2017 YAMAHA YFM700R ABS

EBU17421
TABLE OF CONTENTS
LOCATION OF THE WARNING AND
SPECIFICATION LABELS .............................. 1-1
SAFETY INFORMATION ................................ 2-1
DESCRIPTION................................................ 3-1Left view ...................................................... 3-1
Right view.................................................... 3-2
Controls and instruments............................ 3-3
INSTRUMENT AND CONTROL
FUNCTIONS ................................................... 4-1 Main switch ................................................. 4-1
Indicator lights and warning lights .............. 4-2
Self-diagnosis device .................................. 4-3
Handlebar switches .................................... 4-4
Throttle lever ............................................... 4-4
Speed limiter ............................................... 4-5
Clutch lever ................................................. 4-6
Brake lever .................................................. 4-6
Brake pedal ................................................. 4-7
Parking brake lever ..................................... 4-8
Shift pedal ................................................... 4-9
Reverse knob “REV” ................................... 4-9 Fuel tank cap ............................................ 4-10
Fuel ........................................................... 4-10
Seat .......................................................... 4-12
Adjusting the front shock absorber
assemblies (YFM70RSBH) ..................... 4-13
Adjusting the front shock absorber assemblies (YFM70RSSH/
YFM70RSXH) .......................................... 4-15
Adjusting the rear shock absorber assembly (YFM70RSBH) ........................ 4-20
Adjusting the rear shock absorber assembly (YFM70RSSH/
YFM70RSXH) .......................................... 4-22
PRE-OPERATION CHECKS .......................... 5-1 Fuel ............................................................. 5-4
Engine oil .................................................... 5-4
Coolant ....................................................... 5-4
Front and rear brakes ................................. 5-4
Throttle lever ............................................... 5-5
Drive chain .................................................. 5-5
Tires ............................................................ 5-5
Chassis fasteners ....................................... 5-7
Instruments, lights and switches ................ 5-8U2LS62E0.book Page 1 Thursday, February 25, 2016 8:44 AM

3-1
3
EBU17681
DESCRIPTION
EBU17691Left view1. Engine oil tank filler cap
2. Coolant reservoir
3. Fuel tank cap
4. Idle adjusting screw
5. Battery
6. Fuses
7. Rear shock absorber assembly rebound damping force adjusting screw (YFM70RSSH/YFM70RSXH)
8. Rear shock absorber assembly compression damping force adjusting bolt (for fast compression damping)
(YFM70RSSH/YFM70RSXH)
1 2
4
3
658,9
10
11
7
12
9. Rear shock absorber assembly compression damping
force adjusting screw (for slow compression damping)
(YFM70RSSH/YFM70RSXH)
10.Rear shock absorber assembly spring preload adjusting nut
11.Shift pedal
12.Engine oil tank drain bolt
U2LS62E0.book Page 1 Thursday, February 25, 2016 8:44 AM

3-2
3
EBU17701Right view1. Spark arrester
2. Air filter case
3. Rear brake fluid reservoir
4. Crankcase engine oil filler bolt
5. Oil filter element
6. Spark plug
7. Front shock absorber assembly compression damping force adjusting bolt (for fast compression damping)
(YFM70RSSH/YFM70RSXH)
8. Front shock absorber assembly compression damping force adjusting screw (for slow compression damping)
(YFM70RSSH/YFM70RSXH)
9. Front shock absorber assembly spring preload adjusting nut (YFM70RSSH/YFM70RSXH)
10.Front shock absorber assembly spring preload adjusting ring (YFM70RSBH)1
23
456 7,8,9
1312
14
10,11
11.Front shock absorber assembly rebound damping force adjusting screw (YFM70RSSH/YFM70RSXH)
12.Crankcase engine oil drain bolt
13.Brake pedal
14.Rear brake light switch
U2LS62E0.book Page 2 Thursday, February 25, 2016 8:44 AM

4-13
4
EBU30853Adjusting the front shock absorber as-
semblies (YFM70RSBH)The spring preload can be adjusted to suit the rid-
er’s weight and the riding conditions.
WARNING
EWB00401Always adjust the shock absorber assemblies
on the left and right side to the same setting.
Uneven adjustment can cause poor handling
and loss of stability, which could lead to an ac-
cident. Adjust the spring preload as follows.
Turn the spring preload adjusting ring in direction
(a) to increase the spring preload and thereby
harden the suspension, and in direction (b) to de-
crease the spring preload and thereby soften the
suspension.
Align the appropriate notch in the adjusting ring
with the position indicator on the shock absorber.
1. Slot
2. Projection
3. Seat holder
1
2
3
2
U2LS62E0.book Page 13 Thursday, February 25, 2016 8:44 AM

4-14
4
TIPA special wrench can be obtained at a Yamaha
dealer to make this adjustment.
WARNING
EWB00411These shock absorber assemblies contain
highly pressurized nitrogen gas. Read and un-
derstand the following information before han-
dling the shock absorber assemblies.
1. Spring preload adjusting ring
2. Position indicator
(a)(b)
1. Special wrenchSpring preload setting:
Minimum (soft):1
Standard: 2
Maximum (hard): 5
1
U2LS62E0.book Page 14 Thursday, February 25, 2016 8:44 AM

4-15
4

Do not tamper with or attempt to open the
cylinder assemblies.
 Do not subject the shock absorber assem-
blies to an open flame or other high heat
source. This may cause the unit to explode
due to excessive gas pressure.
 Do not deform or damage the cylinders in
any way. Cylinder damage will result in poor
damping performance.
 Do not dispose of a damaged or worn out
shock absorber assembly yourself. Take the
shock absorber assembly to a Yamaha deal-
er for any service.
EBU30981Adjusting the front shock absorber as-
semblies (YFM70RSSH/YFM70RSXH)These shock absorber assemblies are equipped
with a spring preload adjusting nut, a rebound
damping force adjusting screw, with a compres-
sion damping force adjusting bolt (for fast com-
pression damping), and a compression damping
force adjusting screw (for slow compression
damping).
WARNING
EWB02492Suspension components become hot during
operation. Never touch the compression
damping force adjusting bolt and screw, the
rebound damping force adjusting screw or
the oil reservoir with your bare hand or skin
until suspension components have cooled.
 Always adjust the shock absorber assem-
blies on the left and right side to the same
setting. Uneven adjustment can cause poor
handling and loss of stability, which could
lead to an accident. NOTICEECB00091Never turn an adjusting mechanism beyond
the minimum and maximum settings. TIPAlthough the total number of clicks or turns of a
damping force adjusting mechanism may not ex-
actly match the following specifications due to
small differences in production, the actual number
of clicks or turns always represents the entire ad-
justing range. To obtain a precise adjustment, it
U2LS62E0.book Page 15 Thursday, February 25, 2016 8:44 AM

4-19
4
Compression damping force (for slow compres-
sion damping)To increase the compression damping force and
thereby harden the compression damping, turn
the compression damping force adjusting screw
in direction (a). To decrease the compression
damping force and thereby soften the compres-
sion damping, turn the adjusting screw in direction
(b).
WARNING
EWB00411These shock absorber assemblies contain
highly pressurized nitrogen gas. Read and un-
derstand the following information before han-
dling the shock absorber assemblies.

Do not tamper with or attempt to open the
cylinder assemblies.
 Do not subject the shock absorber assem-
blies to an open flame or other high heat
source. This may cause the unit to explode
due to excessive gas pressure.
 Do not deform or damage the cylinders in
any way. Cylinder damage will result in poor
damping performance.
1. Compression damping force adjusting screw (for slow
compression damping)
1 (a)
(b)
1
Compression damping setting (for slow com-
pression damping): Minimum (soft):18 click(s) in direction (b)*
Standard: 9 click(s) in direction (b)*
Maximum (hard): 1 click(s) in direction (b)*
* With the adjusting screw fully turned in di- rection (a)
U2LS62E0.book Page 19 Thursday, February 25, 2016 8:44 AM

4-20
4
Do not dispose of a damaged or worn out
shock absorber assembly yourself. Take the
shock absorber assembly to a Yamaha deal-
er for any service.
EBU19047Adjusting the rear shock absorber as-
sembly (YFM70RSBH)The spring preload can be adjusted to suit the rid-
er’s weight and the riding conditions.NOTICEECB01091Never turn the adjusting mechanism beyond
the minimum and maximum settings. Adjust the spring preload as follows.
1. Loosen the locknut.
2. Turn the spring preload adjusting nut in direc- tion (a) to increase the spring preload and
thereby harden the suspension, and in direc-
tion (b) to decrease the spring preload and
thereby soften the suspension.
TIPA special wrench can be obtained at a Yamaha
dealer to make this adjustment.
 The spring preload setting is determined by
measuring distance A, shown in the illustration.
The shorter distance A is, the higher the spring
preload; the longer distance A is, the lower the
spring preload. With each complete turn of the
adjusting nut, distance A is changed by 1.5 mm
(0.06 in). 1. Spring preload adjusting nut
2. Locknut
3. Special wrench
1
(b)
(a)
2
3
U2LS62E0.book Page 20 Thursday, February 25, 2016 8:44 AM