2017 YAMAHA YS125 warning

Periodic maintenance an d a djustment
6-26
6
EAU23098
Checkin g an d lu bricatin g the
ca blesThe operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubri-
cated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or re-
place it. WARNING! Dama ge to the
outer housin g of cab les may result
in internal rustin g an d cause inter-
ference with ca ble movement. Re-
place damag ed cab les as soon as
possi ble to prevent unsafe con di-
tions.
[EWA10712] EAU49921
Checkin
g an d lu bricatin g the
throttle grip an d ca bleThe operation of the throttle grip
should be checked before each ride. In
addition, the cable should be lubricat-
ed by a Yamaha dealer at the intervals
specified in the periodic maintenance
chart.
EAU44276
Checkin g an d lu bricatin g the
b rake an d shift pe dalsThe operation of the brake and shift
pedals should be checked before each
ride, and the pedal pivots should be lu-
bricated if necessary.
Brake pe dal
Shift pe dal
Recommen ded lu bricant:
Yamaha cable lubricant or other
suitable cable lubricant
UBT4E0E0.book Page 26 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-28
6
EAU23215
Checkin g an d lu bricatin g the
centerstan d an d si destan dThe operation of the centerstand and
sidestand should be checked before
each ride, and the pivots and metal-to-
metal contact surfaces should be lubri-
cated if necessary.
WARNING
EWA10742
If the centerstan d or si destan d d oes
not move up an d d own smoothly,
have a Yamaha d ealer check or re-
pair it. Otherwise, the centerstan d or
si destan d coul d contact the groun d
an d d istract the operator, resultin g
in a possib le loss of control.
EAUM1653
Lubricatin g the swin garm piv-
otsThe swingarm pivots must be lubricat-
ed by a Yamaha dealer at the intervals
specified in the periodic maintenance
and lubrication chart.
Recommen ded lu bricant:
Lithium-soap-based grease
Recommen ded lu bricant:
Lithium-soap-based grease
UBT4E0E0.book Page 28 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-29
6
EAU23273
Checkin g the front forkThe condition and operation of the
front fork must be checked as follows
at the intervals specified in the periodic
maintenance and lubrication chart.
To check the con dition
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation 1. Place the vehicle on a level surfa- ce and hold it in an upright posi-
tion. WARNING! To avoi d injury,
securely support the vehicle so
there is no dan ger of it fallin g
over.
[EWA10752]
2. While applying the front brake, push down hard on the handle-
bars several times to check if the
front fork compresses and re-
bounds smoothly.
NOTICE
ECA10591
If any d amage is foun d or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.
EAU45512
Checkin g the steerin gWorn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Place the vehicle on the center- stand. WARNING! To avoi d inju-
ry, securely support the vehicle
so there is no dan ger of it fallin g
over.
[EWA10752]
2. Hold the lower ends of the front fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steer-
ing.
UBT4E0E0.book Page 29 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-30
6
EAU23292
Checkin g the wheel bearin gsThe front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer
check the wheel bearings.
EAU2338A
BatteryThe battery is located behind panel B.
(See page 6-8.)
This model is equipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electro-
lyte or to add distilled water. However,
the battery lead connections need to
be checked and, if necessary, tight-
ened.
WARNING
EWA10761
 Electrolyte is poisonous an d
d an gerous since it contains sul-
furic aci d, which causes severe b
urns. Avoi d any contact with
skin, eyes or clothin g an d al-
ways shiel d your eyes when
workin g near b atteries. In case
of contact, ad minister the fol-
lowin g FIRST AID.
EXTERNAL: Flush with plenty of water.
INTERNAL: Drink lar ge quan-
tities of water or milk an d im-
me diately call a physician.
EYES: Flush with water for 15 minutes an d seek prompt
me dical attention.
 Batteries pro duce explosive hy-
d ro gen gas. Therefore, keep
sparks, flames, ci garettes, etc.,
away from the battery an d pro-
vi de sufficient ventilation when
char gin g it in an enclose d
space.
 KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.1. Battery
2. Positive battery lead (red)
3. Negative battery lead (black)
2
1
3
UBT4E0E0.book Page 30 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-32
6
The spare fuse is located on the rear of
the starter relay holder.
To access the spare fuse, remove the
starter relay (together with its holder)
by pulling it out, then turn the starter re-
lay over. If the fuse is blown, replace it as fol-
lows.
1. Turn the key to “ ” and turn off all electrical circuits.
2. Remove the blown fuse, and then install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a hi gher ampera ge
ratin g than recommen ded to
avoi d causin g extensive dam-
a g e to the electrical system an d
possi bly a fire.
[EWA15132]
3. Turn the key to “ ” and turn on
the electrical circuits to check if
the devices operate.
4. If the fuse immediately blows again, have a Yamaha dealer
check the electrical system.
1. Fuse
2. Starter relay holder
1
2
1. Spare fuse
2. Starter relay holder
3. Starter relay
Specified fuse:
15.0 A
1 2
3
UBT4E0E0.book Page 32 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-36
6
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the screw. NOTICE: Do not over-
ti g hten the screw, otherwise the
lens may break.
[ECA11192] EAU78970
Replacin
g the license plate
lig ht bul b1. Remove the license plate light unit
by removing the nuts.
2. Remove the license plate light bulb socket (together with the
bulb) by pulling it out.
3. Remove the burnt-out bulb by pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with the bulb) by pushing it in.
6. Install the license plate light unit by installing the nuts.
EAU24361
Front wheel
EAUW3361
To remove the front wheel
WARNING
EWA10822
To avoi d injury, securely support the
vehicle so there is no dan ger of it
fallin g over.1. Take the vehicle off the center-
stand so that the front wheel is on
the ground, and then put the side-
stand down.
2. Loosen the front wheel axle nut.
1. Turn signal light bulb
1
1. License plate light unit
2. License plate light bulb
3. License plate light bulb socket
4. Nut
1
32
4
4
1. Axle nut
1
UBT4E0E0.book Page 36 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-37
6 3. Place the vehicle on the center-
stand, and then remove the axle
nut.
4. Pull the wheel axle out, and then remove the wheel. NOTICE: Do
not apply the b rake after the
wheel an d b rake disc have b een
remove d, otherwise the brake
pa ds will be forced shut.
[ECA11073]
To install the front wheel
1. Lift the wheel up between the fork legs.TIPMake sure that there is enough space
between the brake pads before insert-
ing the brake disc into the caliper.
2. Insert the wheel axle, and then in-stall the axle nut.
3. Take the vehicle off the center- stand so that the front wheel is on
the ground, and then put the side-
stand down.
4. Tighten the axle nut to the speci- fied torque.
5. Push down hard on the handlebar several times to check for proper
fork operation.
EAU25081
Rear wheel
EAU78751
To remove the rear wheel
WARNING
EWA10822
To avoi d injury, securely support the
vehicle so there is no dan ger of it
fallin g over.1. Take the motorcycle off the cen-
terstand so that the rear wheel is
on the ground, and then put the
sidestand down.
2. Loosen the axle nut.
3. Disconnect the brake torque rod from the brake shoe plate by re-
moving the nut and the bolt.
1. Wheel axle
1
Tightenin g torque:
Axle nut: 59 N·m (5.9 kgf·m, 43 lb·ft)
UBT4E0E0.book Page 37 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-39
6
TIPThe drive chain does not need to be
disassembled in order to remove and
install the wheel.9. Remove the wheel.
To install the rear wheel 1. Install the drive chain onto the rear sprocket.
2. Install the wheel by installing the collars on both sides and installing
the washer and the wheel axle
from the right side.
3. Install the washer and the axle nut.
4. Connect the brake rod to the brake camshaft lever, and then in-
stall the brake pedal free play ad-
justing nut onto the brake rod.
5. Connect the brake torque rod to the brake shoe plate by installing
the bolt and the nut.
6. Adjust the drive chain slack. (See page 6-24.)
7. Take the motorcycle off the cen- terstand so that the rear wheel is
on the ground, and then put the
sidestand down. 8. Adjust the brake pedal free play.
(See page 6-21.)
WARNING
EWA10661
After a djustin g the brake pe dal free
play, check the operation of the
b rake li ght.
EAU25853
Trou bleshootin gAlthough Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
WARNING
EWA15142
When checkin g the fuel system, do
not smoke, an d make sure there are
no open flames or sparks in the ar-
ea, inclu din g pilot li ghts from water
UBT4E0E0.book Page 39 Thursday, November 17, 2016 10:55 AM