2018 AUDI Q5 lock

Child sa fety
- Never put the forward -facing child restraint
up, against or very near the instrument pan­
el.
- Always move the front passenger seat to
the h ighest position in the up and down ad­
justment range and move it back to the
rearmost position in the seat's fore and aft
adjustment range, as far away from the air­
bag as possib le, before insta lli ng the for­
wa rd-facing child restra int.
- Always make sure that the safety belt upper
anchorage is beh ind the child restra int and
not next to or in front of t he ch ild restraint
so tha t the safety belt w ill be properly pos i­
tioned.
- Make s ure tha t the
PASSENGER AIR BAG
OFF ~; light comes on and stays on a ll the
time whenever the ignition is switched on.
A WARNING
Rearward-facing child restraints:
- A ch ild in a rea rw ar d-facing child safety seat
insta lled on the front passenger seat wi ll be
seriously injured and can be killed if the
front airbag inflates
-even with an Ad ­
vanced Airbag System.
- The inflating airbag wi ll hit the child safety
seat or infant carrier with great force and
will smash the chi ld safety seat and child
against the backrest , center armrest, door
or roof.
- Always be especially careful if you must in­
sta ll a rearward facing child safety seat on
the front passenger seat in exceptional c ir­
c u mstances.
- Make sure that the
PAS SENGER AIR BAG
OFF ~; light comes on and stays on all the
t ime whenever the ignition is switched on.
- If the PASSENGER AIR BAG OFF ~; light
does not come o n and stay o n, immed iate ly
install the rea r-fa cing child safety seat in a
re ar seat ing pos ition and have the airbag
system inspe cte d by your Aud i de aler.
304
Activating the convertible locking retractor
Use the convertible locking retractor to secure a
child restraint.
Always heed the child safety seat manufacturer's
i nstruct ions when installing a child restra int in
your vehicle. To activate the convertible locking r etractor:
.,. Place the child restraint on a seat, preferably
on the rear seat .
.,. Slowly pull the belt all th e w ay out .
.,. Route it around or through the child restra int
be lt
path~ .,&..
.,. Push the ch ild safety sea t down with yo ur full
weigh t to ge t the safety belt rea lly tigh t.
.,. Insert t he be lt tong ue into the b uck le for that
seating position .
.,. Guide the safety be lt back into the retractor un ­
til the belt lies flat and snug on the ch ild safety
seat.
.,. You shou ld hear a "cl icking" noise as the belt
w inds back into the inertia reel. Test the con ­
vert ib le lock ing retractor by pull ing on the belt.
You s hou ld no lo nge r be able to pull the belt
out of the retracto r. T he convertib le lock ing re ­
tracto r is now activa ted .
.,. Make sure that the red release button is facing
away from the chi ld restraint so that it can be
unb uc kled quickly .
.,. Pull on the belt to make sure the safety belt is
properly t ight and fastened so that the seat
cannot move forward or s ideways more than
one inch (2 .5 cm) .
A WARNING
Using the wrong ch ild rest raint or an improp­
e rly insta lled child restra int can ca use se rio us
pe rsonal injury or death in a crash.
- Always make sure that the safety be lt re ­
tr actor is locked whe n in stalling a c hild
safety seat . An un lo cked sa fety be lt retr ac­
tor cannot hold the chi ld safety seat in p lace
during normal driving or in a crash.
- Always buckle t he chi ld safety seat fi rm ly in
p lace even if a chi ld is not sitting in it. A
loose chi ld safety seat can fly a round during
a sudden stop or in a crash.

u co ..... N ,..._
N ..... 0 <( 0 00
-Always make sure the seat backrest to w hich
t h e ch ild restraint is installed is in an up­
rig ht position and securely latched into
place a nd ca nnot f old forward. Otherwise,
t h e sea tback with the ch ild safe ty s eat at­
tach ed to it could fly forward in the event of
an acc ident or o ther emergency situation.
- Always read and heed all WARNINGS when­
ever using a child restrained in a veh icle is
being
used¢ page 291. Spec ia l pre caut ions
apply when ins talling a child s afety seat on
the front passenger
seat¢ page 2 70, Child
restraints on the front seat -some impor­
tant things to know.
Deactivating the convertible locking
retractor
The convertible locking retractor for child re ­
straints will be deactivated automatically when
the belt is wound all the way back into the re­
tractor .
~ Press the red button on the safety be lt b uck le.
The belt tongue w ill pop out of the buckle.
~ Gu ide the safety be lt all the way back into its
stowed pos ition .
Always let the safety belt retract complete ly into
its stowed position. The safety belt can now be
used as an ordinary safety belt without the con­
vert ible lock ing retractor for child restra ints .
If the convert ible lock ing retractor should be ac­
tivated inadve rtently, the safety belt must be un­
fastened and guided completely back into its
stowed position to deact ivate this feature .
If the
convert ib le lock ing re tractor is not deact ivated,
the safety belt w ill gradually become tighte r and
u ncomfo rtable to we ar.
_& WARNING
-
Improperly ins talled chi ld safety seats in­
crease the risk of serio us personal injury and
death in a collision.
- Never unfasten the sa fe ty belt to deactivate
the conve rt ible locking retractor for child re­
straints while the ve hicle is moving . You
Ch ild saf ety
wou ld not be rest rained and could be seri­
ously injured in an accident.
- Always read and heed all WARNINGS when­
ever using a child restrained in a vehicle is
be ing
used¢ page 291. Special p recautions
apply when install ing a child safety seat on
the front passenge r seat
¢ page 2 70, Child
restraints on the front seat -some impor­
tant things to know.
LATCH system (lower
anchorages and tethers
for children)
Child Restraint System anchors and how
are they related to child safety
T o p rovide a simp ler and more practicab le way to
attach the ch ild rest raint on the vehicle seat,
Federal regulations require spec ia l lower ancho­
rages in vehicles and devices o n new c hild re­
straints to attach to the vehicle anc horages .
In the United States, the combination of the
tethe r anchorages and the lower anchorages is
now generally called t he LATCH system for
" Lower Anchorages and Tethers for Childre n". In
Canada, the terms "top tether" with "lower un i­
versa l anchorages" (o r "lowe r universa l anchor­
age bars") a re used to descr ibe the system .
In other co untries the term "ISOFIX" is used to
desc ribe the lower anchorages .
Forward-facing chi ld restraints manufactured af­
ter September 1, 1999, are requ ired by U.S . fed­
era l regulations to comply with new child head
movement pe rformance requ iremen ts. These
new pe rformance req uir ements make a tether
necessary on most new ch ild seats.
Installing a c hild restraint t hat requires a top
tethe r withou t one can se riously impa ir the per­
fo rmance of the ch ild rest rai nt and its ab ility to
pro tect the ch ild in a co llision. I nstalling a ch ild
r estr aint tha t requi res a top tether wi tho ut the
top tether may be a vio lat ion o f state law.
Child restra int manufactu rers offe r LATCH lowe r
an chorages on t heir child sea ts w it h hook-on or
..,
305

u co ..... N r-­N .....
~ 0 co
A WARNING
Improper use of LATCH lower anchorages can
cause serious personal injury in an accident.
- Always carefu lly follow the child restra ints
manufacturer's instructions for proper in­
sta llation of the child restraint and proper
use of the lower anchorages or safety belts
in your vehicle.
- Never secure or attach any luggage or other
items to the
LATCH lower anchorages .
- Always read and heed the important infor­
mation about child restraints in this chapter
and
WARNINGS ¢ page 291, Child safety.
Installing a child restraint with LATCH
lower anchorages
Whenever you install a child restraint always fol­
low the child restraint manufacturer's instruc­
tions .
Fig . 2 4 9 Lower anchorages: p roper mount ing
Mounting
.,. Make sure the seatback of the rear seat bench
i s in the upr igh t position and securely latched
in place .
.,. Remove the covers to access the lower anchor ­
age brackets .
.,. Attach both hook -on connectors with the spring
catch release on the ch ild safety seat onto the
LATCH lower anchorage so that the connectors
lock into place
¢ fig . 249 .
.,. Pull on the connector attachments to make
s ur e they a re prope rly attached to the LA TC H
lower anchorage.
.,. Pull straps tight fo llowing the child restra int
manufacturer's instructions.
Ch ild s afe ty
Re leas ing
.,. Loosen the tension on the straps fo llow ing the
child restraint manufacturer's instructions.
.,. Depress the spring catches to release the an­
chorage hooks from the lower anchorages.
Remember: Use tethe r straps to help keep the
child restraint firmly in p lace .
A WARNING
-
Improper use of the LATCH system can in­
crease the risk of serious personal injury and
death in an accident.
- These anchors were developed only for child
safety seats using the "LATCH" system.
- Never attach other child safety seats, be lts
or other objects to these anchors.
- Always make sure that you hear a click when
latching the seat in place. If you do not hear
a cl ick the seat is not secure and co uld f ly
forward and hit the interior of the vehicle,
or be ejected from the vehicle .
A WARNING
Improper installation of child restraints wi ll
i ncrease the risk of injury in an accident.
- Always follow the child restraint system
manufacturer's instructions for proper in­
stallat ion of the chi ld restraint system and
proper use of tether straps as well as the
lowe r ancho rages or safety belts in yo ur ve­
h icle.
- Always read and heed the important info r­
mat ion a nd WARN INGS abou t ch ild safety
a nd the ins tallat ion of ch ild restraint sys­
tems ~ page 291 , Child safety.
307

u co ..... N r-­N .....
~ 0 co
-If you are unable to determine whether or
not a particular fuel blend meets the speci­
fications, ask your service station or its fuel
supplier.
- Do not use fuel for which the contents can­
not be identified.
- Fuel system damage and performance prob­
lems resulting from the use of fuels differ­
ent from those specified are not the respon­
sibility of Audi and are not covered under
the New Vehicle or the Emission Control
System Warranties .
- If you experience a loss of fuel economy or
driveability and performance problems due
to the use of one of these fuel blends, we
recommend that you switch to unblended
fuel.
Gasoline additives
A major concern among many auto manufactur­
ers is carbon deposit build-up caused by the type
of gasoline you use.
Although gasoline grades differ from one manu ­
facturer to another, they have certain things in
common. All gasoline grades contain substances
that can cause deposits to collect on vital engine
parts, such as fuel injectors and intake valves.
Al­
though most gasoline brands include additives to keep engine and fuel systems clean, they are not
equally effective .
Audi recommends using TOP TIER Detergent Gas­
oline. For more information on TOP TIER Deter­
gent Gasoline, please go to the official website
(www.toptiergas .com) .
After an extended period of using inadequate
fuels, carbon deposit build-ups can rob your
en­
gine of peak performance.
(D Note
Damage or malfunction due to poor fuel qual­
ity is not covered by the Audi New Vehicle
Limited Warranty.
Checking and Filling
Refueling
Fueling procedure
Fig. 253 Right rear s ide o f th e ve hicle : ope ning the fuel
filler door
Fig. 254 Fuel filler door with attached fue l cap
The fuel filler door is unlocked or locked by the
central locking system.
"' Press on the left side of the fuel filler door to
open
r::::>fig. 253.
"' Unscrew the tank cap counterclockwise.
"'Place the cap from above on the open fuel filler
door
r::::> fig. 254.
"'Insert the fuel pump nozzle all the way into the
fuel filler neck.
.,. Begin fueling. Once the fuel pump nozzle turns
off the first time, the fuel tank is full. Do not
continue fueling, or else the expansion space in
the tank will be filled with fuel.
"'After the fuel pump has switched off, wait five
seconds before removing it to allow the rest of
the fuel to finish dripping into the fuel tank.
"'Turn the fuel cap clockwise until you hear it
lock.
"' Close the fuel filler door and then press on the
left side until it latches .
The correct fuel type for your vehicle can be
found on a label located on the inside of the fuel
Iii>
311

Check ing and F illing
fi ller door . For additional information on fuel,
see
r=> poge 310.
For the tank capac ity in yo ur vehicle , refer to the
Technical Data
r:!> pog e 369.
To reduce the r isk of fuel leak ing out or vapors
escap ing , make sure that the fuel tank is closed
correct ly. Otherwise
thP ¢'4 i ndicato r light will
t ur n on.
I f the central lock ing system malfunct ions, the
fue l filler door may emergency release
r=> poge 313.
_& WARNING
An improper f ueli ng p rocedure and improper
hand ling of fue l can lead to exp losions, fires,
severe b urns and other injuries .
- Do not smoke and keep away from open
flames .
- T he ign it ion m ust be switched off when re ­
f ueling .
- Cell p hones, radio devices and other radio
equipment s hou ld always be switched off
when refueling . Electromagnetic rays cou ld
cause sparks and start a fire .
- If you do not insert the fue l pump nozzle a ll
the way into the filler tube, then fue l can
l eak out . Spi lled fue l can ignite and start a
fire.
- Never get into the vehicle when refueling. If
there is an exceptional situation where the
vehicle must be entered, close the door and
touch a metal surface before touching the
fuel pump nozzle again . This will reduce the
risk of electrostat ic discharge that can cause
flying sparks . Sparks can start a fire when
r efuel ing .
_& WARNING
We recommend that you do not t ransport any
fue l conta iners in t he ve hicle. Fue l cou ld leak
out of the container and ignite, espec ially dur ­
ing an accident. This can cause exp losions,
fires and injuries .
- If you must transport fuel in a fuel contain ­
er, please note the following:
312
- Always place a fue l container on the
ground before fill ing . Never fill the fuel
container with fuel while it is in or on the
vehicle . Electrostatic charge can occur
while refueling and the fuel vapors could i gnite .
- For fuel containers made of metal, the fuel pump nozzle must always maintai n
contact with the conta iner to reduce the
r isk of s tat ic charge.
- Insert the fuel pump nozz le as far as pos­
s ible into the fi lle r opening w hile refuel­
ing .
-Fo llow lega l requ irements when using,
stor ing and t ransporti ng f uel con ta iners.
- Make su re that the fuel containe r meets
t h e i nd ust ry standa rds, fo r example ANS I
o r ASTM F852 -86.
@ Note
- Remove fuel that has overflowed onto any
vehicle components immediately to reduce
the risk of damage to the vehicle.
- Never dr ive unt il the fuel tank is completely
empty . T he irregula r supply of fue l that re­
s u lts from that can cause eng ine misfi res.
Uncombus ted fuel will ente r th e exhaus t
system and increase the risk of damage to
the cata lytic converter .
@ For the sake of the environment
Do not overfill the fuel t ank, o therwise f uel
can leak o ut w hen the veh icle is warming up.
(D Tips
The fuel fille r doo r on your veh icle does not
l ock if you lock t he ve hicle from t he i nside us­
i ng the centra l locking switc h.

u co ..... N r-­N .....
~ 0 co
Fuel filler door emergency release
If the central locking system is faulty, the fuel filler door can be unlocked manually.
Fig . 255 Right side trim j)anel in the luggage compart­
ment: opening the trim panel
Fig. 256 Luggage compartment: fuel filler door emergency
release
The emergency opening mechanism is located
behind the right side trim panel in the luggage
compartme nt.
.,. Open the cover in the side pane l¢ fig. 255.
.,. Loosen the loop from the retainer and then pull
on the loop
carefully¢ fig . 256 ¢ Q) . The filler
door is released .
.,. Press on the left side of the fuel filler door to
open it
¢page 311, fig. 253.
(D Note
On ly pull on the loop until you feel resistance.
You will not hear it release. Otherwise you could damage the emergency release mecha­
nism.
Chec king and Filling
Emissions control
system
Cat alytic con verter
The vehicle may only be driven with unleaded
gasoline, otherwise the catalytic converter will be
destroyed.
Never drive until the tank is completely empty .
The irregu lar supply of fuel that results from that
can cause engine misfires. Uncombusted fuel will
enter the exhaust system, which can cause over­
heating and damage to the catalytic converter .
A WARNING
The temperature of the exhaust system is
hi gh, both when driv ing and after stopping
the eng ine.
-
- Never touch the exhaust tail pipes once they
have be come hot. This cou ld resu lt in burns.
- Do not park your veh icle over flammable
mate ria ls such as grass or leaves because
the high temperature of the emissions con­
trol system could start a fire.
- Do not app ly unde rbody protectant in the
exhaust sys tem area, beca use this increases
the risk of f ire.
On Board Diagnostic
System (OBD)
The On-Board Diagnostic System monitors the
engine and transmission components that influ­
ence emissions .
Fig. 257 Footwell on left s ide of th e veh icle: conn ect io n
port fo r the O n-Board D iagnost ic System (08D)
313

u co ..... N r-­N .....
~ 0 co
-To reduce the risk of electric shock and in­
jury, never touch the following components
when the engine is running or is being start­
ed :
- Ignition cable
- Other components in the electronic high-
voltage ignition system
- If you must check or perform work on the
engine while it is running:
- Set the parking brake first and then select
the
"P" selector lever position .
- Always proceed with extreme caution so
that clothing, jewelry or long hair do not
become caught in the radiator fan, fan
belt or other moving components or do
not come into contact with hot compo­ nents. Tie back long hair before beginning
work and do not wear cloth ing that can
hang down into the engine.
- Limit your exposure to exhaust and chemi­
cals to as short a time as possible
c::> & .
..&, WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of Cali­
fornia to cause cancer and birth defects and
reproductive harm. In addition, certain flu­
ids contained in vehicles and certain prod­
ucts of component wear contain or emit
chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm.
- Battery posts, terminals and related acces­
sories contain lead and lead compounds, chemicals known to the State of California
to cause cancer and reproductive harms.
Wash hands after handling.
(D Note
When filling fluids, be sure not to mix the flu­
ids up . Otherwise severe malfunctions and en­
gine damage will occur.
Checking and Filling
@) For the sake of the environment
You should regularly check the ground under
your vehicle in order to detect leaks quickly.
If
there are visible spots from oil or other fluids,
bring your vehicle to an authorized Audi deal­
er or authorized Audi Service Facility to be
checked .
Opening/closing the hood
The hood is released from inside the vehicle .
Fig. 258 Driver footwell : relea se lever
Fig. 259 Unlocked hood: lever
Make sure the wiper arms are not raised up from
the windshield . Otherwise the paint could be
damaged.
Opening the hood
.,. With the driver 's door open, pull the lever be­
low the instrument panel in the direction of the
arrow
c::, fig. 258.
.,. Raise the hood slightly c::> &.-
.. Press the lever c::, fig. 259 in the direction of the
arrow. This releases the hooks .
.,. Open the hood. ..,.
315

Wheels
Wheel bolts and rims
Wheel bolts
Wheel bolts must be clean and loosen/tighten
easi ly.
Rims
Rims with a bolted rim ring* or with bolted wheel
covers* consist of multiple pieces . These compo­
nents were bolted together using special bolts
and a special procedure . You must not repair or
d isassemble them
C> _&. .
_& WARNING
Wheel bolts that are tight ened or repaired in­
correctly can become loose and result in loss
of vehicle control, which increases the risk of
an accident. For the correct tightening specifi­
cation, see
e> page 356, Finishing.
-Always keep the wheel bolts and the
threads in the wheel hub clean and free of
grease.
- Only use wheel bolts that fit the rim.
- Always have damaged rims repaired by an
authorized Audi dealer or authorized Audi
Service Facility . Never repair or disassemble
rims yourse lf, because this increases the risk
of an accident.
Winter tires
Winter tires significantly improve the vehicle's
handling when driving in winter conditions . Be ­
cause of their construction (width, compound,
tread pattern), summer tires provide less trac­
tion on ice and snow.
"'Use winter tires on all four wheels .
"'Only use winter tires that are approved for your
vehicle .
"'Please note that the maximum permitted
speed may be lower with winter tires
e> & in
General information on page 325.
An author­
ized Audi dealer or authorized Audi Service Fa­
cility can inform you about the maximum per­
mitted speed for your tires .
"'Check the tire pressure after installing wheels
¢page 335.
340
The effectiveness of winter tires is reduced great­
ly when the tread is worn down to a depth of
0.16 in (4 mm) . The characteristics of winter
tires also decrease greatly as the tire ages, re­
gardless of the remaining tread.
@) For the sake of the environment
Reinstall summer tires at the appropriate
time, because they provide better handling
when roads are free of snow and ice. Summer
tires cause less road noise, tire wear and fuel
consumption .
(D Tips
You can also use all season tires instead of
winter tires. Please note that in some coun­
tries where winter tires are required, only
winter tires with the
& symbol may be per­
mitted.
Snow chains
Snow cha ins not only improve the driving in win­
ter road conditions, but also the braking.
"'Only install snow chains on the rear wheels.
"' Check and correct the seating of the snow
chains after driving a few feet, if necessary. Fol­
low the instructions from the manufacturer.
"'Note the maximum speed of 30 mph (SO km/
h). Note the local regulations.
Use of snow chains is only permitted with certain
rim/tire combinations due to technical reasons.
Check with an authorized Audi dealer or author­
ized Audi Service Facility to see if you may use
snow chains.
Use
fine-mesh snow chains. They must not add
more than 0 .53 in (13.S mm) in height, including
the chain lock.
You must remove the snow chains on roads with­
out snow . Otherwise, you could impair driving
ability and damage the tires .
_& WARNING
Using incorrect snow chains or installing snow
chains incorrectly can result in loss of vehicle
9"'