2017 VOLVO XC90 headlight bulb

10

Inflating a tire with the tire sealing system compressor477
MAINTENANCE AND SERVICING
Volvo's service program
480
System updates 482
Remote updates 483
Vehicle status 483
Booking service and repairs 484
Wi-Fi connection to a workshop 486
Climate system service 487
Start battery 488
Support battery 490
Battery symbols 491
Fuses 492
Replacing fuses 493
Fuses in the engine compartment 494
Fuses in the passenger compartment 498
Fuses in the cargo compartment 502
Replacing bulbs 505
Removing the rectangular headlight cover 507
Replacing low beam headlight bulbs 508
Replacing High Beam headlight bulbs 509
Replacing front turn signal bulbs 509
Replacing front parking light bulbs 510
Bulb specifications 511
Hoisting the vehicle 512
Opening and closing the hood 514

Engine compartment overview515
Engine oil 516
Checking and refilling engine oil 517
Windshield wipers in the service position 518
Replacing wiper blades 519
Refilling coolant 520
Refilling the windshield washer fluid reservoir 521
Cleaning the exterior 522
Cleaning the interior 525
Cleaning the center display 527
Corrosion protection 527
Paint damage 528
Touching up paint damage 529
Polishing and waxing 529

MAINTENANCE AND SERVICING
}}
505
Replacing bulbs
The halogen headlight bulbs 3
can be replaced
by the owner.
Before the halogen headlight bulbs can be replaced, that plastic covering over the headlighthousing has to be removed and the housing hasto be lifted out of the vehicle.
NOTE
Halogen headlights are not available on all models or in all markets. Consult your Volvo retailer if you are uncertain about the type of headlights in your vehicle.To do so:
Lift the rubber strip by pressing in toward the engine compartment.
Release the pins in the plastic covering's four clips by pressing them down with ascrewdriver or similar object and remove thecovering.
The turn signal, high/low beam, Daytime RunningLight and parking light bulbs will be accessiblewhen the plastic covering has been removed. Put the covering back in place in the reverse order.
NOTE
The pins in the clips have to be pressed back completely before the clips are placed in theplastic covering. When the covering is put back in place, the pins must be pressed so that their upper sur-face is flush with the surface of the clip.
3 Halogen headlights are not available on all models.

||
MAINTENANCE AND SERVICING
506
NOTE
•For information regarding any bulbs not mentioned in this section, please contactyour Volvo retailer or a trained andauthorized Volvo service technician.
• Always switch off the ignition before star-ting to replace a bulb.
• If an error message remains in the dis-play after a faulty bulb has been replaced,contact an authorized Volvo workshop.
• Condensation may form temporarily onthe inside of the lenses of exterior lightssuch as headlights, fog lights, or taillights.This is normal and the lights aredesigned to withstand moisture. Normally,condensation will dissipate after thelights have been on for a short time.
• The optional Active Bending Light bulbscontain trace amounts of mercury. Thesebulbs should always be disposed of by atrained and qualified Volvo service techni-cian.
CAUTION
Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.
WARNING
• The ignition should be switched off com- pletely (be in ignition mode
0) when
replacing bulbs.
• If the engine has been running just prior to replacing bulbs in the headlight hous-ing, please keep in mind that componentsin the engine compartment will be hot.
Front bulbs (vehicles with halogen headlights)
Low beam
High beam
Parking light/Daytime Running Light
Turn signal
Fog light with corner illumination (LED)

MAINTENANCE AND SERVICING
}}
507
Taillight bulbs
Brake light (LED)
Side marker light (LED)
Backup light4
Taillight (LED)
Turn signal (LED)
Fog light (LED)
High-mounted brake light (LED)
Related information
•
Bulb specifications (p. 511)
• Removing the rectangular headlight cover (p. 507) •
Replacing High Beam headlight bulbs(p. 509)
• Replacing low beam headlight bulbs(p. 508)
• Ignition modes (p. 380)
Removing the rectangular headlight cover
Most of the bulbs in the headlight housing can be accessed when the rectangular cover hasbeen removed.
Before the rectangular cover can be removed, the plastic covering must be removed, see the article"Replacing bulbs" for information.
1. Loosen the cover's four screws with a T20 Torx screwdriver (1) but do not remove them completely (turning them 3–4 turns isenough).
2. Push the cover to the side.
3. Remove the cover.Put the cover back in place in the reverse order.
4 Must be replaced by a trained and qualified Volvo service technician.

||
MAINTENANCE AND SERVICING
508
Related information
•Replacing bulbs (p. 505)
Replacing low beam headlight bulbs
On models with halogen headlights, the low beam headlight bulb can be replaced by theowner.
Before the bulb can be replaced, the plastic cov- ering over the headlight housing has to be removed, see the article "Replacing bulbs."
CAUTION
Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.
Driver's side bulb housing shown
1. Remove the low beam round rubber cover from the headlight housing. 2. Remove the connector from the bulb.
3. Remove the bulb by pressing it slightly
upward and then pulling it out.
4. Insert the bulb in the socket. The bulb's guid- ing pin should point straight up.
5. Press the connector into place.
6. Put the rubber cover back into place.
Related information
• Replacing bulbs (p. 505)
• Bulb specifications (p. 511)

MAINTENANCE AND SERVICING
}}
509
Replacing High Beam headlight bulbs
On models with halogen headlights, the High Beam headlight bulb can be replaced by theowner.
Before the bulb can be accessed, the headlight housing's rectangular cover must be removed,see the article "Removing the rectangular head-light cover."
CAUTION
Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vapor-ize in the heat and will leave a deposit on thereflector, which will damage it.Driver's side bulb housing shown
1. Remove the bulb by turning the bulb holder upward and then pulling it straight out.
2. Carefully pry the plastic sleeve by the con- nector's locking lug to release it.
3. Remove the connector from the bulb.
4. Insert a new bulb.
5. Insert the bulb in the socket and turn it downward.
Related information
• Removing the rectangular headlight cover (p. 507)
• Bulb specifications (p. 511)
• Replacing bulbs (p. 505)
Replacing front turn signal bulbs On models with halogen headlights, the front turn signal bulb can be replaced by the owner.
Before the bulb can be accessed, the headlight housing's rectangular cover must be removed,see the article "Removing the rectangular head-light cover."
Driver's side headlight housing shown
1. Press the retaining catches together and pull
the bulb holder straight out.
2. The bulb holder and bulb must be replaced as one unit.
3. Press the new bulb holder into the socket.

||
MAINTENANCE AND SERVICING
510
Related information
•Removing the rectangular headlight cover (p. 507)
• Replacing bulbs (p. 505)
• Bulb specifications (p. 511)
Replacing front parking light bulbs
On models with halogen headlights, the front parking light bulb can be replaced by the owner.
Before the bulb can be accessed, the headlight housing's rectangular cover must be removed,see the article "Removing the rectangular head-light cover." Remove the high beam bulb first by turning the bulb holder upward and then pulling it straightout. This makes it easier to access the parkinglight bulb.
Driver's side bulb housing shown
1. Pull the bulb holder straight out.
2. Remove the bulb by pulling it straight out.
3. Insert a new bulb.
4. Insert the bulb holder in the socket and press it into place. 5. If the high beam bulb was removed, insert
the bulb in the socket and turn downward.
Related information
• Replacing bulbs (p. 505)
• Bulb specifications (p. 511)
• Removing the rectangular headlight cover (p. 507)

MAINTENANCE AND SERVICING
511
Bulb specifications The following specifications apply to models equipped with halogen5
headlights. If other
bulbs need to be replaced, contact a trained and qualified Volvo service technician.
Function [W]A
Type
Low beam 55 H11
High Beam 65 H9
Front turn signal 24 PY24WDaytime running light/ parking light 21/5 W21/5W
A
Watt
Related information
• Replacing bulbs (p. 505)
5
Halogen headlights are not available in all models.