..,Audi recommends that you use
Audi Original Tires. If you would like to use different tires, please
note that the tires may perform
differently even if they are the
same size
i=:> &, .
..,If you would like to equip your
vehicle with a tire/rim combina
tion that is different from what
was installed at the factory, con
sult with an authorized Audi
dealer or authorized Audi Service Facility before making a pur
chase
i=:> &, .
Because the spare tire* is differ
ent from the regular tires instal
led on the vehicle (such as winter
tires or wide tires), only use the spare tire* temporarily in case of
emergency and drive carefully
while it is in use. It should be re
placed with a regular tire as soon
as possible.
Applies to: vehicles with all wheel drive: all four wheels must be
equipped with tires that are the
same brand and have the same construction and tread pattern so
that the drive system is not dam aged by different wheel speeds .
~ For this reason, in case of emer-
-~ gency, only use a spare tire* that
-0
"' \.) ..
Wheels
is the same circumference as the
regular tires.
&_ WARNING
-
-Do not use steel rims that are
17 inches or larger. Other
wise, damage to the vehicle
and an accident could result.
-Only use tire/rim combina tions and suitable wheel bolts
that have been approved by
Audi. Otherwise, damage to
the vehicle and an accident
could result.
-For technical reasons, it is not possible to use tires from oth
er vehicles -in some cases,
you cannot even use tires from the same vehicle model.
-Make sure that the tires you select have enough clearance
to the vehicle. Replacement
tires should not be chosen
simply based on the nominal
size, because tires with a dif
ferent construction can differ
greatly even if they are the
same size. If there is not
enough clearance, the tires or
the vehicle can be damaged
and this can reduce driving
safety and increase the risk of
an accident.
...
213
Wheels
be five 150 lbs. pas seng ers in
your vehicle, th e am ount of
a vail abl e cargo and lug gage
lo ad ca pac ity is 650 lb s.
(1400-750 (5
X 150) = 650
lb s.)
5. Determine the combined weight of lu ggage and c argo
bein g loaded on the vehi cle .
Th at w eight ma y not safel y
ex
ceed the a vail able car go and
luggage lo ad capac ity calc ul at
ed in St ep 4 .
6. If your vehicle will b e towing a
tr aile r, lo ad from your tr aile r
w ill b e tran sferr ed to your
v e
hi cle. C onsul t this manual t o
determin e how this re du ces
th e av ailab le cargo and lug
g age load capa cit y of your v ehi
cl e.
..,.Che ck th e tire sidewall
(c:::> pa ge 206, fig . 187) to det er
mine the de signated load rating
for a sp e cific tire.
Wheel bolts and rims
Wheel bolts
Wheel bolts must be clean and loosen/t ighten
easi ly .
Rims
Rims with a bolted rim ring* or w it h bolted whee l
covers " consist of mu ltip le pieces . These compo
nents were bolted together using specia l bolts
220
and a spec ia l proced ure. Yo u must not repair or
disassemb le them
i::> &. .
A WARNING
Wheel bo lts that are tightened or repaired in
correct ly can become loose and resu lt in loss
of vehicle contro l, wh ich increases the risk of
an accident . For the correct tighten ing spec ifi
cation,
see ¢ page 23 7, After changing a
whe el.
- Always keep the wheel bolts and the
threads in the wheel hub clean and free of
grease .
- Only use wheel bolts tha t fit the rim.
- Always have damaged rims repaired by an
author ized Audi dealer or authorized A udi
Serv ice Facility . Neve r repa ir o r disassemb le
rims you rself, because this increases the risk
of an a cciden t.
Winter tires
Win ter tires significant ly imp rove the veh icle's
handling when dr iv ing in winter conditions. Be
ca use of their construction (width, compound,
tread patte rn), s ummer ti res provide less trac
tion on ice and snow.
.,. Use winter tires on a ll four wheels .
.,. Only use winter tires that are app roved for yo ur
vehicle .
.,. Please note that the maximum permitted
speed may be lowe r with winter
tires¢ &. in
General information on page
205 . An author
ized Aud i dealer or authorized Aud i Serv ice Fa
cility can inform yo u about t he maximum per
m itted speed for your tires .
.,. Check the tire p ressure afte r insta lling wheels
¢ page 215 .
The effectiveness of wi nter tires is reduced g reat
l y when t he tread is wo rn down to a depth of
0.157 i n (4 mm). The cha ra cte ris tics of winte r
t ir es a lso decrease g rea tly as the t ire ages , re
gard less o f th e remaining t read.
a co ,...,
N
" N ,...,
0 00 <.,;) '
Emergency assistance
General information
.. Par k the vehicle as far as poss ible from moving
traff ic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a leve l surface .
It you are on a steep hill, be especially careful.
.. Set the parking brake .
.. Switch the emergency flashe rs on .
.. Set up the warn ing triangle C) page 233 .
.. Have the passengers exit the veh icle . They
sho uld move to a safe place, for example be
hind a guard rail.
_& WARNING
Follow the s teps given above. This is for your
protection and the for the safety of other d riv
ers .
Equipment
Warning triangle
App lies to: ve hicles with warning triangle
D
Fig. 193 Luggage compa rtment U d : wa rnin g tr iang le
The warning triangle placed in the vehicle at the
factory is located in the luggage compartment.
.. Turn the twist lock C) fig . 193 and pull the cover
downward to open the cover.
.. Remove the warning triangle from its holder.
The luggage compartment lid is only designed to
hold the warning triangle offered by the Audi
Genu ine Accessories program.
Em ergen cy as sis tanc e
Vehicle tool kit
Fig. 194 Lu ggage compartment: vehicle tool kit, tire mob i
lity kit and comp resso r
The vehicle tool kit, vehicle ja ck*, tire mobility
ki t* and compressor are stored in the luggage
compartment under the ca rgo floor cover .
.. Lift the cargo floor by the p lastic handle .
.. Turn the handle cou nter- clockwise and remove
the cover or the spare tire *.
A WARNING
Improper use of the vehicle jack can cause se
rious pe rsonal injuries.
-Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if yo u
use the hex head, potentially causing an ac
cident.
-The factory-supplied jack is intended only
for your vehicle model. Under no circum stances shou ld it be used to lift heavy
veh icles o r othe r loads; you risk injuri ng
yourse lf .
-Never start the engine when the vehicle is
raised, which could cause an accident.
-Support the vehicle securely with appropri
ate stands if wo rk is to be performed under
neath the vehicle; otherwi se, there is a po
t ential risk fo r injury .
-Never use the jack supplied with your Aud i
on another vehicle, particularly on a heavier
o n e. Th e jack is o nly sui tab le for u se on the
veh icle i t came wi th.
(D Tips
The vehicle jack* in your vehicle is mainte
nance-free.
233
Emergency assistance
-If the tire is too severely damaged, see an
authorized Aud i dealer or authorized Aud i
Service Facility for assistance.
@ For the sake of the environment
You can give the used tire sealant bottle to an
authorized Audi dealer or authorized Audi
Serv ice Facility for disposal.
(D Tips
Remember to obtain a new bottle of sealant
from an authorized Audi dealer or authorized
Audi Serv ice Facility after repairing a tire.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
.,. After you exper ience a tire fa ilure, pull the car
well away from moving traff ic and try to reach
level ground
before you stop ¢.&, .
.,. All passengers sho uld leave the car and move
to a safe location (for instance, be hind t he
guardrail) ¢.&, .
.. Engage the parking brake to prevent your vehi
cle from rolling
unintentionally ¢.&, .
.. Move selector lever to position P ¢ A-
.. If you are towing a trailer, unhitch the trailer
from your veh icle .
.,. Take the jack and the spare tire* out of the lug
gage compartment
ca> page 233 .
.8, WARNING
You or your passengers could be inju red w hile
chan gin g a wheel if you do not follow these
safety precautions:
- If you have a flat ti re, move a safe d ista nee
off th e road. Turn off the engine, turn the
emergency flashers on and use other warn
ing devices to alert other motorists .
- Make sur e that passengers wait in a safe
place away from the vehicle and we ll away
from the road and traffic.
236
- To help prevent the vehicle from moving
suddenly and possibly s lipping off the jack,
always fully set the parking brake and block
the front and back of the wheel diagonally
opposite the wheel being changed. When
one front wheel is lifted off the ground,
p lacing the Automat ic Transmission in P
(Pa rk) w ill
not prevent the vehicle from
mov ing.
- Before you change a wheel, be sure the
ground is level and firm. If necessary, use a
sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tire in the lu ggage com
pa rtment
¢page 134 .
(D Tips
Before changing the wheel, you must activate
the jacking mode, so that the automatic con
trols for the Adaptive Air Suspension* do not
make it more difficult to lift the vehicle with
the jack
ca> page 238 .
Changing a wheel
When you change a wheel, follow the sequence
described below step-by-step and in exactly that
order .
1. Act ivate the vehicle jack mode* ca> page 238 .
2. Remove the decorative wheel cover* or the
wheel bolt caps*. For more details see also
¢ page 23 7, Decorative wheel covers or
¢ page 237, Wheels with wheel bolt caps.
3. Loosen the wheel bolts ¢ page 238.
4. Locate the proper mounting point for the
jack and alig n the jack below that po int
¢ page 238 .
5. Raise the car with the jack ca> page 238.
6. Remove the wheel with the flat tire and then
install
the spare ca> page 240.
7. T ighten all whee l bolts lightly.
8 .
Lower the vehicle with the jack.
9. Use the wheel bolt wrench and
firmly tighten
all wheel
bolts ¢ page 238.
10. Replace the decorat ive wheel cover* or the
wheel bolt caps*.
11. Deact ivate the vehicle jack mode* in the
MM I:
ICARI function button > (Ca r)* systems .,.
a co ,...,
N
" N ,...,
0 00 <..:l '
control button > Servicing & check s > Air
s u sp .: jack mode > Off .
The vehicle jack mode* swi tches off automatical
l y at speeds above 6 mph ( 10 km/h).
_& WARNING
Always read and follow all WARNINGS and in
formation
c:> ,1,. in Raising the vehicle on
page 239
and c:> page 241.
After changing a wheel
A wheel change is not complete without the do
ing the following.
.,. Always store the vehicle tool kit, the jack* and
the replaced tire in the luggage compartment
c:> page 134.
... Check the tire p re ssu re on the spare wheel im
mediately after mounting it.
... As soon as possible, have the tighten ing tor
que s
on all wheel bolts checked with a torque
wrench. The correct tightening torque is 90 ft
lbs (120 Nm).
.,. Have the flat tire replaced as soon as possib le.
@ Tips
- If you notice t hat the wheel bolts are cor
roded and diffic ult to turn wh ile changing a
tire, they should be rep laced before yo u
chec k the tightening torque.
- Drive at reduced speed until you have the
tightening torques chec ked.
- After changing a wheel, the tire pressure in
all four tires must be checked/corrected and
the tire pressure mon itor ing indicator must
be stored in the MM I
c:> page 224,
c:> page 226 .
Emergen cy as sis tanc e
Decorative wheel covers
Applies to: vehicles with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts.
F ig. 1 98 Changing a wheel: Removing the whee l cover
Removing
... Insert the hoo k (provided w ith the vehicle tool
kit) in the hole in the wheel hub cover.
... Pull off the decorati ve w heel co ve r c:> fig. 198 .
Wheels with wheel bolt caps
Applies to: vehicles with wheel bolts with caps
The caps must be removed first from the wheel
bolts before the bolts can be unscrewed.
Fi g. 199 Cha ng ing a whee l: remov ing the wheel bolt caps
Removing
.,. Push the pla st ic clip (prov ided with the vehicle
too l kit) over the wheel bolt cap until the inner
reta iners on the clip al ign with the edge of the
cover.
... Remove the cap with the pla stic clip (vehicle
too l kit)
c:>fig. 199.
Refitting
.,. Place the caps over the whee l bolts and push
them back on.
2 37
Emergency assistance
The caps are to protect and keep the whee l bolts
clean.
Loosening and tightening the wheel bolts
Th e wheel bolts must be loosened b efore raising
the vehicle.
F ig . 2 00 Cha ngin g a w hee l: l oosening t he w heel bol ts
Loosening
.,. Slide the wheel wrench onto the wheel bolt as
far as it w ill go .
.,. Take t ight hold of the end of the wrench handle
and t urn the whee l bolts
counter -clockwise
about one single t ur n in t he d irec tion of ar row
¢ fig . 200.
Tightening
.,. Slide the wheel wrench onto the wheel bolt as
far as it w ill go .
.,. Take t igh t hold of the end of the wrench handle
and tu rn ea ch whee l bolt
clockwi se u ntil it is
sea ted.
_& WARNING
- Do not u se force or hurry when changing a
whee l
-you can ca use the vehicle to s lip off
th e jac k and cause serious pe rsonal injur ies .
-Do not loosen the whee l bolts more than
one turn
before you raise the vehicle with
t h e jac k.
-You risk an i njury.
(D Tips
- N ever use the he xag onal socket in the han
dle of the screwd river to loosen o r tighten
the w heel bolts .
- If a whee l bolt is very tigh t, you m ay fi nd i t
eas ier to loosen by carefully pus hing down
238
on the end of the whee l bolt wrench with
one foot only. As you do so, ho ld on to the
car to keep your balance and ta ke care not
to slip .
Raising the vehicle
The vehicle must be lifted with the jack first be
fore the wheel can be removed.
Fig . 201 Sill pa nels: marki ngs
.,, ..,
0
---"rn; S!~~;::---~
Fig. 20 2 S ill: p osit io nin g the ve hicle jack
.,. Ac tiva te the veh icle jack mo de* in the MMI:
!CAR I function button> (Car )* systems cont rol
but ton >
Servicing & che cks > Air su sp .: jack
mode > On .
.,. Engage the parking brake to prevent your veh i
cle from rolling uninte ntionally .
.,. Move the selector lever to position P .
.,. Find the marking (imprint) on the sill that is
nea rest the w heel that will be changed
¢ fig. 201 . Behind the marking, there is a lift
ing point
on t he sill fo r the ve hicle jack .
.,. Applies to: vehicles with a s ill: Remove the cov
er fro m the sill before lifting the vehicle wi th a
veh icle
ja ck¢ page 239.
.,. Tur n the vehicle jack located un der the lifting
point o n the s ill to raise the jack unt il its
arm @
~ fig. 202 is locate d under the d esignated plas-
tic
mount ¢ .&,¢(D. II>
Emergency assistance
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang
ing the wheel .
Fig. 204 Changing a wheel: using the screw driver handl e
(wit h th e blade re m oved) to turn the bol ts
F ig . 205 Changing a wheel: alignment p in inside t he top
hole
Afte r you have loosened a ll w heel bo lts and
raised t he vehi cle off the ground, remove and re
p lace the whee l as fo llows:
Removing the wheel
• U se the hexagonal so cket in the screwdriver
handle
t o comple tely remove the topmost
whee l bolt and set it aside on a
clean surfa ce
¢ fig. 204 .
• Screw the th readed end of the alignment pin
from the tool kit hand-tight into the empty bolt
hole¢ fig. 2051> .
• Then remove the other wheel bolts as described
above.
• Takeoff th e wheel leav ing the a lignment pin in
the bo lt ho le
¢ 0 .
l) Applies to vehicles with ceram ic brake rotors*: Use a sec
ond alignment
pin* (stored in th e spa re whee l well mo ld
ing) for the lower ho le, fo llowing t he descr iption for the
first alignment pin .
240
Putting on the spare wheel
• Lif t the sp are whee l and caref ully slide it over
t he alignment p in to guide it in place
¢ (D .
• Use the hexagonal socket in the sc rewdr iver
ha nd le to screw in and tighten a ll w heel bolts
slightly.
• Remove the alignment pin and insert and t ight
en the remaining w heel bo lt slight ly like the
rest.
• Tu rn the jack hand le co unte r-clockw ise to lowe r
t he vehicle unt il t he jac k is f ully re leased.
• Use the w heel bo lt wren ch to tighten a ll wheel
bolts fi rm ly¢
p age 238. Tighten them cross
wise,
from one bo lt to the (a pprox imately) op
posite one, to keep the whee l centered.
([» Note
When remov ing o r installin g the wheel, the
rim co uld hit the brake rotor/ce ramic brake
r otor * and damage t he rotor . Work carefully
and have a second person he lp you.
(D Tips
N eve r use the he xagonal socket in the han dle
of the sc rew drive r to loosen or t ig hten the
whee l bolts.
- Pull the reversible blade from the screwdr iv
er before yo u use t he hexagona l soc ket in
t h e handle to t urn the whee l bolts.
- When mounti ng tires with
unidirectional
tread design
make sure the tread pattern is
pointed the right
way¢ page 241.
- The wheel bolts sho uld be clean and easy to
t u rn. Check fo r dirt and corrosion on the
mating surfaces of both the wheel and t he
hub. Remove all d irt from these s urfaces be
fore remounti ng the whee l.
a co ,...,
N
" N ,...,
0 00 <.,;) '
Tires with unidirectional tr ead design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare t ire with a tread pattern in
tended fo r use in a specific direction, please note
the following:
- The direction of rotat ion is marked by an arrow
on the side of the tire .
- If the spare tire has to be installed in the incor
rect direction, use the spare tire only tempora
rily s ince the tire will not be able to achieve its
opt imum performance character istics with re
gard to aquaplaning, noise and wear.
- We recommend that you pay particular atten
t ion to this fact during wet weather and that
you adjust your speed to match road condi
tions.
- Replace the flat tire with a new one and have it
installed on your vehicle as soon as possible to
restore the handling advantages of a unidirec
tiona l tire .
Notes on wheel changing
Please read the information ~ page 212, New
tires or wheels
if you are going to use a spare tire
which is different from the tires on your vehicle.
After you change a tire:
- Check the tire pressure on the spare tire im
mediately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos
sible by your authorized Audi dealer or a
qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lbs (120 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire ,
they should be replaced before you check the
tightening torque.
Emergency assistance
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi
ble. Remount the wheel cover.
Until then , drive with extra care and at reduced
speeds.
A WARNING
- If you are going to equip your vehicle with
tires or rims which differ from those which
were factory installed, then be sure to read the information
r=> page 212, New tires or
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit are
properly secured in the luggage compart
ment and are not loose in the passenger
compa rtment.
- In an accident or sudden maneuver they
could fly forward, injuring anyone in the ve
h icl e.
- Always store damaged wheel, jack and tools
securely in the luggage compartment. Oth
erwise, in an accident or sudden maneuver
they could fly forward, causing injury to pas
sengers in the vehicle .
Spare tire
Space-saving spare tire
App lies to : vehicles wit h spare tire
Fig. 206 Luggage compartment: space-sav ing spare tire
The spare tire is intended for short-term use on-
-
ly. Have the damaged tire checked and, if neces
sary, replaced by an authorized Audi dealer or au
thorized Audi Serv ice Facility as soon as possible .
..,.
241