2017 YAMAHA PW50 tires

Periodic maintenance an d a djustment
7-16
7
which may result in
damag e to
the motorcycle an d injury to the
ri der.
EAU40782
Panel wheels
WARNING
EWA10611
The wheels on this mod el are not
d esi gne d for use with tu beless tires.
Do not attempt to use tu beless tires
on this mo del.
To maximize the performance, durabil-
ity, and safe operation of your motor-
cycle, note the following points
regarding the specified wheels.
 The wheel rims should be
checked for cracks, bends, warp-
age or damage before each ride. If
any damage is found, have a
Yamaha dealer replace the wheel. Do not attempt even the smallest
repair to the wheel. A deformed or
cracked wheel must be replaced.
 The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.
U2SA83E0.book Page 16 Monday, July 11, 2016 2:35 PM

Motorcycle care and stora ge
8-2
8
structed
. Also, thorou ghly rinse
the area off with water, immed i-
ately dry it, an d then apply a cor-
rosion protection spray.
 Improper cleanin g can damag e
plastic parts (such as cowlin gs,
panels, etc.) an d the mufflers.
Use only a soft, clean cloth or
spon ge with water to clean
plastic. However, if the plastic
parts cannot be thorou ghly
cleaned with water, dilute d mil d
d eter gent with water may b e
use d. Be sure to rinse off any
d eter gent resi due using plenty
of water, as it is harmful to plas-
tic parts.
 Do not use any harsh chemical
prod ucts on plastic parts. Be
sure to avoi d usin g cloths or
spon ges which have b een in
contact with stron g or a brasive
cleanin g prod ucts, solvent or
thinner, fuel ( gasoline), rust re-
movers or inhi bitors, brake flui d,
antifreeze or electrolyte.
 Do not use hi
gh-
pressure wash-
ers or steam-jet cleaners since
they cause water seepag e and
d eterioration in the followin g ar-
eas: seals (of wheel an d swin g-
arm bearin gs, fork an d b rakes),
electric components (couplers,
connectors, an d switches),
b reather hoses an d vents.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain or near the sea
Since sea salt is extremely corrosive,
carry out the following steps after each
ride in the rain or near the sea.
1. Clean the motorcycle with cold water and a mild detergent, after
the engine has cooled down.
NOTICE: Do not use warm wa-
ter since it increases the corro-
sive action of the salt.
[ECA10792]
2. Apply a corrosion protection spray on all metal, including chrome-
and nickel-plated, surfaces to pre-
vent corrosion.
After cleanin g
1. Dry the motorcycle with a chamois or an absorbing cloth.
2. Use a chrome polish to shine chrome, aluminum and stainless-
steel parts.
3. To prevent corrosion, it is recom- mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
4. Use spray oil as a universal clean- er to remove any remaining dirt.
5. Touch up minor paint damage caused by stones, etc.
6. Wax all painted surfaces.
7. Let the motorcycle dry completely before storing or covering it.
WARNING
EWA14502
Contaminants on the b rakes or tires
can cause loss of control.
U2SA83E0.book Page 2 Monday, July 11, 2016 2:35 PM

Motorcycle care and stora ge
8-3
8 
Make sure that there is no oil or
wax on the tires.
 If necessary, wash the tires with
warm water and a mild d eter-
g ent. Before ri din g at hi gher
speed s, test the motorcycle’s
b rakin g performance an d cor-
nerin g b ehavior.
NOTICE
ECA10801
 Apply spray oil an d wax spar-
in gly an d make sure to wipe off
any excess.
 Never apply oil or wax to any
rubber an d plastic parts, but
treat them with a suita ble care
prod uct.
 Avoi d usin g a brasive polishin g
compoun ds as they will wear
away the paint.
TIP
Consult a Yamaha dealer for advice on
what products to use.
EAU40646
Stora ge
Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the mo-
torcycle.
NOTICE
ECA10811
 Storin g the motorcycle in a
poorly ventilated room or cover-
in g it with a tarp, while it is still
wet, will allow water an d humi d-
ity to seep in an d cause rust.
 To prevent corrosion, avoi d
d amp cellars, sta bles ( because
of the presence of ammonia)
an d areas where stron g chemi-
cals are store d.
Lon g-term
Before storing your motorcycle for sev-
eral months: 1. Follow all the instructions in the “Care” section of this chapter.
2. For motorcycles equipped with a fuel cock that has an “S” (stop)
position: Turn the fuel cock lever
to “S”.
3. Drain the carburetor float chamber by loosening the drain bolt; this
will prevent fuel deposits from
building up. Pour the drained fuel
into the fuel tank.
4. Fill up the fuel tank and add fuel stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
U2SA83E0.book Page 3 Monday, July 11, 2016 2:35 PM

Motorcycle care and stora ge
8-4
8
5. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING! To
prevent damag e or injury
from sparkin g, make sure to
g roun d the spark plu g elec-
tro des while turnin g the en-
g ine over. [EWA10952]
6. Lubricate all control cables and
the pivoting points of all levers as
well as of the centerstand.
7. Check and, if necessary, correct the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
8. Cover the muffler outlet with a plastic bag to prevent moisture
from entering it.
TIP
Make any necessary repairs before
storing the motorcycle.
U2SA83E0.book Page 4 Monday, July 11, 2016 2:35 PM

Specifications
9-2
9
Spark plug(s):
Manufacturer/model:
NGK/BP4HS (PW50_ZAF)
NGK/BPR4HS
(PW50_AUT/BEL/CHE/CYP/CZE/DEU/DN
K/ESP/FIN/FRA/GBR/GRC/IRL/ITA/NLD/
NOR/POL/PRT/SVK/SVN/SWE/TUR,
PW50H, PW50H2)
Manufacturer/model: DENSO/W14FP-L (PW50_ZAF)
Spark plug gap: 0.6–0.7 mm (0.024–0.028 in)
Clutch:
Clutch type:
Wet, centrifugal, shoe
Drivetrain:
Primary reduction ratio:1.909 (63/33)
Final drive:
Shaft
Secondary reduction ratio: 6.218 (19/15 x 54/11)
Chassis:
Frame type:
Backbone
Caster angle: 25.5 °
Trail: 50 mm (2.0 in)
Front tire:
Type:With tube
Size: 2.50-10 4PR
Manufacturer/model:
BRIDGESTONE/M29
Manufacturer/model: IRC/Z MARK II (PW50_ZAF, PW50H,
PW50H2)
Speed rating: 100 km/h (62 mph)
Rear tire:
Type:
With tube
Size: 2.50-10 4PR
Manufacturer/model: BRIDGESTONE/M29 Manufacturer/model:
IRC/Z MARK II (PW50_ZAF, PW50H,
PW50H2)
Speed rating: 100 km/h (62 mph)
Tire air pressure (measure d on col d
tires):
Front:
100 kPa (1.00 kgf/cm², 15 psi)
Rear: 100 kPa (1.00 kgf/cm², 15 psi)
Front wheel:
Wheel type: Panel wheel
Rim size: 10 x 1.50
Rear wheel:
Wheel type:
Panel wheel
Rim size: 10 x 1.50
Front brake:
Type:
Mechanical leading trailing drum brake
Rear brake:
Type:
Mechanical leading trailing drum brake
Front suspension:
Type:Telescopic fork
Spring: Coil spring
Shock absorber:
Hydraulic damper
Wheel travel: 60 mm (2.4 in)
Rear suspension:
Type:
Unit swing
Spring: Coil spring
Shock absorber: Hydraulic damper
Wheel travel:
50 mm (2.0 in)
Electrical system:
Ignition system:CDI
U2SA83E0.book Page 2 Monday, July 11, 2016 2:35 PM

11-1
11
Index
A
Acceleration and deceleration................ 6-3
Air filter element, cleaning .................... 7-10
Autolube pump, adjusting .................... 7-20
B
Brake lever, front .................................... 4-2
Brake lever, rear ..................................... 4-3
Brake levers, lubricating ....................... 7-20
Brake shoes, checking ......................... 7-18
Braking ................................................... 6-3
C
Cable lock (for Europe)........................... 4-9
Cables, checking and lubricating ......... 7-19
Carburetor, adjusting ........................... 7-12
Care ........................................................ 8-1
Centerstand, checking and
lubricating .......................................... 7-21
E
Engine break-in ...................................... 6-4
Engine idling speed .............................. 7-13
Engine oil ................................................ 4-6
Engine serial number............................ 10-1
Engine, starting a warm ......................... 6-2
Engine stop switch ................................. 4-1
F
Front and rear brake lever free play, adjusting ............................................ 7-17
Front fork, checking ............................. 7-21
Fuel......................................................... 4-4
Fuel cock ................................................ 4-7
Fuel tank breather hose ......................... 4-6
Fuel tank cap.......................................... 4-3
H
Handlebar switch ................................... 4-1
I
Identification numbers.......................... 10-1
K
Kickstarter .............................................. 4-8
L
Labels, location ...................................... 1-1
M
Maintenance and lubrication, periodic ... 7-4
Maintenance, emission control system.................................................. 7-3
Matte color, caution ............................... 8-1
Middle and final gear cases ................. 7-10
P
Parking ................................................... 6-4
Part locations ......................................... 3-1
Power reduction plate, removing ........... 7-7
S
Safety information................................... 2-1
Seat......................................................... 4-8
Spark arrester, cleaning ........................ 7-11
Spark plug, checking .............................. 7-6
Specifications ......................................... 9-1
Speed limiter and power reduction
plate ...................................................... 4-1
Starter (choke) lever ................................ 4-7
Starting and warming up a cold
engine ................................................... 6-1
Starting off .............................................. 6-2
Steering, checking ................................ 7-22
Storage ................................................... 8-3
T
Throttle grip and cable, checking and lubricating ........................................... 7-19
Throttle grip free play, checking ........... 7-14
Tires ...................................................... 7-14
Tool kit .................................................... 7-2
Transmission oil ...................................... 7-8
Troubleshooting .................................... 7-27
Troubleshooting chart........................... 7-28
V
Vehicle Emission Control Information label (For Canada) .............................. 10-1
Vehicle identification number ............... 10-1
W
Wheel bearings, checking..................... 7-22
Wheel (front).......................................... 7-23
Wheel (rear) ........................................... 7-24
Wheels .................................................. 7-16
U2SA83E0.book Page 1 Monday, July 11, 2016 2:35 PM