the maximum permissible engine speed
for all gears once the engine has been broken in
and when it is warmed up to operating tempera­
ture. Before reaching this zone, you should shift
into the next highest gear, select the "D/S" selec­
tor lever position, or remove your foot from the
acce lerato r pedal.
@ Note
The needle in the tachometer @¢ page 10,
fig. 3
or ¢ page 10, fig. 4 may only be in the
red area of the gauge for a short time or there
is a risk of engine damage . The location where
the red zone begins varies depending on the
engine.
@) For the sake of the environment
Upshifting early helps you to save fuel and re­
duces operating noise.
11

Cockpit overv ie w
Canada mod els:
speed war ning system*
¢ poge95
Active lane ass ist*
¢ page 118
Aud i side assist*
¢page 125
Camera-based traffic sign recogni­
tion*
¢poge98
H igh beam assistant *
¢poge46
High beams
¢ poge46
High beam assistant *
¢poge46
BRAKE/(©) Brake system
If th is ind icator light turns on, there is a malfunc­
tion in the brake system .
1111 (USA mod els ) /. (Canada models )
Brakes: stop veh icle and chec k bra ke fluid le vel
Stop the vehicle and check the brake fluid level.
See an authorized Audi dea ler or authorized Audi
Serv ice Facility for assistance if necessary.
1111 ( USA model s) /. (Canada model s)
B rake s: malfunction! Stop vehicle safel y
If t he i nd icator lig ht tu rns on and th is message
appears, there is a malfunc tion in the brake
booster.
I f t he ABS indicato r
light ~ (U SA mode ls) /
fee) (Canada mode ls), the ESC indicato r light Bl
a nd the bra ke system ind ic a tor light 1111 (USA
models)
/ . (Canada mode ls) all turn on and
this message appears, then t he ABS, ESC and
braking distribution are malfunctioning
¢ .&. .
Do not cont inue d rivi ng. See an autho rized Aud i
dea le r or autho rized Aud i Serv ice Facili ty fo r as ­
sistance
¢ .& .
1111 (USA m od els)/ . (Canada model s) Park­
ing brake : malfun ction! Saf ely s top v ehicl e. Se e
owner 's manual
22
-If the ind icator light and the message appear
when the vehicle i s station ary or afte r switch­
ing the ignition on ,
check if you can re lease the
parking brake. If you cannot release the park­
ing brake, see an authorized Audi dealer or au­
thorized Audi Service Fac ility . If you can release
the parki ng brake and the message st ill ap­
pears , see an author ized Audi dealer or autho r­
ized Aud i Serv ice Fac ility immediately to have
the ma lfu nction correc ted.
- If the ind icator light and message appear
while
dri ving ,
the hill sta rt ass ist o r emergency brak­
ing function may be ma lfunction ing. It may not
be poss ible to set the park ing b rake o r release
it once it has been set. Do not park yo ur vehicle
on hills . See an aut horized Audi dea ler or au ­
thorized Audi Service Faci lity for assistance .
Brake boo ster : limited functionality . You can
continue d riv ing . Plea se cont act Ser vice
There is a ma lfunction in the b rake booster . The
brake booste r is ava ilab le, but its effective ness is
r educed. Br aking behavior may be d ifferent from
how it normally f unctions and the brake peda l
may vibrate .
D rive to an au thor ized A udi dealer or au tho riz ed
Audi Se rvice Fac il ity immed iate ly to have the
malfunction cor rected.
& WARNING
- Read and fo llow the warnings in
¢ page 314, Working in the engine com ­
portment
before opening the hood and
checking the brake fluid level.
- If the brake system indicator light does not
turn off or it turns on wh ile driving, the
brake flu id leve l in the reservo ir is too low,
and this increases the risk of an accident .
Stop the vehicle and do not continue driv­ ing . See an a utho rized Aud i dea le r o r au­
thor ized A udi Se rvi ce Fac il ity for assistan ce.
- If t he brake system indicator light t urns on
together w it h the ABS and ESC indicator
lights, t he ABS/ ESC regu lating fu nction may
be ma lf u nct io ni ng. Funct io ns tha t stabi lize
the vehicle a re no longer available. This
co uld cause the vehicle to swerve, which
Ill>

Cockpit overv ie w
Drive to an authorized Audi dea le r or a uth orized
Audi Service Facility immediately to have the
malfunct ion corrected .
·:q'): · Bulb failure indicator
If the II indicator light turns on, a bu lb has
fa iled. The message ind icates the location of the
bulb. Replace the bulb immediately .
Vehicle lights: malfunction! Plea se cont act
Service
There is a malfunction in the head lights or the
lig ht switch. Drive to an autho rized A udi dealer or
author ized Audi Service Facility immed iate ly to
have the ma lfunction corrected.
A WARNING
- light bu lbs are under pressure and can ex­
plode when bulbs are replaced, which in­
c reases the risk of injury.
- With HID headlights (xenon headlights), the high-voltage componen t must be handled
correctly. Othe rw ise, there is a risk of fata l
lnJUry.
i,(D Dynamic headlight range control
II Headlight rang e control : malfun ction! See
owner 's manual
There is a malfunc tion in the headl ight range
cont rol system, wh ich may ca use g la re fo r othe r
d rivers.
Drive to an authorized Aud i dea ler or aut horized
Aud i Serv ice Facility immediately to have t he
malfunct io n corrected.
~O Audi adaptive light
App lies to: ve hicles w ith Audi adaptive light
Ill Audi adaptive light : malfunction! See own­
er' s manual
-
Adapt ive light is not work ing . The headlights st ill
f un ction.
Drive to an authorized Aud i dea ler or a uthorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
28
@. D Light/rain sensor
II Automa tic h eadlight s: malfun ction! See
owner' s manual
l;I Automat ic wipers: malfunction ! See owner's
manual
The light/rain sensor is malfunctioning.
The low beams remain switched on at all times
for safety reasons when the light switch is in the
AUTO position. However, yo u can cont inue to
turn the lig hts on and
off using the light switch.
You can sti ll contro l all functions that are inde ­
pendent of t he rain senso r thr ough the wind­
shield wipe r leve r.
D rive to an authorized Audi dealer or authorized
Audi Service Fac ility immed iate ly to have the
malfunction corrected .
g Suspension control
Applies to : vehicles wit h suspension control
R Suspension : malfunction! You may continue
driving
There is a suspension control malfunction.
Drive to an authorized A udi dealer or authorized
Audi Service Facility immed iate ly to have the
malfunction corrected .
~: All wheel drive/sport differential
App lies to: vehicles wit h all w hee l drive/s port diffe re n tial
Ill All-wheel drive : malfunction! You may con­
tinue driv ing. Please contact Service
Ill Sport d ifferential: malfunct ion! Please con­
tact Service
There is a ma lf u nction.
D rive to an au thor ized A udi d ealer or au thori ze d
Audi Se rvice Facility immediate ly to have the
malfunction corrected.
Ill All -wheel driv e overheating . Please adapt
driving style . See owner's manual
Ill Sport differential: temperature too high .
Pl ease adapt driving style

Lights and Vision
Exterior Lighting
Switching the lights on and off
--- ----~-----'~
i
Fig. 37 Instrument p anel: l ig ht switc h with buttons
Light switch ·'!:! ·
Turn the light sw itch to the corresponding posi­
tion when the ignition is switched on.
:oo: and the
selected pos ition turn on (except pos ition 0).
0 -The daytime r unning lights automat ica lly t urn
on. In vehicles for certain markets, you can
switch the automatic daytime running lights on
and off in the Infotainment system*.
AUTO
-T he headlights automatically adapt to the
surrounding brightness.
: oo : -Parking lights
io -Low beam headlights
Buttons
When you turn the light switch to the AUTO or
low beam headlight pos ition
io, you can activate
the following functions:
~ o -A ll-weather lights. The headlights automati ­
cally adjust so that there wi ll be less glare, for
examp le when the road surface is wet.
O t -Rear fog lights
Automatic headlight range control system
Your veh icle is equipped with an automatic head ­
l ight range contro l system that re duces g lare fo r
oncoming traffic i f the vehicle load c hanges. The
~ headlight range ad justs automatica lly . ..... N r-­N .....
~ 0 co
Lights and V ision
Audi adaptive light
Appl ies to: vehicles wit h adaptive light
Adaptive ligh t provides better visibili ty whe n it i s
dark by adapting the lights to the road conditions
based on speed , such as on e xpressways, rura l
roads, at intersections, and in c urves. The adap­
t ive light only functions when the light sw itch is
i n the AUTO position .
A WARNING
--Automatic headlights* are on ly intended to
assist the driver. They do not relieve the
driver of responsibil ity to check the head­
lights and to t urn t hem on manua lly based
on t he curren t ligh t and v is ibility condition s.
For examp le, fog canno t be detec ted by the
light sensors. So always switch on the low
beams under these weather co nditions and
when driv ing in the da rk
io .
- To prevent glare for traffic behind yo ur vehi ­
cle, the rear fog lights should only be turned
on in accordance with traff ic regulat ions.
- Always observe legal regulations when
us­
ing the lighting systems desc ribed .
(D Tips
- The lig ht sensor for the automat ic he ad ­
lights * is in the rearview mir ror mount. Do
not p lace any st ickers in this area on the
windshield.
- A warning tone will sound if you open the door when the exte rior lights a re switched
on .
- Only t he front headlights turn on when t he
daytime running lights are switched on *. In
vehicles in certain markets, the tail lights
w ill also turn on .
- In cool or damp weather, the inside of the
head lights, turn signa ls and tail lights can
fog over due to the temperature diffe rence
between the inside and outside . They will
clear shortly afte r swi tching them on . This
does not aff ect the service life of the light­
mg.
45

u co ..... N r-­N .....
~ 0 co
~ Headlight a ssistant : ma lfun ction! See own­
er 's manual
Drive to an autho rized Audi de aler o r a uthorized
Aud i Service Facility immedia tely to have the
mal funct ion corrected. You can still switch the
high beams on or off manually.
i:a Headlight a ssistant : currently unavailable.
Camera view restricted due to surroundings .
See owner 's manual
The camera view is b locked, fo r example by a
s ticker o r debris.
The senso r is located between the interior rear­
view mir ror and the wi ndshield . Do not p lace any
sti cke rs in t his area on the wi ndshi eld.
,& WARNING
High beam assis tan t is only i ntended to assist
th e drive r. The dr iver is still re sponsib le for
contro lling the headlights and may need to
switch them on and off manually depend ing
on light and visib ility conditions. It may be
necessary to ope rate them manua lly in s itua­
tions such as:
- In adverse weather cond itions such as fog,
heavy ra in, b low ing snow or sp raying water .
- On roads where oncoming traffic may be
partially obsc ured, such as expressways .
- W hen there are road users t hat do not have
s ufficient lighting, s uc h as bicyclers o r
vehicles with dirty ta il lamps.
- In tight cu rves and on steep hills .
- In poo rly lit areas .
- Wi th stro ng ref lec to rs, such as s igns.
- I f the area of t he windsh ield near the se nso r
is f ogg ed ove r, dir ty, i cy or covere d w ith a
sti cker.
Adjusting the exterior lighting
The fun ctio ns are adjust ed in the Infotainment
system.
• Select in the Info tainment sys tem: !ME NUI but­
ton
> Vehicle > left contro l butto n > Vehicle
settings > Exterior lighting .
Lights and Vision
Automatic headlights
Yo u ca n adju st the following se ttings in the Au­
tomatic headlights
men u:
Activation time -you can adjust if the a utomat ic
he adlig hts swi tch on
Early , Medium or Late ac­
cording to the sensi tivity of the ligh t se nsor.
Headlight assistant * -you can switch the high
beam assis tan t* on and off.
Entry/exit lighting
When it is dark, the Entry/exit lighting ill umi­
nates the area a round the vehicle when unlocking
the ve hicle and afte r swi tc h ing off the ignit io n
and opening the dr ive r's door.
The
Entry /exit lighting only works when it is
dark and the ligh t sw itch is in the
AUTO position.
Daytime running lights
USA models :
the daytime r unning lig hts can be
switched on/off . Select
On or Off.
Canada model s:
th is fu ncti on canno t be switche d
off. They act ivate au tomatically eac h time the ig ­
nition is switched on.
Emergency flashers
- --- - -- ----
~
Fig . 39 Ce nter console: emergency flasher butto n
The eme rgen cy fla she rs m akes othe r dr iv e rs
aware of your vehi cle in dangerous situa tions.
• Press the ~ button to sw itch t he emergency
fl as he rs on or off.
You can ind icate a lane change or a turn when the
eme rgency flashers are swi tched on by using the
tu rn s ignal leve r. T he emergen cy flashe rs stop
tempor arily.
""
47

u co ..... N r-­N .....
~ 0 co
Version 1
To adjust the brightness of individual zones, se­
lect
Front brightness* , Door brightness or Foot­
well brightness.
Turn the control knob to th e left
or to th e right. Pr ess the control knob to confirm
the b rightness.
Version 2
Select and confirm one of the displayed profiles
by pressing the control knob.
Individual: you can customize the brightness and
color of individual zones. Press the right control
button. Press the control knob again to confirm
the settings.
Audi drive select: the interior and contour light­
ing color changes depending on the driving mode
selected in drive select*
r::?vpage 125.
(0) Tips
The setting is automatically stored and as­
signed to the remote control key that is being
used.
Instrument illumination
The brightness of the illumination for the instru­
ments, display and head-up display* can be ad­
justed.
--------... ~
i
Fig. 43 Instrument i llumination
.. Press the knob to release it.
.. Turn the knob toward "-" or" +" to reduce or in ­
crease the brightness .
.. Press the knob again to return it to its original
position.
Lights and Vision
(D Tips
Depending on vehicle equipment, the instru­
ment illumination (needles and gauges) may
turn on when the lights are off and the igni­
tion is switched on. The illumination for the
gauges reduces automatically and eventually
turns off as brightness outside increases . This
function reminds the driver to turn the low
beams on at the appropriate time.
Vision
Adjusting exterior mirrors
Fig. 44 D river 's doo r: knob fo r the ext erior mirr ors
Turn the knob to the desired position:
0
-all adjustment functions are deactivated .
q;p -adjusting the left/right exterior mirror.
Move the knob in the desired direction .
® -Heats* the mirror glass depending on the
outside temperature.
8 -Folds the exterior mirrors*. To fold the mir ­
rors out, turn the knob to one of the other posi­
tions. In the Infotainment system, you can select if the mirrors fold in automatically when you lock
the
vehicle¢ page 35 .
Front passenger's exterior mirror tilt
function*
To help you see the curb when backing into a
parking space, the surface of the mirror tilts
slightly. For this to happen, the knob must be in
the position for the front passenger's exterior
mirror.
You can adjust the tilted mirror surface by turn- ing the knob in the desired direction. When you
.,.
49

Lights and Vision
@-Fast wiping
©-Single wipe. If you hold the lever in this posi­
tion longer, the wipers switch from slow wiping
to fast wiping .
®-Clean the windshield . The wipers wipe one
time after several seconds of driving to remove
water droplets . You can switch this function off
by moving the lever to position ® within
10 sec­
onds of the afterwipe. The afterwipe function is
r e activated the next time you switch the ignition
on.
Clean the headlights*. The headlight washer sys­
tem* operates only when the low beam head­
lights are on. If you move the lever into position
@, the headlights will be cleaned at fixed inter­
vals .
@-Wipe the rear window. The number of wipes
depends on the windshield wiper movement.
The rear wiper automatically switches on when
the reverse gear is selected and the front wind­
shield wipers are on and running.
(j) -Clean the rear window. The number of wipes
depends on how long the lever is held in position
(z). This may also clean the rearview camera, de­
pending on the vehicle equipment.
A WARNING
- The rain sensor is only intended to assist the
driver. The driver may still be responsible
for manually switching the wipers on based on visibility conditions.
- The windshield may not be treated with wa­ ter-repelling windshield coating agents . Un­
favorable conditions, such as wetness, dark­
ness or low sun, can result in increased
glare, which increases the risk of an acci­
dent. Wiper blade chatter is also possible.
- Properly functioning windshield wiper
blades are required for a clear view and safe
driving ~ page 53, Replacing wiper
blades .
«1j) Note
-If there is frost, make sure the windshield
wiper blades are not frozen to the wind-
52
shield. Switching on the windshield wipers
when the blades are frozen to the wind­ shield can damage the wiper blades.
- The windshield wiper system must be
switched off (lever in position 0) before us­
ing a car wash. This prevents the wipers
from switching on unintentionally and caus­ ing damage to the windshield wiper system.
(D Tips
- The windshield wipers switch off when the
ignition is switched off. You can activate the
windshield wipers after the ignition is
switched back on by moving the windshield
wiper lever to any position .
- Worn or dirty windshield wiper blades result
in streaking. This can affect the rain sensor
function . Check your windshield wiper
blades regularly.
- The washer fluid nozzles for the windshield
washer system are heated at low tempera­
tures when the ignition is on.
- When stopping temporarily, such as at a
traffic light, the speed of the windshield
wipers automatically reduces by one level.
Cleaning the wiper blades
Clean the wiper blades when you see wiper
streaks. Use a soft cloth and a glass cleaner.
Windshield wiper
.,. Place the windshield wiper arms in the service
position
~ page 53.
.,. Fold the windshield wiper arms away from the
windshield.
Rear window wiper
.,. Fold the wiper arm away from the rear window.
A WARNING
Dirty windshield wiper blades can impair vi­
sion, which increases the risk of an accident.
-

u co ..... N r--­N ..... 0 <( 0 00
(D Tips
-Depending on the driving situation, the en­
gine may already stop when
coasting before
the vehicle has come to a complete stop
ll.
- If you select the "D" selector lever position
after shifting into reverse, the vehicle must be driven faster than 6 mph (10 km/h) in or­
der for the Start/Stop system to be active
again.
Stopping/starting the engine
Applies to: vehicles with Start/Stop system
"'Apply the brakes and keep your foot on the
brake pedal until the vehicle has stopped. The
rl1 indicator light appears in the instrument
cluster once the engine stops automatically .
"'The engine starts again when you take your
foot off the brake pedal. The indicator light
turns off.
(D Tips
-The ignition will turn off if you press the
I START ENGINE STOP I button during a stop
phase .
- You can determine for yourself if the engine
will stop or not by reducing or increasing
the amount of force you use to press the brake pedal. For example, if you only lightly
press on the brake pedal in stop-and-go
traffic or when turning, the engine will not
switch off when the vehicle is stationary. As
soon as you press the brake down harder,
the engine will switch off.
- Press the brake pedal during a Stop phase
to keep the vehicle from rolling.
Starting/stopping the engine automat­
ically
Applies to: vehicles with Start/Stop system
The system checks if certain conditions are met
before and during the "stop" phase, and deter­
mines if and how long the engine is stopped de­
pending on the situation. For example, if power
usage is high, the engine will not be stopped .
ll Market-specific
Driving
Along with other conditions, the following fac­
tors influence the automatic engine start or stop:
- Environmenta l conditions (slopes, inclines, ele-
vation, temperature)
- Battery (charge status, temperature, power us-
age)
- Engine temperature
- Assistance systems
- Driving behavior
If the
rid indicator light appears in the instru­
ment cluster display, the engine will not be stop­
ped.
Switching the ignition off automatically
Applies to: vehicles with Start/Stop system
If you leave the vehicle during a "stop" phase, the
engine can be restarted within approximately 30
seconds if the doors are closed, the driver's safe­
ty belt is fastened and the brake pedal is pressed.
If you leave the vehicle longer than 30 seconds,
the ignition will switch off automatically to pre­
vent the vehicle battery from draining. If this is
the case, the message
Start/stop system: igni­
tion will be switched off in 30s
will appear in the
instrument cluster and, if the low beam head­
lights are switched on, the parking lights will
switch on instead. The parking lights will switch
off after approximately 30 minutes or when you
lock the vehicle.
The ignition also switches off when you lock the
vehicle from the outside during a stop phase.
If the Start/Stop system has not turned off the
engine or if you have switched the Start/Stop sys­
tem off manually, the ignition will not be auto­ matically switched off and the engine will contin­
ue to run.
A WARNING
-To reduce the risk of poisoning, never allow
the engine to run in confined spaces.
-
79