Page 265 of 594

LOCKS AND ALARM
* Option/accessory.263
Deactivate the alarmUnlock and disarm the car alarm as follows:
• press the remote control key's unlock button
• grip one of the door handles 19
or
• push on the tailgate's rubberised pressure plate 19
.
Switching off a triggered alarm
–Press the remote control key's unlock button or set the car in ignition position I by turning
the ignition dial to START and then releas-
ing.
NOTE
• Remember that the alarm is activated when the car is locked.
• If any of the doors are opened from theinside then the alarm is triggered.
Alarm signalsWhen the alarm has been triggered, the following happens:
• A siren sounds for 30 seconds or until thealarm is switched off.
• The direction indicators flash for 5 minutesor until the alarm is switched off. If the cause of alarm activation is not rectified, the alarm cycle is repeated up to 10 times
20
.
Lock and alarm indicator
A red LED on the instrument panel indicates the alarm system's status:
• LED not lit – alarm not armed.
• The LED flashes once every other second –alarm is armed.
• After the alarm has been disarmed, the LEDflashes rapidly for up to 30 seconds or until ignition position
I has been selected by turn-
ing the ignition dial to START and releasing
it - the alarm has been triggered.
Reduced alarm levelReduced guard means that the movement and tilt detectors can be temporarily deactivated. Switch off the movement and tilt detectors in order to avoid accidental triggering of the alarm -e.g. if a dog is left in a locked car or during trans-port on a car train or car ferry. The procedure isthe same as with the temporary disengaging ofthe deadlocks function.
Press the
Reduced guardbutton in the centre display's function view in order to switchoff the movement and tiltdetectors temporarily.
For more information, see the section "Dead- locks".
Related information
•Automatic arming/rearming of the alarm
*
(p. 264)
• Disarming the alarm
* without working remote
control key (p. 264)
• Deadlocks
* (p. 246)
19
Only applies to a car with keyless locking/entry (Passive Entry *)
20 Applies to certain markets.
Page 267 of 594
LOCKS AND ALARM
}}
* Option/accessory.265
Type approval for the remote control key system
Type approval for the remote control key system can be read in the table.Lock system keyless start (Passive Start) and keyless locking/unlocking (Passive Entry *)
CEM marking for the remote control key system. For supplementary type approval number, see the tablebelow.
Country/Area Type approval
Jordan TRC/LPD/2014/250
Serbia P1614120100
Argentina CNC ID: C-14771
Page 388 of 594

||
STARTING AND DRIVING
* Option/accessory.
386
NOTE
To reach level I or II without starting the
engine - do not depress the brake pedal, or
the clutch pedal for cars with manual gear changing, when these ignition positions are tobe selected.
• Ignition position I
- Turn the ignition dial to
START and release it. The control automati-
cally returns to its starting position.
• Ignition position II
- Turn the ignition dial to
START and hold it in the START position for
approx. 4 seconds. Then release the knob, which automatically returns to its startingposition.
• Back to ignition position 0
- To return to
ignition position 0 from position I and II -
Turn the ignition dial to STOP and release it.
The control automatically returns to its star-ting position.
Related information
• Starting the car (p. 386)
• Switching off the car (p. 387)
• Driver display (p. 90)
Starting the car
The car is started using the remote control key and the start knob in the tunnel console.
Start knob in the tunnel console.
The remote control key is not physically used when starting the car since the car is equippedwith support for keyless starting (Passive Start). To start the car:
1. The remote control key must be inside the car. For cars with Passive Start, the key needs to be located in the front part of thepassenger compartment. With the keyless locking/unlocking option (Passive Entry *),
the key can be anywhere in the car. 2. For cars with automatic gear changing, make
sure that gear position P or N is selected.
For cars with manual gear changing, make sure that the gear lever is in neutral positionand that either the clutch pedal or the brakepedal is depressed.
3. Depress the brake pedal fully 1
.
4. Turn the start knob to START and release it.
The control automatically returns to its star-ting position.
NOTE
For diesel-engined cars, there may be a slight delay before starting is initiated.
When the engine is started the starter motor works until the engine is started or until its over-heating protection triggers.
Backup reader's location in the tunnel console.
1 If the car is moving, then you simply need to turn the start knob towards START to start the engine.
Page:
< prev 1-8 9-16 17-24