2017 YAMAHA YXZ1000R torque

8-18
8
9. Place an oil pan under the engine to col-lect the used engine oil.
10. Remove the engine oil drain bolt and its gasket to drain the oil from the engine.
TIPA “ ” mark is stamped on the crankcase
near the engine oil drain bolt for easy identifi-
cation. 11. Install the engine oil drain bolt, engine oil
tank drain bolt and their new gaskets,
and then tighten the bolts to the specified
torques.
1. Engine oil tank drain bolt
2. Gasket
2
1
1. Engine oil drain bolt
2. Gasket
3. “ ” mark
1 2
3
UB577AE0.book Page 18 Wednesday, June 8, 2016 9:35 AM

8-19
8
12. Add 2.00 L (2.11 US qt, 1.76 Imp.qt) ofthe recommended engine oil to the oil
tank, and then install and tighten the en-
gine oil tank filler cap and the cylinder
head cap.
13. Start the engine, warm it up for several minutes, and then turn it off.
14. Remove the engine oil tank filler cap, and then add sufficient oil of the recommend-
ed type to raise it to the maximum level
mark on the dipstick.
TIPBe sure to wipe off spilled oil on any parts af-
ter the engine and exhaust system have
cooled down. NOTICEECB03020Do not use oils with a diesel specifica-
tion of “CD” or oils of a higher quality
than specified. In addition, do not use
oils labeled “ENERGY CONSERVING II”
or higher.
 Make sure that no foreign material en-
ters the oil tank.
Tightening torques:
Engine oil drain bolt:10 N·m (1.0 kgf·m, 7.2 lb·ft)
Engine oil tank drain bolt: 16 N·m (1.6 kgf·m, 12 lb·ft)
Recommended engine oil: See page 10-1.
Oil quantity: Oil change only:2.50 L (2.64 US qt, 2.20 Imp.qt)
Oil change and filter replacement: 2.70 L (2.85 US qt, 2.38 Imp.qt)
UB577AE0.book Page 19 Wednesday, June 8, 2016 9:35 AM

8-22
8
TIPAn oil filter wrench is available from a Yamaha
dealer. 7. Apply a light coat of clean engine oil to
the O-ring of the new oil filter cartridge.TIPMake sure that the O-ring is properly seated.
8. Install the new oil filter cartridge with anoil filter wrench, and then tighten it to the
specified torque with a torque wrench.
1. Oil filter cartridge
2. Oil filter wrench
2
1
1. O-ringTightening torque:Oil filter cartridge:17 N·m (1.7 kgf·m, 12 lb·ft)
1
UB577AE0.book Page 22 Wednesday, June 8, 2016 9:35 AM

8-23
8
9. Install the drain bolts, and then add thespecified amount of the recommended
engine oil. Check the engine oil level and
the vehicle for oil leakage. Install the en-
gine oil tank cover and panel C.TIPRefer to steps 11–19 of the “To change the
engine oil” section for the oil filling procedure.
10. Slide the front portion of the center bot- tom panel into place as shown, and then
hook the left and right sides of the center
bottom panel into place.
1. Torque wrench
1
1. Center bottom panel
1
UB577AE0.book Page 23 Wednesday, June 8, 2016 9:35 AM

8-24
8
11. Install the center bottom panel bolts, andthen tighten them to the specified torque.1. Center bottom panel
1
1. Bolt A
2. Bolt B
3. Bolt C
1
2
3
UB577AE0.book Page 24 Wednesday, June 8, 2016 9:35 AM

8-25
8
12. Install the rear bottom panel by installingthe bolts, and then tightening them to the
specified torque. 13. Install the side panel bolts, and then tight-
en them to the specified torque.1. Bolt A
2. Bolt B
3. Bolt CTightening torques:Bolt A:7 N·m (0.7 kgf·m, 5.1 lb·ft)
Bolt B: 7 N·m (0.7 kgf·m, 5.1 lb·ft)
Bolt C: 7 N·m (0.7 kgf·m, 5.1 lb·ft)1
3
2
3
1. Rear bottom panel
2. Bolt A
3. Bolt BTightening torques: Bolt A:7 N·m (0.7 kgf·m, 5.1 lb·ft)
Bolt B: 7 N·m (0.7 kgf·m, 5.1 lb·ft)
3
1
2
2
UB577AE0.book Page 25 Wednesday, June 8, 2016 9:35 AM

8-26
8
EBU35104Transmission oilCheck the oil level and change the transmis-
sion oil at the intervals specified in the general
maintenance and lubrication chart.
NOTICEECB02910When checking or changing the transmis-
sion oil, make sure that no foreign material
enters the transmission. If necessary,
clean the filler cap and surrounding area. To check the transmission oil level1. Park the vehicle on a level surface.
2. Remove panel B (page 8-10).
3. Remove the transmission oil filler cap, wipe the dipstick off with a clean rag, in-
sert it back into the transmission case
(without screwing it in), and then remove
it again to check the oil level.
1. Bolt BTightening torque:Bolt B:7 N·m (0.7 kgf·m, 5.1 lb·ft)
1
1
UB577AE0.book Page 26 Wednesday, June 8, 2016 9:35 AM

8-28
8
5. Install the transmission oil drain bolt andnew gasket, and then tighten the bolt to
the specified torque.
6. Check the O-ring for damage, and re- place it if necessary. 7. Refill with the specified amount of the
recommended oil, and then install the
transmission oil filler cap.
NOTICEECB03150Do not use oils with a diesel specifica-
tion of “CD” or oils of a higher quality
than specified. In addition, do not use
oils labeled “ENERGY CONSERVING II”
or higher.
 In order to prevent clutch slippage, do
not mix any chemical additives. TIPBe sure to wipe up any spilled oil.
1. Transmission oil drain bolt
2. GasketTightening torque:
Transmission oil drain bolt:20 N·m (2.0 kgf·m, 14 lb·ft)2
1
Recommended oil:See page 10-1.
Oil quantity: 1.50 L (1.59 US qt, 1.32 Imp.qt)
UB577AE0.book Page 28 Wednesday, June 8, 2016 9:35 AM