2017 YAMAHA FX HO cooling

Table of contents
General and important labels ........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number............................................ 1
Craft Identification Number (CIN) ....... 1
Engine serial number.......................... 1
Manufactured date label .................... 2
Model information ........................... 2
Builder’s plate .................................... 2
Important labels .............................. 4
Warning labels.................................... 5
Other labels ........................................ 8
Safety information ........................... 10
Limitations on who may operate
the watercraft ............................. 10
Cruising limitations ........................ 11
Operation requirements ................ 12
Recommended equipment ........... 14
Hazard information........................ 15
Watercraft characteristics ............. 15
Wakeboarding and water-skiing ... 17
Safe boating rules ......................... 18
Enjoy your watercraft
responsibly ................................. 19
Description....................................... 20
Watercraft glossary ....................... 20
Location of main components ...... 21
Control function operation ............. 25
Watercraft control functions ......... 25
Remote control transmitter .............. 25
Yamaha Security System ................. 26
Engine stop switch .......................... 27
Engine shut-off switch .................... 27
Start switch ..................................... 27
Throttle lever .................................... 28
RiDE lever ......................................... 28
Steering system ............................... 28
Adjustable tilt steering system ......... 29
Cooling water pilot outlet ................. 30
Water separator................................ 30
Watercraft operation ...................... 31
Watercraft operation functions ..... 31
Shift system...................................... 31
Electric trim system .......................... 33
Watercraft operation modes ......... 35
Low RPM Mode ............................... 35
No-wake mode ................................. 36
Cruise assist ..................................... 37
Instrument operation ...................... 39
Multifunction information center ... 39
Analog speedometer/tachometer..... 39
Information display ........................... 40
Multifunction display ........................ 44
Equipment operation ...................... 48
Equipment..................................... 48
Seats ................................................ 48
Handgrip........................................... 49
Reboarding grip................................ 49
Reboarding step ............................... 49
Bow eye............................................ 50
Stern eyes ........................................ 50
Cleat ................................................. 50
Pull-up cleats (FX Cruiser HO).......... 51
Storage compartments .................... 51
Fire extinguisher holder and cover ... 56
Operation and handling
requirements ................................... 57
Fuel requirements ......................... 57
Fuel................................................... 57
Engine oil requirements ................ 59
Engine oil .......................................... 59
Draining the bilge water ................ 61
Draining the bilge water on land....... 61
Draining the bilge water on water .... 61
UF2T77E0.book Page 1 Monday, July 11, 2016 9:31 AM

Table of contents
Transporting on a trailer ................ 62
First-time operation ........................ 63
Engine break-in ............................. 63
Pre-operation checks ..................... 64
Pre-operation checklist .................... 64
Pre-operation check points........... 66
Pre-launch checks ........................... 66
Post-launch checks ......................... 72
Operation ......................................... 75
Operating your watercraft ............. 75
Getting to know your watercraft ...... 75
Learning to operate your
watercraft ...................................... 75
Riding position ................................. 76
Launching the watercraft ................. 76
Starting the engine on water ............ 76
Stopping the engine ......................... 77
Leaving the watercraft...................... 77
Operating the watercraft .................. 77
Turning the watercraft ...................... 78
Stopping the watercraft ................... 79
Operating the watercraft in reverse
or neutral....................................... 80
Boarding the watercraft ................... 81
Starting off........................................ 83
Capsized watercraft ......................... 84
Beaching and docking the
watercraft ...................................... 85
Operating in weeded areas .............. 85
After removing the watercraft from
the water ....................................... 86
Care and storage............................. 87
Post-operation care ...................... 87
Flushing the cooling water
passages....................................... 87
Cleaning the watercraft .................... 88
Battery care ...................................... 88
Long-term storage ........................ 91
Cleaning ........................................... 91
Lubrication ....................................... 91Rustproofing ..................................... 91
Maintenance .................................... 92
Maintenance ................................. 92
Tool kit.............................................. 92
Removing and installing the engine
cover ............................................. 92
Periodic maintenance chart ............. 94
Engine oil and oil filter ...................... 96
Specifications .................................. 97
Specifications ............................... 97
Trouble recovery ............................. 98
Troubleshooting ............................ 98
Troubleshooting chart ...................... 98
Emergency procedures .............. 101
Cleaning the jet intake and
impeller ....................................... 101
Raising the reverse gate................. 102
Jumping the battery ....................... 102
Replacing the fuses ........................ 103
Towing the watercraft..................... 105
Submerged watercraft ................... 105
Index............................................... 107
UF2T77E0.book Page 2 Monday, July 11, 2016 9:31 AM

Description
21
EJU31012
Location of main components
Exterior
7
8
9
10
11
2
34561
1Fuel filler cap (page 57)
2Hood
3Handlebar
4Rear seat (page 48)
5Front seat (page 48)
6Footwell
7Bow eye (page 50)
8Hull
9Cooling water pilot outlet (page 30)
10Pull-up cleat (FX Cruiser HO) (page 51)
11Gunwale
UF2T77E0.book Page 21 Monday, July 11, 2016 9:31 AM

Control function operation
30
(2) Make sure that the tilt lever returns to its
original position and that the handlebars
are securely locked in place.
EJU35975Cooling water pilot outlet
When the engine is running, some of the
cooling water that is circulated in the engine
is discharged from the cooling water pilot
outlet.
There is a cooling water pilot outlet on the
port (left) side of the watercraft. To check for
proper operation of the cooling system, make
sure that water is being discharged from the
cooling water pilot outlet. If water is not being
discharged from the outlet, stop the engine
and check the jet intake for clogging. (See
page 101 for information on the jet intake.)
TIP:
It will take about 60 seconds for the water
to reach the outlet after the engine is start-
ed.
Water discharge may not be constant
when the engine is running at idling speed.
If this occurs, apply a little throttle to make
sure that water discharges properly.
EJU40323Water separator
The water separator prevents water from en-
tering the fuel tank by collecting any water
that has entered the fuel tank breather hose if
the watercraft was capsized.
If water has collected in the water separator,
drain it by loosening the drain screw.
To drain water from the water separator:
(1) Place a drain pan or dry cloth under the
water separator.
(2) Gradually loosen the drain screw to drain
the water. Catch the draining water in the
drain pan or soak it up with the dry cloth
so that it does not spill into the engine
compartment. If any water spills into the
watercraft, be sure to wipe it up with a
dry cloth.
(3) Securely tighten the drain screw until it
stops.1Cooling water pilot outlet
1
1Water separator
2Drain screw
2
1
UF2T77E0.book Page 30 Monday, July 11, 2016 9:31 AM

Instrument operation
44
ously. At the same time, the engine speed is
limited.
If the engine overheat warning is activated,
immediately reduce the engine speed, return
to shore, and then make sure that water is
being discharged from the cooling water pilot
outlet while the engine is running. If there is
no discharge of water, stop the engine, and
then check the jet intake for clogging. (See
page 101 for information on the jet intake.)
NOTICE: If you cannot locate and correct
the cause of the overheating, consult a
Yamaha dealer. Continuing to operate at
higher speeds could result in severe en-
gine damage.
[ECJ00042]
TIP:
Push any of the operation buttons for the
multifunction information center to stop the
buzzer.
EJU42281Check engine warning
If a sensor malfunction or a short circuit is de-
tected, the check engine warning indicator
and the “WARNING” indicator light blink, and
the buzzer sounds intermittently.
If the check engine warning is activated, im-
mediately reduce the engine speed, return to
shore, and have a Yamaha dealer check the
engine.
TIP:
Push any of the operation buttons for the
multifunction information center to stop the
buzzer.
EJU43170Multifunction display
The multifunction display shows various wa-
tercraft and environmental information, such
UF2T77E0.book Page 44 Monday, July 11, 2016 9:31 AM

Pre-operation checks
65
TIP:
To ensure safety and reliability, pre-operation checks should be made each time the water-
craft is used.
Jet thrust nozzle and re-
verse gate Check the jet thrust nozzle and reverse gate for
damage.71
Stern drain plugsCheck the stern drain plugs for damage and foreign
material and check that they are securely installed.71
HoodCheck that the hood is securely closed. 72
Front and rear seatsCheck that the seats are securely installed. 48
POST-LAUNCH CHECKS
Cooling water pilot outletCheck that water is discharged from the cooling
water pilot outlet while the engine is running.72
Multifunction information
centerCheck the multifunction information center for prop-
er operation.72
Shift systemCheck the shift system for proper operation. 73
Trim indicatorCheck the trim indicator for proper operation. 73
Engine idling speedCheck the engine idling speed. 74 ITEM ROUTINE PAGE
UF2T77E0.book Page 65 Monday, July 11, 2016 9:31 AM

Pre-operation checks
72
flood the engine compartment and cause
the watercraft to submerge.
[ECJ00363]
Securely install the stern drain plugs by tight-
ening them until they stop.
EJU41441Hood check
Push down on the rear of the hood and make
sure that it is securely closed.
EJU40146Post-launch checks
Perform the post-launch checks in the pre-
operation checklist while the watercraft is in
the water and the engine is running.
To perform the post-launch checks:
(1) Launch the watercraft. (See page 76 for
information on launching the watercraft.)
(2) Perform the checks and make sure that
there are no malfunctioning items or oth-
er problems.
EJU40553Cooling water pilot outlet check
Make sure that water is discharged from the
cooling water pilot outlet while the engine is
running. (See page 30 for information on the
cooling water pilot outlet.)
EJU32715Multifunction information center check
Make sure that the multifunction information
center operates properly. (See page 39 for in-
1Stern drain plug
2O-ring
1Stern drain plug
2
1
1
UF2T77E0.book Page 72 Monday, July 11, 2016 9:31 AM

Operation
86
EJU40242After removing the watercraft from
the water
NOTICE
ECJ01311
Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.
After operating and removing the watercraft
from the water, promptly discharge the re-
maining water from the cooling water pas-
sages.
To discharge water from the cooling water
passages:
(1) Make sure that the area around the wa-
tercraft is clear, and then start the en-
gine.
(2) Discharge the remaining water out of the
cooling water passages by alternately
squeezing and releasing the throttle lever
quickly for 10 to 15 seconds.
(3) Stop the engine.
UF2T77E0.book Page 86 Monday, July 11, 2016 9:31 AM