2017 YAMAHA TRICITY oil change

Instrument and control functions
3-5
3
EAU74444
Multi-function meter unit
WARNING
EWA12423
Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit. Changing
settings while riding can distract the
operator and increase the risk of an
accident.
The multi-function meter unit is
equipped with the following:
za speedometer
za fuel meter
za clock
zan outside air temperature display
za multi-function display
zan oil change indicator
za V-belt replacement indicator
TIP


tons.
Speedometer
The speedometer shows the vehicle’s
traveling speed.
Fuel meter
The fuel meter indicates the amount of
fuel in the fuel tank. The display seg-
ments of the fuel meter disappear from
“F” (full) towards “E” (empty) as the fuel
level decreases. When the last seg-
ment of the fuel meter and the fuel level
warning indicator “ ” start flashing,
refuel as soon as possible. When the
key is first turned to “ON”, all the dis-
1. Clock
2. “SELECT” button
3. Fuel level warning indicator “ ”
4. Fuel meter
5. Speedometer
6. “RESET” button
7. Outside air temperature display
8. Multi-function display
9. Oil change indicator “OIL CHANGE”
10.V-belt replacement indicator “V-BELT”
12345 6
9 107
8
1. Speedometer
1. Fuel level warning indicator Ž
2. Fuel meter
1
1
2
UBR7E0E0.book Page 5 Tuesday, October 25, 2016 2:44 PM

Instrument and control functions
3-7
3 Multi-function display
Under normal conditions, the multi-
function display can be set to display
the following.
zodometer “ODO”
ztripmeters “TRIP 1” or “TRIP 2”
zoil change tripmeter “OIL TRIP”
zV-belt replacement tripmeter
“BELT TRIP”
Push the “SELECT” button to switch
the display between the odometer ,
tripmeters 1 and 2, the oil change trip-
meter and the V-belt replacement trip-
meter in the following order:
ODO → TRIP 1 → TRIP 2 → OIL TRIP
→ BELT TRIP → ODO
To reset tripmeter 1 or 2, select it by
pushing the “SELECT” button, and
then push the “RESET” button for one
second.
TIP
zThe odometer will lock at 999999.
zTripmeters 1 and 2 will reset and
continue counting after 9999.9 is
reached.
Fuel reserve tripmeter
When approximately 1.6 L (0.42 US
gal, 0.35 Imp.gal) of fuel remains in the
fuel tank, the last segment of the fuel
meter and the fuel level warning indica-
tor will start flashing. The display will
automatically change to the fuel re-
serve tripmeter and start counting the
distance traveled from that point. In
this case, push the “SELECT” button
to switch the display in the following
order:
F → TRIP 1 → TRIP 2 → OIL TRIP →
BELT TRIP → ODO → F
To temporarily turn off the fuel reserve
tripmeter, select it by pushing the “SE-
LECT” button, and then push the “RE-
SET” button for one second. To turn
the fuel reserve tripmeter back on, turn
the key to “OFF” and then to “ON”. The
fuel reserve tripmeter will be displayed
again after one minute.
The fuel reserve tripmeter will reset au-
tomatically and disappear after refuel-
ing and traveling 5 km (3 mi).
1. Multi-function display
1
1. Fuel reserve tripmeter
1
UBR7E0E0.book Page 7 Tuesday, October 25, 2016 2:44 PM

Instrument and control functions
3-8
3Oil change tripmeter “OIL TRIP”
The oil change tripmeter shows the
distance traveled since the oil was last
changed.
The oil change indicator “OIL
CHANGE” will come on at the initial
1000 km (600 mi), then at 4000 km
(2500 mi), and then every 4000 km
(2500 mi) thereafter to indicate that the
engine oil should be changed.
After changing the engine oil, reset the
oil change indicator and the oil change
tripmeter. To reset them both, select
the oil change tripmeter, and then push
the “RESET” button for one second.
While “OIL CHANGE” is flashing, push
the “RESET” button for three to four
seconds. The oil change tripmeter will
be reset and the oil change indicator
will turn off.
TIP
If the engine oil is changed before the
oil change indicator comes on (i.e., be-
fore the periodic oil change interval has
been reached), the oil change tripmeter
must be reset for the oil change indica-
tor to come on at the correct time.
V-belt replacement tripmeter “BELT
TRIP”
The V-belt replacement tripmeter
shows the distance traveled since the
V-belt was last replaced.
The V-belt replacement indicator “V-
BELT” will come on every 20000 km
(12500 mi) to indicate that the V-belt
should be replaced.
If the V-belt replacement indicator has
come on, after replacing the V-belt, re-
set the V-belt replacement indicator
and the V-belt replacement tripmeter.
To reset them both, select the V-belt
replacement tripmeter, and then push
the “RESET” button for one second.
While “V-BELT” is flashing, push the
“RESET” button for three to four sec-
onds. The V-belt replacement tripme-
ter will be reset and the V-belt
replacement indicator will turn off.
TIP
If the V-belt is replaced before the V-
belt replacement indicator comes on
(i.e., before the periodic V-belt replace-
ment interval has been reached), the V-
belt replacement tripmeter must be re-
set for the V-belt replacement indicator
to come on at the correct time.
1.
2. Oil change tripmeter
12
1.
2. V-belt replacement tripmeter
12
UBR7E0E0.book Page 8 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-5
6
12*Steering system• Check bearing play and steer-
ing for roughness.
• Check steering tie rod, and re-
place if necessary.√√√√√
• Lubricate with lithium-soap-
based grease.Every 24000 km (14000 mi)
13*Leaning system• Check bearing for looseness or
damage.√√√√√
14*Chassis fasteners• Make sure that all nuts, bolts
and screws are properly tight-
ened.√√√√√
15Front and rear
brake lever pivot
shaft• Lubricate with silicone grease.√√√√√
16*Unified brake sys-
tem• Lubricate link pivots and mov-
ing parts with silicone grease.
• Lubricate cable end with lithi-
um-soap-based grease.√√√√
17Sidestand, center-
stand• Check operation.
• Lubricate with lithium-soap-
based grease.√√√√√
18*Sidestand switch• Check operation and replace if
necessary.√√√√√√
19*Front fork• Check operation and for oil
leakage.
• Replace if necessary.√√√√
20*Shock absorber
assemblies• Check operation and for oil
leakage.
• Replace if necessary.√√√√
21 Engine oil• Change (warm engine before
draining).
• Check oil level and vehicle for
oil leakage.√√√√√√
22
*Engine oil strainer• Clean.√√√
23*Cooling system• Check coolant level and vehicle
for coolant leakage.√√√√√
• Change. Every 3 years NO. ITEM
X 1000 km CHECK OR
MAINTENANCE JOB
X 1000 miODOMETER
READING
ANNUAL CHECK
1481216
0.6 2.4 4.8 7.2 9.6
UBR7E0E0.book Page 5 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-6
6
EAU72780
TIP
zEngine air filter and V-belt air filters
• This model’s engine air filter is equipped with a disposable oil-coated pa-
per element, which must not be cleaned with compressed air to avoid
damaging it.
• The engine air filter element needs to be replaced and the V-belt air filter
elements need to be serviced more frequently when riding in unusually wet
or dusty areas.
zHydraulic brake service
• After disassembling the brake master cylinders and calipers, always
change the fluid. Regularly check the brake fluid levels and fill the reser-
voirs as required.
• Every two years replace the internal components of the brake master cyl-
inders and calipers, and change the brake fluid.
• Replace the brake hoses every four years and if cracked or damaged.
24*Final transmission
oil• Check vehicle for oil leakage.√√√√√
• Change.√Every 12000 km (7200 mi)
25*V-belt• Replace. Every 20000 km (12000 mi)
26*Front and rear
brake switches• Check operation.√√√√√√
27*Moving parts and
cables• Lubricate.√√√√√
28*Throttle grip hous-
ing and cable• Check operation and free play.
• Adjust the throttle cable free
play if necessary.
• Lubricate the throttle grip hous-
ing and cable.√√√√√
29*Lights, signals and
switches• Check operation.
• Adjust headlight beam.√√√√√√ NO. ITEM
X 1000 km CHECK OR
MAINTENANCE JOB
X 1000 mi
ODOMETER
READING
ANNUAL CHECK
1481216
0.62.44.87.29.6
UBR7E0E0.book Page 6 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-9
6To install the spark plug
1. Clean the surface of the spark
plug gasket and its mating sur-
face, and then wipe off any grime
from the spark plug threads.
2. Install the spark plug with the
spark plug wrench, and then tight-
en it to the specified torque.
TIP
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is 1/4…
1/2 turn past finger tight. However, the
spark plug should be tightened to the
specified torque as soon as possible.
3. Install the spark plug cap.
4. Install the panel.
EAU61003
Engine oil and oil strainer
The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil strainer
cleaned at the intervals specified in the
periodic maintenance and lubrication
chart.
To check the engine oil level
1. Place the vehicle on the center-
stand. A slight tilt to the side can
result in a false reading.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Wait a few minutes until the oil set-
tles, remove the engine oil filler
cap, wipe the engine oil dipstick
clean, insert it back into the oil filler
hole (without screwing it in), and
then remove it again to check the
oil level. WARNING! The muffler
and muffler protector become
very hot during use. To avoid
possible burns, let the muffler
and protector cool before re-
moving the oil filler cap.
[EWA17810]
TIP
The engine oil should be between the
tip of the dipstick and the maximum
level mark.
Tightening torque:
Spark plug:
13 N·m (1.3 kgf·m, 9.4 lb·ft)
UBR7E0E0.book Page 9 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-10
6 4. If the engine oil is not between the
tip of the dipstick and the maxi-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Check the O-ring for damage, and
replace it if necessary.
6. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.
To change the engine oil and clean
the oil strainer
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil filler cap
and engine oil drain bolts A and B
to drain the oil from the crankcase.
NOTICE: When removing the
engine oil drain bolt B, the O-
ring, compression spring, and
oil strainer will fall out. Take
care not to lose these parts.
[ECAT1022]
4. Clean the engine oil strainer with
solvent, and then check it for dam-
age and replace it if necessary.
5. Install the engine oil strainer, com-
pression spring, new O-ring and
engine oil drain bolt B.
TIP
Make sure that the O-ring is properly
seated.
6. Install engine oil drain bolt A and
its new gasket, and then tighten
both drain bolts to their specified
torques.
7. Refill with the specified amount of
the recommended engine oil.
1. Engine oil filler cap
2. O-ring
3. Engine oil dipstick
4. Maximum level mark
5. Tip of the engine oil dipstick
1
3
2
4
5
1. Engine oil drain bolt A
2. Gasket
3. Oil strainer
4. Compression spring
5. O-ring
6. Engine oil drain bolt B
Tightening torque:
Engine oil drain bolt A:
20 N·m (2.0 kgf·m, 14 lb·ft)
Engine oil drain bolt B:
32 N·m (3.2 kgf·m, 23 lb·ft)
Recommended engine oil:
See page 8-1.
Oil quantity:
0.90 L (0.95 US qt, 0.79 Imp.qt)
1
3
4
5
6
2
UBR7E0E0.book Page 10 Tuesday, October 25, 2016 2:44 PM

Periodic maintenance and adjustment
6-11
6
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust sys-
tem have cooled down.
NOTICE
ECA11621
zIn order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
zMake sure that no foreign mate-
rial enters the crankcase.
8. Check the O-ring for damage, and
replace it if necessary.
9. Install and tighten the engine oil
filler cap.
10. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off
and check for the cause.
11. Turn the engine off, and then
check the oil level and correct it if
necessary.
12. Reset the oil change tripmeter and
oil change indicator “OIL
CHANGE”. (See page 3-7 for reset
procedures.)
EAU60660
Final transmission oil
The final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
vehicle. In addition, the final transmis-
sion oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Start the engine, warm up the final
transmission oil by riding the vehi-
cle for several minutes, and then
stop the engine.
2. Place the vehicle on the center-
stand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
4. Remove the final transmission oil
filler cap and its O-ring from the fi-
nal transmission case.
5. Remove the final transmission oil
drain bolt and its gasket to drain
the oil from the final transmission
case.
1. Final transmission oil filler cap
2. O-ring
1
2
UBR7E0E0.book Page 11 Tuesday, October 25, 2016 2:44 PM