2017 YAMAHA YS125 check engine

Periodic maintenance an d a djustment
6-13
6 5. Remove and replace the oil filter
element and O-ring.
6. Install the oil filter element cover by installing the bolts, then tight-
ening them to the specified
torque.
TIPMake sure that the O-ring is properly
seated.7. Install the engine oil drain bolt andits new gasket, and then tighten
the bolt to the specified torque. 8. Refill with the specified amount of
the recommended engine oil.
NOTICE
ECA11621
In or der to prevent clutch slip-
pa ge (since the en gine oil also
lu bricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a hi gh-
er quality than specifie d. In
a ddition, do not use oils la beled
“ENERGY CONSERVING II” or
hi gher.
 Make sure that no forei gn mate-
rial enters the crankcase.
9. Check the O-ring for damage, and replace it if necessary.
10. Install and tighten the engine oil filler cap.NOTICE
ECA10441
After chan gin g the en gine oil, b e
sure to check the oil pressure as de-
scri bed b elow.To check the oil pressure
1. Remove cowling A. (See page 6-8.)
2. Remove the Y.R.C.S. (Yamaha Ram-Air Cooling System) cap.
(See page 6-10.)
1. Oil filter element
2. O-ringTightenin g torque:
Oil filter element cover bolt: 10 N·m (1.0 kgf·m, 7.2 lb·ft)
2 1
Ti
ghtenin g torque:
Engine oil drain bolt:
20 N·m (2.0 kgf·m, 14 lb·ft)
Recommen ded en gine oil:
See page 8-1.
Oil quantity:
Oil change:1.00 L (1.06 US qt, 0.88 Imp.qt)
With oil filter removal:
1.10 L (1.16 US qt, 0.97 Imp.qt)
1. Engine oil filler cap
2. O-ring
21
UBT4E0E0.book Page 13 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-14
6
3. Loosen the bleed bolt, start the
engine and keep it idling until oil
flows out. If no oil comes out after
several minutes, turn the engine
off immediately and consult a
Yamaha dealer for inspection.
4. After checking the oil pressure, tighten the bleed bolt with the
specified torque.
5. Install the Y.R.C.S. (Yamaha Ram- Air Cooling System) cap.
6. Install the cowling. 7. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off
and check for the cause.
8. Turn the engine off, check the oil level and correct it if necessary.
EAUW3321
Cleanin g the air filter element
an d cleanin g the check hoseThe air filter element should be cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
Clean the air filter element more fre-
quently if you are riding in unusually
wet or dusty areas. In addition, the air
filter check hose must be frequently
checked and cleaned if necessary.
To clean the air filter element
1. Remove panel A. (See page 6-8.)
2. Remove the air filter case cover by removing the screws, and then
pull the air filter element out.
1. Bleed boltTightenin g torque:
Bleed bolt: 7 N·m (0.7 kgf·m, 5.1 lb·ft)
1
1. Air filter case cover
2. Screw
2 2
1
UBT4E0E0.book Page 14 Thursday, November 17, 2016 10:55 AM

Periodic maintenance an d a djustment
6-16
6
EAU34302
A djustin g the en gine i dlin g
spee dThe engine idling speed must be
checked and, if necessary, adjusted as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.
The engine should be warm before
making this adjustment.
Check the engine idling speed and, if
necessary, adjust it to specification by
turning the idle adjusting screw. To in-
crease the engine idling speed, turn
the screw in direction (a). To decrease
the engine idling speed, turn the screw
in direction (b).
TIPIf the specified idling speed cannot be
obtained as described above, have a
Yamaha dealer make the adjustment.
EAU21386
Checkin g the throttle grip free
playMeasure the throttle grip free play as
shown.
Periodically check the throttle grip free
play and, if necessary, have a Yamaha
dealer adjust it.
1. Idle adjusting screw
1
(b)
(a)
En gine i dlin g spee d:
1300–1500 r/min
1. Throttle grip free play
Throttle grip free play:
3.0–7.0 mm (0.12–0.28 in)
1
UBT4E0E0.book Page 16 Thursday, November 17, 2016 10:55 AM

Periodic maintenance and adjustment
6-17
6
EAU21402
Valve clearanceThe valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.
EAU69760
TiresTires are the only contact between the
vehicle and the road. Safety in all con-
ditions of riding depends on a relatively
small area of road contact. Therefore, it
is essential to maintain the tires in good
condition at all times and replace them
at the appropriate time with the speci-
fied tires.
Tire air pressure
The tire air pressure should be
checked and, if necessary, adjusted
before each ride.
WARNING
EWA10504
Operation of this vehicle with im-
proper tire pressure may cause se-
vere injury or death from loss of
control. The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).
 The tire air pressure must be
adjusted in accordance with the
riding speed and with the total weight of rider, passenger, car-
go, and accessories approved
for this model.
WARNING
EWA10512
Never overload your vehicle. Opera-
tion of an overloaded vehicle could
cause an accident.Tire air pressure (measured on cold
tires):
1 person:Front:
175 kPa (1.75 kgf/cm², 25 psi)
Rear: 200 kPa (2.00 kgf/cm², 29 psi)
2 persons: Front:175 kPa (1.75 kgf/cm², 25 psi)
Rear: 225 kPa (2.25 kgf/cm², 33 psi)
Maximum load:
Front:175 kPa (1.75 kgf/cm², 25 psi)
Rear:
250 kPa (2.50 kgf/cm², 36 psi)
Maximum load*: 171 kg (377 lb)
* Total weight of rider, passenger, car- go and accessories
UBT4E0E0.book Page 17 Wednesday, December 21, 2016 11:06 AM

Periodic maintenance an d a djustment
6-41
6
EAUT1985
Trou bleshootin g chart
Check the fuel level in
the fuel tank.1. Fuel
There is enough fuel.
There is no fuel.
Check the battery.
Supply fuel.
The engine does not start.
Check the battery.
Operate the electric starter.4. Compression
There is compression.
There is no compression.
The engine does not start.
Have a Yamaha dealer check the vehicle.Have a Yamaha dealer check the vehicle.
Remove the spark plug
and check the electrodes.3. Ignition
Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug. Have a Yamaha dealer check the vehicle.
The engine does not start.
Check the compression.
Operate the electric starter.2. Battery
The engine turns over
quickly.
The engine turns over
slowly.
The battery is good.
DryWet
Operate the electric starter.
Check the battery lead connections,
and have a Yamaha dealer charge
the battery if necessary.
The engine does not start.
Check the ignition.
UBT4E0E0.book Page 41 Thursday, November 17, 2016 10:55 AM

Motorcycle care and stora ge
7-4
7 2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to protect the cylinder, piston rings,
etc. from corrosion.a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several times with the starter. (This will
coat the cylinder wall with oil.)
WARNING! To prevent d am-
a g e or injury from sparkin g,
make sure to groun d the
spark plu g electro des while
turnin g the en gine over.
[EWA10952]
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap.
4. Lubricate all control cables and the pivoting points of all levers and
pedals as well as of the side-
stand/centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully char- ge it. Store it in a cool, dry place
and charge it once a month. Do
not store the battery in an exces-
sively cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the battery, see page
6-30.
TIPMake any necessary repairs before
storing the motorcycle.
UBT4E0E0.book Page 4 Thursday, November 17, 2016 10:55 AM

Consumer information
9-2
9
The model label is affixed to the frame
behind panel A. (See page 6-8.) Re-
cord the information on this label in the
space provided. This information will
be needed when ordering spare parts
from a Yamaha dealer.
EAU69910
Dia
gnostic connectorThe diagnostic connector is located as
shown.
EAU74701
Vehicle data recor din gThis model’s ECU stores certain vehi-
cle data to assist in the diagnosis of
malfunctions and for research and de-
velopment purposes. This data will be
uploaded only when a special Yamaha
diagnostic tool is attached to the vehi-
cle, such as when maintenance checks
or service procedures are performed.
Although the sensors and recorded
data will vary by model, the main data
points are:
 Vehicle status and engine perfor-
mance data
 Fuel-injection and emission-relat-
ed data
Yamaha will not disclose this data to a
third party except:  With the consent of the vehicle
owner
 Where obligated by law
 For use by Yamaha in litigation
 For general Yamaha-conducted
research purposes when the data
is not related to an individual vehi-
cle nor owner
1. Diagnostic connector
1
UBT4E0E0.book Page 2 Thursday, November 17, 2016 10:55 AM

10-1
10
IndexAAir filter element and check hose,
cleaning .............................................. 6-14
Auxiliary light bulb, replacing ................ 6-34BBattery .................................................. 6-30
Brake and clutch levers, checking and lubricating ........................................... 6-27
Brake and shift pedals, checking and
lubricating ........................................... 6-26
Brake fluid, changing ............................ 6-23
Brake fluid level, checking .................... 6-22
Brake lever .............................................. 3-7
Brake lever free play, checking............. 6-20
Brake light switches.............................. 6-21
Brake pads and shoes, checking ......... 6-22
Brake pedal............................................. 3-7
Brake pedal free play, adjusting ........... 6-21
Brake/tail light bulb, replacing .............. 6-35CCables, checking and lubricating ......... 6-26
Care ........................................................ 7-1
Catalytic converters .............................. 3-10
Centerstand and sidestand, checking and lubricating .................................... 6-28
Clutch lever ............................................. 3-6
Clutch lever free play, adjusting ........... 6-19
Cowling and panels, removing and installing................................................ 6-8DData recording, vehicle ........................... 9-2
Diagnostic connector.............................. 9-2
Dimmer switch ........................................ 3-5
Drive chain, cleaning and lubricating .... 6-25 Drive chain slack .................................. 6-24
EEco indicator light................................... 3-2
Engine break-in ...................................... 5-3
Engine idling speed .............................. 6-16
Engine oil and oil filter element ............ 6-11
Engine serial number .............................. 9-1
Engine trouble warning light ................... 3-2FFront fork, checking ............................. 6-29
Fuel ......................................................... 3-8
Fuel consumption, tips for reducing ...... 5-3
Fuel tank cap .......................................... 3-8
Fuse, replacing ..................................... 6-31HHandlebar switches ................................ 3-5
Headlight bulb, replacing ..................... 6-33
High beam indicator light ....................... 3-2
Horn switch ............................................ 3-5IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ............... 3-13
Indicator lights and warning light ........... 3-2LLicense plate light bulb, replacing........ 6-36MMain switch/steering lock....................... 3-1
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission control
system.................................................. 6-3
Matte color, caution ............................... 7-1
Model label ............................................. 9-1
Multi-function meter unit ........................ 3-3
NNeutral indicator light ..............................3-2PParking ....................................................5-4
Part locations ..........................................2-1
Pass switch .............................................3-5SSafety information ...................................1-1
Seat .......................................................3-11
Shifting ....................................................5-2
Shift pedal ...............................................3-6
Shock absorber assemblies, adjusting .............................................3-11
Sidestand ..............................................3-12
Spark plug, checking ............................6-10
Specifications .........................................8-1
Starting the engine ..................................5-1
Start switch .............................................3-6
Steering, checking ................................6-29
Storage ...................................................7-3
Swingarm pivots, lubricating ................6-28TThrottle grip and cable, checking and lubricating ...........................................6-26
Throttle grip free play, checking ...........6-16
Tires ......................................................6-17
Tool kit ....................................................6-2
Troubleshooting ....................................6-39
Troubleshooting chart ...........................6-41
Turn signal indicator light........................3-2
Turn signal light bulb, replacing ............6-35
Turn signal switch ...................................3-5VValve clearance .....................................6-17
UBT4E0E0.book Page 1 Thursday, November 17, 2016 10:55 AM