2018 AUDI A4 warning light

Installing the upper tether strap on the
anchorage
Appliesto:Sedan
Fig. 258 Tether strap: proper routing and mo unting
Applies to: allroad
Fig. 259 Tether strap: pro per rout ing and mount ing
Installing the tether strap
• Release or deploy the tether strap on the child
restraint according to the child restraint manu­
facturer's instructions .
• Guide the upper tether strap under the rear
head restraint (raise the head restraint if neces­
sa ry) . For child restraints with V-tether straps,
always make sure that the head restraint guide
rods do not interfere with any part of the top
tether strap.
• Applies to: Sedan: Tilt the recess flap up to ex ­
pose the anchor bracket.
• Applies to: Sedan : Attach the tether strap an­
chorage hook into the opening of the tether an ­
chorage.
• Applies to: allroad: Guide the upper tether
strap into the rear cargo area and slide the
tether strap hook over the anchor bracket .
•Pullon the tether strap hook so that the spring
catch of the hook engages .
• Tighten the tether strap firmly fo llow ing the
child restraint manufacturer's inst ruct ions.
Child safety
Releasing the tether strap
• Loosen the tension following the child restra int
manufacturer's instructions.
• Depress the spring catch on the hook and re­
lease it from the anchorage.
(D Note
If you leave the child restraint with the tether
strap firmly installed for several days, this
could leave a mark on the upholstery on the
seat cushion and backrest in the area where
the tether strap was installed . The upholstery
would also be permanently stretched around
the tether strap . T hi s applies espec ially to
le ather seats.
Using tether straps on rearward-facing
child restraints
Currently, few rear-facing child restraint systems
come with a tether. Please read and heed the
child restraint system manufacturer's instruc­
tions carefully to determine how to properly in­
stall the tether.
_&. WARNING ~
A child in a rearward-facing child safety seat in sta lled on the front passenger seat will be
se riously inju red and can be killed if the front
airbag inflates -even w ith an Advanced Air­
bag System.
- The inflating airbag will h it the child safety
seat or infa nt carrier with great force and
will smash the child safety seat and child against the backrest, cente r armrest, or
door.
- If you must install a rearward facing child
safety seat on the front passenger seat be­
cause of exceptional circumstances and the
PASSENGER AIR BAG OFF "1; light does not
come on and stay on, immediately install
the rear-facing child safety seat in a rear
seating position and have the a irbag system
i n spected by your Audi dealer.
313

Check ing and F illing
"' Position the bottle on the filler tube and turn
the bottle clockwise unti l it stops turning.
"' Press lightly aga inst the bottom of the bott le
to empty it. Continue pressing the bottom of
the bottle until it is empty or unti l fluid stops
flowing into the tank .
"' Remove the bottle and seal the filler neck
¢ page 322, Completing AdBlue refill .
0 Note
Only use refill bottles that are approved for
your vehicle. Us ing other systems can ca use
Ad Blue to leak.
-You can obta in refill bottles from an author­
i zed Audi dealer or authorized A udi Service
F ac ility.
- A pe rm itted refill bottle conta ins approxi­
mately 0 .5 gallon ( 1.9 liters) of Ad Blue.
Completing AdBlue refill
Applies to: vehicles with selective catalytic reduction
Closing the filler neck
"'Turn the Ad Blue cap to the r ight on the filler
tube unti l th e cap cl ic k s into
p lace ¢.&. in
Prepara tion on page 320,
¢ (Din Preparation
on page 320 ..
"' Then press on the left side of the tank door un-
ti l it latches.
After filling
The vehicle must be driven so tha t the system
recognizes t hat the Ad B lue was refilled. This can
t ake severa l m in utes.
"' If there was no Ad Blue left in the tank and a
r ange of O mi (0 km) was shown in the d isplay,
swi tch the ign ition on fo r abo ut 30 seconds be­
f ore star ting the engine .
(D Tips
Ad Blue in the tank can free ze at very low tem­
pera tures. If this happens, the system will
not detect that the AdB lue was refilled and it
w ill contin ue to inform you of the low AdBlue
322
leve l. The message tu rns off as soon as the
tank thaws out again .
Emissions control
systems
Cat alytic converter
Applies to: vehicles with gasoline engines
T he vehicle may only be driven w ith un leaded
gaso line, otherwise the catalytic converter will be
destroyed .
Never drive unti l the tan k is comp lete ly empty .
T he irregu lar supply of fuel that resu lts from that
can cause eng ine misfires. Uncombusted fuel will
enter the exhaust system , which can cause over­
heating and damage to the catalytic converte r.
Di esel particulate filt er
Applies to: vehicles with diesel engines
The diese l particulate filter filters nearly all of
the soot part icles out of the exhaust. The filter
cleans itself automat ica lly under norma l dr iv ing
cond it io ns. If the filter cannot clean itself (for ex­
amp le, because yo u are on ly driving short distan ­
ces), the filter becomes clogged with soot and
the
1111 i ndicato r light for the diese l particulate
filte r tu rns
on ¢ page 33.
_&. WARNING
The tempera ture o f the e xhaust sys tem is
h igh, both when driving and a fter stopping
the engine.
-
-Never tou ch the e xhaus t tail p ipes o nce they
have become hot. This cou ld resu lt in burns.
-D o not p ark your vehicle over flamm able
materials such as grass or leaves because
the hig h temperature of the emissions con­
trol system (catalyt ic converter or d iese l
pa rticu late filter) co uld start a fire.
- Do not apply underbody protectant in the
exhaust system area, beca use this increases
the risk of f ire.

Checking and Filling
_& WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents ,
and certain vehicle components contain or emit chemicals known to the State of Cali­
fornia to cause cancer and birth defects and reproductive harm. In addition, certain flu ­
ids contained in vehicles and certain prod­
ucts of component wear contain or emit
chemicals known to the State of California
to cause cancer and birth defects or other reproductive harm.
- Battery posts, terminals and related acces­
sories contain lead and lead compounds, chemicals known to the State of California
to cause cancer and reproductive harms.
Wash hands after handling.
(D Note
When filling fluids, be sure not to mix the flu­ ids up . Otherwise severe malfunctions and
en­
gine damage will occur.
@ For the sake of the environment
You should regularly check the ground under
your vehicle in order to detect leaks quickly . If
there are visible spots from oil or other fluids,
bring your vehicle to an authorized Audi deal­
er or authorized Audi Service Facility to be
checked.
Opening and closing the hood
The hood is released from ins ide the vehicle.
Fig. 266 Drive r footwell : rele ase le v er
324
Fig. 267 Unlocked hood: lev er
Make sure the wiper arms are not raised up from
the windshield. Otherwise the paint could be
damaged .
Opening the hood
"'With the driver's door open, pull the lever be­
low the instrument panel in the direction of the
arrow
9 fig . 266 .
"' Raise the hood slightly 9 ,&.
"'Press the lever ~ fig. 267 in the direction of the
arrow. This releases the hooks.
"' Open the hood.
Closing the hood
"' Push the hood down until you override the
force of the struts .
"'Let the hood fall lightly into the latch . Do not
press it in.
9 ,& .
_& WARNING
-Never open the hood when there is steam or
coolant escaping from the engine compart­
ment, because there is a risk that you could
be burned. Wai t until no steam or coolan t is
escaping.
- For safety reasons, the hood must always be
closed securely while driving . Because of
this, always check the hood after closing it
to make sure it is latched correctly . The
hood is latched if the front corners cannot
be lifted .
- If you notice that the hood is not latched
while you are driving, stop immediately and
close it, because driving when the hood is
not latched increases the risk of an accident.
,...

Check ing and F illing
I f you must add oi l between oi l changes, use an
oil that matches the Audi oi l quality standard
listed on the st icker. The sticker is located at the
front of the engine
compartment <=> page 325,
fig. 268.
Au di r ec omm end s
ocastrol i/g/g'fE:@t P'r(w.:::-..~J.D,'JAJ..
A udi r ecommends Longli fe high performa nce
e ngin e oil from Audi G enuin e Part s
Using the proper engine oil is important for the
functionality and service life of the eng ine. Your
engine was factory-filled with a h igh-quality oil
which can usually be used throughout the entire
yea r.
0 Note
Your Limited New Vehicle Warranty does not
cover damage o r malfunctions due to failure
to follow recommended maintenance and use
requirements as set fo rth in the Aud i Owner's
Man ual and Warranty
& Maintenance booklet.
- Use only a high qual ity eng ine oi l th at ex-
p ressly complies with the Audi oil q uality
standard specified for your vehicle's engine .
Using any other oil can cause se rious engine
damage .
- Do not mix any lubricants or other additives into the engine oil. Doing so can cause en­
gine damage.
(D Tips
If you need to add oil and there is none availa ­
ble that meets the Audi oi l quality standard
your engine requi res, you may add a total of
no more than 0.5 qt (0.5 l) of a h igh-quality
"synthet ic" o il that meets the following speci­
fications.
- Vehicles with gasoline eng ine: ACEA A3 or
API SM with a viscosity grade of SAE OW-30,
SAE 5W-30 or SAE 5W-40.
- Vehicles w ith diesel eng ine: ACEA C3 or
API CF with a v iscosity grade of SAE OW-30
or SAE 5W-30 .
- For more information about engine oi l that
has been approved for your vehicle, please
contact eithe r your authorized Aud i dealer
or Audi Custome r Relat ions at
326
1 (800) 822-2834 or visit our web site at
www.audi usa .com or www .audicanada .ca.
Engine oil consumption
The engine in your vehicle depends on an ade­
quate amount of oil to lubricate and cool all of
its moving ports.
In order to prov ide effect ive lub ricat ion and cool ­
ing of internal engine components, all internal
combustion engines consume a certain amount
of oil. Oil consumption var ies from engine to en­
gine and may change significantly over the life of
the engine. Typically, engines w ith a specified
break-in period
(see<=> page 80) consume more
o il dur ing the break-in per iod than they consume
after o il consumption has stabi lized .
U nder normal cond itions, the rate of oil con­
sumption depends on the quality and viscos ity of
the oil, the RPM (revolutions per m inute) at
wh ich the engine is operated, the amb ient tem­
perature and road condit ions. Furthe r facto rs a re
t h e amo unt of o il di lution from wate r condensa­
t ion or fue l residue a nd the oxidat ion level of the
oi l. As any engine is subject to wear as mileage
builds up, the oi l consumption may increase ove r
ti me until replacement of worn components may
become necessary.
With a ll these variab les coming into p lay, no
standard rate of oil cons umption can be estab ­
li shed or specified . There is no alternative to reg­
ular and frequent checking of the oil level, see
Note .
If the yellow engine oil leve l warning symbo l El
in the instrument cluster lights up, you should
check the o il level as soon as possible
<=> page 32 7. Top off the o il at your earliest con­
venience
<=> page 32 7.
A WARNING
Before you check anyth ing in the e ngine com­
partment, always read and heed all WARN­
I NGS<=> .&. in Working in the engine compart-
ment on page 323.
1iJ>,

Checking and Filling
Charging the vehicle battery
Fig. 272 Engine co mpa rtment : connec tors for a c harger
and jump start cab le s
Req uirement: only use chargers with a m aximum
c hargi ng vo lta ge of 30 amp s/14.8 Volt s.
The
vehicle battery cables remain connected .
.,. Read the warnings c> .&. in General warnings
about batteries on page 331
and c> ,&. .
.,. Switch off the ignition and all electrical equip ­
ment .
.,. Open the hood 9 page 324 .
.,. Open the red cover on the positive terminal
c>fig. 272 .
.,. Clamp the charger terminal clamps to the jump
s ta rt pin s
according to the instruct ions . (pin
under the red cover = "positive ", p in with hex­
agonal head= "negative ") .
.,. Inse rt the powe r cable for the charg ing device
i nto the socke t and switch the dev ice on .
.,. At the end of the charging process , switch the
charger off and pull the power cab le out of the
socket .
.,. Remove the charger terminal clamps.
.,. Close the red cover on the positive terminal.
.,. Close the hood c> page 324 .
A WARNING
-A highly explosive mixtu re of gases can form
when cha rging batter ies. On ly charge the
vehicle batte ry in well-ven tilated areas.
- A drai ned vehicle battery can freeze at tem­
peratu res a round 32
QF (0 QC). A froze n or
thawed veh icle bat tery must not be charged
and must not be used anymore. The ba ttery
housing can crac k and battery acid can leak
o ut if ice forms, wh ich increases the r isk of
an exp losion and chemical burns. Contact an
332
author ized Audi dealer or authorized A udi
Service Facility for more information.
- Do not connect or disconnect the charging
cable whi le charging because this increases
the risk of an explos ion.
@ Tips
- Only charge the vehicle battery t hrough the
connect ions in the engine compartme nt.
- Read all of the manufacturer's instructions
for the charger before charging the vehicle
battery.
Windshield washer system
Fi g. 2 7 3 Engine compar tm ent: washer flui d res ervoir cap
The windshield washer fluid reservoir¢ contains
t he cleaning solution for the windshield and th e
headlight washer system *
c> page 325, fig. 268 .
The reservoir capaci ty can be found in
c> page 381.
To reduce the risk of lime scale deposits on the
spray no zzles, use clean water with low amounts
of calcium . Always add w indow cleaner to the wa­
ter . When the outside temperatures are cold, an
anti -freezing agent should be added to the water
so that it does not freeze .
(D Note
-The concentration o f ant i-freez ing agent
must be adjusted to the ve hicle operat ing
conditions in the respective climate . A con­
cent ration t hat is too high can lead to vehi­
cl e damage.
- Never add radiator anti-freeze or other addi­
t ives to the washer fluid.

a co .... N ,....
N .... 0 0
3 co
q page 353. In some cases, you must drive for
several minutes after storing the pressures until
the indicator light turns off . If the indicator lig ht
does turn off or turns on aga in after a short peri­
od of time, drive to an authorized Audi dealer or
author ized Audi Service Facility immed iately to
have the ma lfunction corrected .
A WARNING
-If the t ire pressu re indica tor appea rs in the
display, red uce your speed immed iate ly and
avoid any har d st eer ing or braking maneu­
vers. Stop a s soon as possib le and check the
ti res and their press ure.
- T he driver is responsi ble for main taining the
cor rect ti re pressure. You must check the
tire pressure regu larly .
- Under certa in conditions (s uch as a sporty
driving style, winte r cond itio ns or unpaved
roads), the tire pressure monitoring system
indicator may be delayed.
(D Tips
- The t ire press ure monitoring sys tem can al ­
so stop work ing when there is an ESC mal ­
funct ion .
- Usin g snow chains may result in a system
malfunction.
- The t ire press ure moni toring sys tem in yo ur
A udi was ca librated with "A udi Orig inal
Tires"¢
page 341 . Using these ti res is rec­
ommended.
Storing tire pressures
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­ tem.
~ Make s ure before storing that the tire pressures
of a ll fo ur ti res meet the specified values and
are adapted to the load
¢ page 344.
~ Switch the ign ition on.
~ Select in the Infotainment system: I MENUI but­
ton
> Vehicle > Service & checks > Tire pre s­
s ure monitoring > Store tire pres sure > Yes ,
store now .
Wheel s
{!) Tips
Do not store the tire pressures if snow chains
are installed.
353

Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value.
It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The required cleaning and care products can be
obtained from an authorized Audi dealer or au­
thorized Service Facility. Read and follow the in­
structions for use on the packaging .
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health .
- Always store cleaning and care products out
of reach of children to reduce the risk of poi­
soning .
@ For the sake of the environment
- Preferably purchase environmentally-friend­
ly cleaning products.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer that deposits such as insects, bird
droppings, tree sap or road salt remain on the ve­ hicle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
increase the damaging effect .
Before washing, rinse off heavy deposits with
plenty of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a microfiber cloth.
Also, wash the underside of your vehicle once road salt stops being used for the season .
Pressure washers
When washing your veh icle w ith a pressure wash ­
er, always follow the operating instructions pro­
vided with the pressure washer. This is especially
important in regard to the pressure and spraying
distance. Do not aim the spray directly at the
354
seals on the side windows, doors, lids or the sun­
roof* or at tires, rubber hoses, insulating materi­
al, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozzles or high pressure nozzles.
The water temperature must not be above 140 °F
(60 °().
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows and roof* are closed
and the windshield wipers are off . Follow instruc­
tions from the car wash operator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes.
Washing by hand
Clean the vehicle starting from the top and work­
ing down using a soft sponge or cleaning brush.
Use solvent-free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi­
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint .
Apply the product using a microfiber cloth. To
avoid damaging the paint surface, do not use too
much pressure.
Rinse the vehicle thoroughly with water. Then
clean using a neutral shampoo and a soft micro­
fiber cloth .
Rinse the vehicle thoroughly again and let it air
dry. Remove any water residue using a chamois .
A WARNING
-
- Only wash the vehicle when the ignition is
off and follow the instructions from the car

a co .... N ,....
N .... 0 0
3 co
Care and cleaning
Component Situation Solution
T ex til es
Deposits adhering to Vacuum cleaner
art ifici al leat her, the surface
A lcan tara Water-based deposits Absorbent
cloth and mild soap solutiona>
such as coffee, tea,
b lood, etc.
Oil -based deposits Apply a m ild soap solution
a), blot away the dissolved o il or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such
Special stain remover, blot with absorbent material, treat
as ink, nail polish, la- afterward with mild soap solution, if necessary
a)
tex paint, shoe pol-
ish, etc.
Natu ral le ath er Fresh stains Cotton cloth with a mild soap so lution a>
Water-based deposits Fresh stains: absorbent cloth
such as coffee, tea, Dried stains : stain
remover suitable fo r leather
b lood , etc.
Oi l-based deposits Fresh stains: absorbent cloth and stain
remover suitable
such as oil, make-up, for leather
etc. Dried stains : grease dissolving spray
Special deposits such Spot remove r suitab le for leather
as ink, nai l polish, la-
tex paint, shoe pol-
ish, etc.
Care Regularly apply condit ion ing c ream that protects from
lig ht and penet rates into the material. Use specia lly-co l-
ored conditioning cream, if necessary .
Carbon part s Deposits clean the same way as plast ic parts
a) Mi ld soap solution: maximum two tablespoons of neutral soap in 1 q uart (1 liter) of water
.8, WARNING
The windshield may not be trea ted with wa­
ter-repelling windshield coating agents. Un ­
favorable cond itions such as wetness, dark­
ness, or low sun can result in increased glare.
Wiper blade chatter is also possible.
@ Note
- Headlight s/tail li ght s
-Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcohol, because they could cause
cracks to form.
- Whe els
-
- Never use a ny pa int polish or other abra­
sive materials .
- Damage to the protect ive layer on the
rims such as sto ne ch ips or scratches must
be repaired immediately .
-Sen sor s/camera l enses
- Neve r use warm or hot water to remove
snow or ice from the camera lens . This
could cause the lens to crack .
- Neve r use ab rasive cleaning materials or
a lcohol to clean the camera lens . This
could cause scratches and cracks .
-Door window s
-Remove snow and ice on windows and ex-
terior mirrors w ith a plast ic scraper . To
357