-If the hood is not latched completely, it
could fly up while you are driving and ob
struct your vision.
Engine compartment overview
The most important check points.
Checking and Filling
Fig. 268 Typical location of the reservoir a nd t he engine o il filler ope ning
(!) Washer fluid reservoir (O) c::> page 332
@ Jump start po int( +) under a cover,(-) w ith
hex head screw
¢page 332 c:>page 374
@ Engine oil filling opening (
c:> page325
® Coolant expansion tank (- L) c::> page 329
® Brake fluid reservoir ((0) c::> page 330
The location of the engine oil filling opening and
the coolant expansion tank ¢
fig. 268 (items@
and@) may differ depending on the engine ver
sion .
_& WARNING
-Read and follow all WARNINGS before check-
in g anything in the engine compartment
c:> page 323.
Engine oil
Engine oil specifications
The engine oil used must conform to exact speci
fications.
The service interval display in the instrument
cluster of your vehicle will inform you when it is
time for an oi l change . We recommend that you
have your oil changed by an authorized Audi Serv-
ice Advisor.
.,..
325
Checking and Filling
Charging the vehicle battery
Fig. 272 Engine co mpa rtment : connec tors for a c harger
and jump start cab le s
Req uirement: only use chargers with a m aximum
c hargi ng vo lta ge of 30 amp s/14.8 Volt s.
The
vehicle battery cables remain connected .
.,. Read the warnings c> .&. in General warnings
about batteries on page 331
and c> ,&. .
.,. Switch off the ignition and all electrical equip
ment .
.,. Open the hood 9 page 324 .
.,. Open the red cover on the positive terminal
c>fig. 272 .
.,. Clamp the charger terminal clamps to the jump
s ta rt pin s
according to the instruct ions . (pin
under the red cover = "positive ", p in with hex
agonal head= "negative ") .
.,. Inse rt the powe r cable for the charg ing device
i nto the socke t and switch the dev ice on .
.,. At the end of the charging process , switch the
charger off and pull the power cab le out of the
socket .
.,. Remove the charger terminal clamps.
.,. Close the red cover on the positive terminal.
.,. Close the hood c> page 324 .
A WARNING
-A highly explosive mixtu re of gases can form
when cha rging batter ies. On ly charge the
vehicle batte ry in well-ven tilated areas.
- A drai ned vehicle battery can freeze at tem
peratu res a round 32
QF (0 QC). A froze n or
thawed veh icle bat tery must not be charged
and must not be used anymore. The ba ttery
housing can crac k and battery acid can leak
o ut if ice forms, wh ich increases the r isk of
an exp losion and chemical burns. Contact an
332
author ized Audi dealer or authorized A udi
Service Facility for more information.
- Do not connect or disconnect the charging
cable whi le charging because this increases
the risk of an explos ion.
@ Tips
- Only charge the vehicle battery t hrough the
connect ions in the engine compartme nt.
- Read all of the manufacturer's instructions
for the charger before charging the vehicle
battery.
Windshield washer system
Fi g. 2 7 3 Engine compar tm ent: washer flui d res ervoir cap
The windshield washer fluid reservoir¢ contains
t he cleaning solution for the windshield and th e
headlight washer system *
c> page 325, fig. 268 .
The reservoir capaci ty can be found in
c> page 381.
To reduce the risk of lime scale deposits on the
spray no zzles, use clean water with low amounts
of calcium . Always add w indow cleaner to the wa
ter . When the outside temperatures are cold, an
anti -freezing agent should be added to the water
so that it does not freeze .
(D Note
-The concentration o f ant i-freez ing agent
must be adjusted to the ve hicle operat ing
conditions in the respective climate . A con
cent ration t hat is too high can lead to vehi
cl e damage.
- Never add radiator anti-freeze or other addi
t ives to the washer fluid.
Emergency situations
Emergency situations
General
This chapter is intended for trained emergency crews and working personnel who have the nec
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
(D Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine con be started by con
necting it to the battery of another vehicle.
If the engine should fail to start because of a dis
charged or weak battery, the battery can be con
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of sufficiently large cross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated terminal
clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black.
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in
jury. Follow the instructions below for
safe
handling of your vehicle's battery.
-Always shield your eyes and avoid leaning
over the battery whenever possible.
-A dead battery can freeze at temperatures
around 32 °F (0 °C) . If the vehicle battery is
frozen, you must thaw it before connecting
the jump start cables.
If you do not, this in-
374
creases the risk of an explosion and chemi
cal burns. After jump starting the vehicle,
drive to an authorized Audi dealer or author ized Audi Service Facility immediately to
have the vehicle battery checked.
- Do not allow battery acid to contact eyes or
skin . Flush any contacted area with water
immediately.
- Improper use of a booster battery to start a
vehicle may cause an explosion .
- Vehicle batteries generate explosive gases.
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery.
- The voltage of the booster battery must also
have a 12-Volt rating. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial
ly different
"Ah" rating may cause an explo
sion and personal injury.
- Never charge a frozen battery. Gas trapped
in the ice may cause an explosion.
- Never charge or use a battery that has been
frozen. The battery case may have be weak
ened.
- Use of batteries of different voltage or sub
stantially different capacity (Ah) rating may
cause an explosion and injury. The capacity (Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
r=:> poge 323.
([) Note
-Applying a higher voltage booster battery
will cause expensive damage to sensitive electronic components, such as control
units, relays, radio, etc.
- There must be no electrical contact between
the vehicles as otherwise current could al
ready start to flow as soon as the positive
(+) terminals are connected.
@ Tips
The discharged battery must be properly con
nected to the vehicle's electrical system .
When jump starting or charg ing the battery,
never connect the negative ground cable to
the battery negative post because the battery
manager system must be able to detect the
battery's state of charge. Always connect the
negative ground cable to the negative ground
post of the battery manager control unit.
Using the jump start
cable
Both jump start cables must be connected in the
correct order!
Fig. 295 Engine compartment: connec tors for jump start
cables and a charger
Fig. 296 Ju mp starting us ing a battery in another vehicle:
@ -providing current, @-drained
The procedure described below for connecting
jumper cables is intended to prov ide a jump start
for your vehicle .
Vehicle with discharged battery
•Turnoff lights and accessories, move the auto
matic transmission* selecto r lever to N (Neu
tral) or P (Par k), and set the park ing brake.
Emergency situations
Connecting the positive cable (red) to the
positive terminal
• Open the red cover on the positive terminal
c:>fig. 295 .
1. Secure one end of the positive cable (red) to
the jump start pin
c:> fig. 296 (D (pin under
the red cover = "posit ive") on the vehicle that
needs to be started @.
2. Secure the other end of the positive cable
(red) to the positive termina l@ on the
bat
tery provid ing the current @.
Connecting the negative cable (black) to the
negative terminal
3. Secure one end of the negative cable (black)
to the nega tive term inal @ on the battery
that is providing the current @.
4. Secure the other end of the negative cable
(black) to the jump start
pin @ (hex head pin
= "negative") on the vehicle that needs to be
started @.
Starting the engine
• Start the engine on the vehicle providing the
jump start @and let it run at idle.
• Now start the engine on the vehicle with the
drained battery @.
• If the engine does not start, stop the starting
procedure after 10 seconds and then repeat it
after approx imately 30 seconds.
• Remove the cables when the engines are run
ning. Remove them in reverse order from the
way they were installed.
• Close the red cover on the positive terminal.
T he battery is vented to the outside to prevent
gases from enter ing the vehicle interior . Make
sure that the jumper clamps are well connected
with their
metal parts in full contact with the
battery terminals.
_& WARNING
-To avoid serious personal injury and damage to the vehicle, heed all warnings and instruc
tions of the jumper cable manufacturer. If in
doubt, call for road service.
-Jumper cables must be long enough so that
the vehicles do not touch .
..,_
375
Emergency situations
-When connecting jumper cables, make sure
that they cannot get caught in any moving
parts in the engine compartment.
-Do not bend over the batteries -danger of
chemical burns!
-The battery cell locking screws must be
tightened securely.
-Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c> page 323.
(D Note
Improper hook-up of jumper cables can ruin
the generator.
- Always connect POSITIVE(+) to POSITIVE
(+), and NEGATIVE(-) to NEGATIVE(-)
ground post of the battery manager control
unit.
- Check that all screw p lugs on the battery
cells are screwed in firmly. If not, tighten
plugs prior to connect ing clamp on negative
battery terminal.
-Please note that the procedure for connect
i ng a jumper cable as described above ap
plies specifically to the case of your vehicle
being jump started . When you are giving a
ju mp start to another vehicle, do
not con
nect the negative (-) cable to the negative
(-) terminal on the discharged batte ry @
c> fig. 296. Instead, securely connect the
negative( -) cab le to either a solid metal
component that is firm ly bolted to the en
gine block or to the engine block itself. If
the battery that is being charged does not
vent to the outside, escap ing battery gas
could ignite and explode!
Towing with a tow truck
General hints
Your Audi requires special handling for towing.
The following information is to be used by com
mercial tow truck operators who know how to op
erate the ir equipment safely.
-Never tow your Audi, towing will cause dam
age to the engine and transmission.
376
-Never wrap the safety chains or winch cables
around the brake lines .
- To prevent unnecessary damage, your Audi
must be transported with a flat bed truck .
- To load the vehicle on to the flat bed, use the
towing loop found in the vehicle tools and at
tach to the front or rear anchorage
i:>page 376 and i:>page 377 .
A WARNING
A vehicle being towed is not safe for passen
gers. Never allow anyone to ride in a vehicle
being towed, for any reason.
Front towing loop
Only install the front towing loop when it is
needed.
Fig. 297 F ront bumper: installing the towing loop
The threaded opening for the towing loop is lo
cated on the right s ide of the front bumper.
.,. Remove the towing loop from the vehicle too l
ki t
c> page 360 .
.,. Press the cap inward with brief, forceful p res
sure
c> fig. 297 . The cap will loosen from the
bumper .
.,. Insert the towi ng loop all the way into the
threaded opening and tighten it with a wheel
wrench.
.,. After using, place the towing loop back in the
vehicle tool kit .
A WARNING
If the towing loop is not tightened until it
stops when installing, the threads may be
pulled out when towing the vehicle and that
could cause an accident.
-
a co .... N ..... N .... 0 0
3 co
Emergency call f unction
Au di connect emergency ca ll and service . 202
E me rgency flashe rs . . . . . . . . . . . . . . . . . . . . 56
Emergency starting . . . . . . . . . . . . . . . . . . . 374
E m issions cont rol sys tem . . . . . . . . . . . . . . 32 2
E nergy management . . . . . . . . . . . . . . . . . . 151
Eng ine
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Start/Stop system . . . . . . . . . . . . . . . . . . . . 85
Starting/stopping . . . . . . . . . . . . . . . . . . . . 83
Starting w it h jumper cables . . . . . . . . . . . 374
Eng ine compartment . . . . . . . . . . . . . . . . . . 323
Opening and clos ing the hood . . . . . . . . . . 324
Safety precautions . . . . . . . . . . . . . . . . . . . 323
E ng ine oi l . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Adding . ... ... .. .. ..... ... .. .. .... . 327
Changing . . . . . . . . . . . . . . . . . . . . . . . . . . 328
Checking the oil leve l . . . . . . . . . . . . . . . . . 327
Consumption . ............. .. .. .... .
D. t· k lpS IC .. ... ............. ...... ... .
327
327
O il consumption . . . . . . . . . . . . . . . . . . . . . 326
Specification and viscos ity . . . . . . . . . . . . . 325
T empe rature d isp lay . . . . . . . . . . . . . . . . . . 11
Eng ine sound . . . . . . . . . . . . . . . . . . . . . . . . 134
Eng ine Start/Stop mode
refer to Start/Stop system . . . . . . . . . . . . . 87
E nter ing cha racters/numbers (speller) . . . . 162
Enter ing letters (speller) . . . . . . . . . . . . . . . 162
E n terta inment s liding me nu . . . . . . . . . . . . 160
E ntry/ex it lighting . . . . . . . . . . . . . . . . . . . . . 56
Environment Proper disposal of drained engine o il ... .
Unleaded fuel . .. ........... .. .. .... .
E S C
.. .. .. .. ... .. .. ..... ... .. .. .... .
Hill descent assist ... .... ... .. .. .... .
Offroad mode ... .. .. .... ... .. .. .... .
Sport mode 328
315
1 46
148
147
147
E v asive steering suppo rt . . . . . . . . . . . . . . . 12 1
Event Data Recorder (EDR) . . . . . . . . . . . . . 153
Expanded view . . . . . . . . . . . . . . . . . . . . . . . . 1 5
E xterio r ligh ting . . . . . . . . . . . . . . . . . . . . . . . 54
Exterior mirrors . . . . . . . . . . . . . . . . . . . . . . . 58
E xternal voice operat ion.... ... .. .. .... . 173
Index
F
Factory default settings
Multi Media Interface . . . . . . . . . . . . . . . . 249
Fader (sound) . . . . . . . . . . . . . . . . . . . . . . . . 252
Fastening Booster seats . . . . . . . . . . . . . . . . . . . . . . . 305
Convertib le child safety seats . . . . . . . . . . 303
I n fan t seats . . . . . . . . . . . . . . . . . . . . . . . . 301
Fast forwarding/rewind ing (a udio/video
file) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
F ast forwarding ( aud io/v ideo file) . . . . . . . . 236
Fast route
Favorites Media 211
239
Navigation . . . . . . . . . . . . . . . . . . . . . . . . . 206
Telephone. . . . . . . . . . . . . . . . . . . . . . . . . . 180
F ile formats (media drives) . . . . . . . . . . . . . 242
Floor ma ts ..... ... .. ................ .
Foot peda ls . .... .. ................. . . 259
259
F o r the s ake o f th e e nv ironmen t
E nvironmenta lly-friend ly driving . . . . . . . . 80
Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Leaks ... .. .... .. .. ... .. ..... ... .. .. 324
Warming up the engine . . . . . . . . . . . . . . . . 83
F ree text search . .. .. .. .
............ ..
Media .. .. .... .. .. .... . ..... ... .. ..
Navigation .... .. ... .. .. ..... ... .. . .
Radio
. . .. .. ' . .. .. ... .. ..... ... .. . .
Telephone . .... .. ................. . .
F ree ze p ro tect ion 164
2 38
205
223 184
Coo lant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 9
Freq uency band . . . . . . . . . . . . . . . . . . 222, 225
Front airbags Desc ription . . . . . . . . . . . . . . . . . . . . . . . . . 275
How they work . . . . . . . . . . . . . . . . . . . . . . 281
F rontal collisions and the laws o f physics . . 264
Front passenger 's doo r eme rgency locking . . 42
Front seats Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Child restra ints in the front seat . . . . . . . . 272
also refer to Seats . . . . . . . . . . . . . . . . . . . . 65
Fuel Additives
.. .... .. ................. .. 315
B lended gasoline . . . . . . . . . . . . . . . . . . . . 315
Current consumpt io n . . . . . . . . . . . . . . . . . .
17
D iesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
391
Index
Fue l filler neck . . . . . . . . . . . . . . . . . . . . . . 317
F ue l gauge . . . . . . . . . . . . . . . . . . . . . . . 10, 12
Fue l tank capac ity . . . . . . . . . . . . . . . . . . . 381
Gasoline . .. .. ...... ......... .... ... 315
Gasoline additives . . . . . . . . . . . . . . . . . . . 316
Octane rating . . . . . . . . . . . . . . . . . . . . . . . 315
Recommendation . . . . . . . . . . . . . . . . . . . . 315
Saving fue l . . . . . . . . . . . . . . . . . . . . . . 80, 134
Fueling Fue l gauge . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Fuel tank capac ity . . . . . . . . . . . . . . . . . . . 381
O pening the fuel fille r door . . . . . . . . . . . . 317
Fuses Assignment . . . . . . . . . . . . . . . . . . . . . . . . 370
Replac ing . . . . . . . . . . . . . . . . . . . . . . . . . . 369
G
Garage doo r opener
refer to Homelink . . . . . . . . . . . . . . . . . . . . 52
Garment hoo ks . . . . . . . . . . . . . . . . . . . . . . . . 69
Gas discharge lamps . . . . . . . . . . . . . . . . . . . 373
Glossary of tire and loading terminology .. 336
Glove compartment . . . . . . . . . . . . . . . . . . . . 69
V al et par kin g f unction . . . . . . . . . . . . . . . . . 5 1
Gross Vehicle Weight Rat ing (GVWR) . . . . . 380
H
Handsfree . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
H ead -up display . . . . . . . . . . . . . . . . . . . . . . . 24
H eadlight range control system . . . . . . . . . . 54
Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
C lean ing . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
H eadlight range control system . . . . . . . . . 54
Washer system . . . . . . . . . . . . . . . . . . . . . . 60
Head restraints . . . . . . . . . . . . . . . . . . . . 66, 25 7
Adj usti ng . . . . . . . . . . . . . . . . . . . . . . . . . . 257
H ea ting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
H eavy clothing and safety belts . . . . . . . . . . 265
High beams . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Hi ll descent ass ist. . . . . . . . . . . . . . . . . . . . . 14 8
Hi ll descent control . . . . . . . . . . . . . . . . . . . . 94
H ill hold ass ist . . . . . . . . . . . . . . . . . . . . . . . . 89
also refer to Hill hold ass ist . . . . . . . . . . . . 89
H ome address .. .. .. .............. 206, 2 12
392
Homelink . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Hor n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
How are child restraint system anchors relat-
ed to c hild safety . . . . . . . . . . . . . . . . . . . . . 309
How many a irbags does my vehicle have? . . 278
How safety belt pre tensioners work . . . . . . 269
I
Imbalance (whee ls) . . . . . . . . . . . . . . . . . . . 342
Immobilize r . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Important things to do before dr iv in g . . . . 254
Importing and expo rting (contacts) . . . . . . 185
I mprope rly wo rn safety bel ts . . . . . . . . . . . 269
Ind icator lights . . . . . . . . . . . . . . . . . . . . . . . . 25
Airbag system . . . . . . . . . . . . . . . . . . . . . . 283
PASS ENG ER A IR BAG . . . . . . . . . . . . . . . . . 283
Infant seats . . . . . . . . . . . . . . . . . . . . . . . . . 301
I np ut
U sing the M MI touch . . . . . . . . . . . . . . . . . 158
U sing the speller . . . . . . . . . . . . . . . . . . . . 162
I np ut level (media) . . . . . . . . . . . . . . . . . . . . 239
Inspection interva l . . . . . . . . . . . . . . . . . . . . 333
Installing the upper te ther s trap on t he an
c h o rage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
Instrument cluster . . . . . . . . . . . . . . . . . . . . . 10
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Instrument illumination . . . . . . . . . . . . . . . . 58
Interior lighting . . . . . . . . . . . . . . . . . . . . . . . 57
Internet
refer to Aud i connec t (Infotainmen t) . . . . 188
Internet radio . . . . . . . . . . . . . . . . . . . . . . . . 232
Interval mode (wipers) . . . . . . . . . . . . . . . . . . 60
i Phone
refer to Aud i m usic interface . . . . . . . 233, 234
J
Jukebox 229
Jump-start ing . .. .. .. .. .. ........... .. 374
Jump start cable . .. .. .. .. ........... .. 375