2017 VOLKSWAGEN CC wheel

help keep the vehicle going in the intended direction. If you are travel-
ing at a speed that causes you to run off the road before ESC can
provide any assistance, you may not experience the benefits of ESC.
ESC includes and/or works together with the ABS, BAS, ASR, EDL,
and XDL systems (see below). ESC is switched on all the time. In
certain situations when you need less traction or additional traction
cannot be achieved, you can switch off ASR by pressing the m button
⇒ fig. 145. Be sure to switch ASR on again when you no longer need
less traction.
Anti-Lock Brake System (ABS)
ABS helps to keep the wheels from locking up and helps to maintain
the driver's ability to steer and control the vehicle. This means the
vehicle is less likely to skid, even during hard braking:
Push the brake pedal down hard and hold it there. Don't take your
foot off the pedal or reduce the force on the pedal!
Do not “pump” the brake pedal or let up on it!
Steer the vehicle while pushing down hard on the brake pedal.
ABS stops working if you release or let up on the brake.
When ABS is doing its job, you will notice a slight vibration through
the brake pedal and hear a noise. ABS cannot shorten the stopping
distance under all conditions. The stopping distance may even be
longer, for instance, when driving on gravel or on newly fallen snow
covering an icy or slippery surface.
Brake Assist (BAS)
The Brake Assist System can help to reduce stopping distances. If
you press the brake pedal very quickly, BAS detects an emergency
situation. It then very quickly builds up full brake system pressure,
maximizing braking power and reducing the stopping distance. This
way, ABS can be activated more quickly and efficiently.
Do not reduce pressure on the brake pedal! BAS switches off auto-
matically as soon as you release or let up on the brake.
Anti-Slip Regulation (ASR)
ASR reduces engine power directed to spinning wheels and adjusts
power to the road conditions. Even under poor road conditions, ASR
can make it easier to get moving, accelerate, and climb hills.

ASR can be switched on or off manually ⇒  Switching Anti-Slip Regu-
lation (ASR) on and off.
Electronic Differential Lock (EDL and XDL)
EDL is applied during regular straight-line acceleration. EDL gently
brakes a drive wheel that has lost traction (spinning) and redirects the
drive force to other drive wheels. In extreme cases, EDL automatical-
ly switches off to keep the brake from overheating. As soon as the
brake has cooled down, EDL automatically switches on again.
XDL is an extension of the Electronic Differential Lock system. XDL
does not react to drive wheel slippage when driving straight ahead.
Instead, XDL detects slippage of the inside front wheel during fast
cornering. XDL applies enough brake pressure to this wheel in order
to stop the slippage. This improves traction, which helps the vehicle
stay on track.

WARNING
Driving fast on icy, slippery, or wet roads can lead to a loss of
control and result in serious personal injury for you and your
passengers.
Always adjust your speed and driving style to road, traffic,
weather, and visibility conditions. Never let the additional safe-
ty that ESC, ABS, BAS, ASR, and EDL can provide tempt you
into taking extra risks.
Braking assistance systems cannot overcome the laws of
physics and always prevent loss of vehicle control. Slippery
and wet roads are still dangerous even with ESC and the other
systems!
Driving too fast on wet roads can cause the wheels to lose
contact with the road and “hydroplane.” A vehicle that has lost
road contact cannot be braked, steered, or controlled.
These systems cannot reduce the risk of accident, for exam-
ple if you drive too fast for conditions or if you do not keep
your distance from the vehicle in front of you.
Although these systems are very effective and can help you
control the vehicle in many difficult situations, always remem-
ber that your vehicle handling control is limited by tire traction.
When accelerating on a slippery surface, for example on ice
and snow, depress the accelerator carefully. Even with these
systems, the wheels may start to spin, leading to a loss of vehi-
cle control.

WARNING
The effectiveness of ESC can be significantly reduced if other
components and systems that affect vehicle dynamics, includ-
ing but not limited to brakes, tires, and other systems men-
tioned above, are not properly maintained or functioning.
Always remember that vehicle alterations or modifications
can affect the functioning of the ABS, BAS, ASR, EDL, and ESC
systems.
Changing the vehicle suspension or using an unapproved
tire/wheel combination can change the way the ABS, BAS, ASR,
EDL, and ESC systems work and reduce their effectiveness.
The effectiveness of ESC is also determined by the tires fitted
⇒  Tires and wheels.
All 4 wheels must be equipped with identical tires in order for
ESC and ASR to work properly. Differences in the tread circumfer-
ence of the tires can cause the system to reduce the engine power
when it is not expected.
If ABS is not working, ESC, ASR, and EDL will also not work.
You may hear noises when these systems are active.
Switching Anti-Slip Regulation (ASR) on and off

Fig. 145 In the center console: Button for switching ASR on and off
manually.

Orientation lines overview
Meaning of the orientation lines projected on the screen ⇒ fig. 154. All
distances of the orientation lines refer to a vehicle on a level surface.
(1) Red: Safety distance. Area up to about 16 inches (40 cm) behind
the vehicle on the road.
(2) Green: Vehicle extension (somewhat wider) toward the rear. The
green area ends about 6 feet (2 meters) behind the vehicle on
the road.
(3) Yellow: The extension of the vehicle to the rear showing the ve-
hicle path as determined by the position of the steering wheel.
The yellow area ends about 10 feet (3 meters) behind the vehicle
on the road.
Parking
Position the vehicle in front of a parking space and shift into Re-
verse.
Slowly back up and steer so that the yellow orientation lines lead
into the parking space (3).
Align the vehicle so that the green and yellow orientation lines are
parallel with the parking space.
Parallel parking (Mode 2)

Fig. 155 On screen: Orientation lines and area of the parking space
behind the vehicle.

When a turn signal is set, unnecessary lines and areas are hidden.
Orientation lines overview
Meaning of the orientation lines and areas projected on screen
⇒ fig. 155. All distances of the orientation lines refer to a vehicle on a
level surface.
(1) Red: Safety distance. Area up to about 16 inches (40 cm) behind
the vehicle on the road.
(2) Vehicle's width limits.
(3) Point to change steering angle.
When the yellow line touches the curb or any other parking
space boundary, the steering wheel must be turned in the oppo-
site direction (close-up view).
(4) The area parallel to the vehicle that is needed for parking. The
area shown must fit completely into the parking space.
(5) Parked vehicle at the curb.
Parking
Position the vehicle about 3 feet (1 meter) away from and parallel
to the parking space and shift into Reverse.
On the screen of the navigation system, activate Mode 2 for paral-
lel parking.
Back up slowly and steer the vehicle so that the yellow surface on
the screen is flush with the side boundary of the parking space (such
as the curb) and stops short of any obstacle (5), such as another ve-
hicle.
Turn the steering wheel as far as it will go into the direction of the
parking space and slowly back up.
Once the yellow line (3) touches the side of the parking space, for
example, a marking or the curb (close-up view), turn the steering
wheel as far as it will go in the opposite direction.
Continue backing up until the vehicles is positioned in the parking
space parallel to the road. If necessary, correct the parking position.
It may take up to 5 seconds for the area detected by the sensors
to be displayed on the factory-installed radio or navigation system
screen.

WARNING
Even if empty, portable fuel containers can leak and cause a
fire and serious personal injuries, especially in a crash.
For your safety, we strongly recommend that you do not
travel with a portable fuel container in your vehicle.
If, under exceptional circumstances, you must transport a
portable fuel container, please observe the following:
– Never fill a portable fuel container while it is anywhere in or
on the vehicle (for example, in the luggage compartment or
on top of the luggage compartment lid). Static electricity can
build up while filling and can ignite fuel vapors, causing a
fire.
– Always place a portable fuel container on the ground be-
fore filling. Never spill fuel inside the vehicle or luggage
compartment. Fuel vapors are highly flammable.
– Always keep the filler nozzle completely inside the portable
container before and during filling.
– If filling a portable container made of metal, the filler nozzle
must always be in contact with the container. This will help
prevent static electricity from discharging and causing a fire.
– Always observe local and state or provincial laws about the
use, storage, and transportation of portable fuel containers.
– Make certain that the portable fuel container meets indus-
try standards, such as ANSI/ASTM F852-86.
NOTICE
Remove fuel spills from the vehicle immediately to help pre-
vent damage to the paint, tires, and wheel housings.
Refueling with gasoline when your vehicle has a diesel engine
or refueling with diesel fuel when your vehicle has a gasoline
engine can cause very serious and expensive engine and fuel
system damage that is not covered by any Volkswagen Limited
Warranty.
If you put any amount of incorrect fuel in the fuel tank, do not
start the engine under any circumstances. Immediately contact
the nearest authorized Volkswagen dealer or authorized
Volkswagen Service Facility for assistance. These fuels contain

Opening the fuel filler cap
Pull the release switch  in the driver door upwards ⇒ fig. 161.
The fuel filler flap is on the right rear side of the vehicle.
Open the fuel filler flap.
Unscrew the fuel cap counterclockwise and remove. Use the slot or
the upper edge of the fuel filler flap to hold the cap while refueling
⇒ fig. 162.
Refueling
The correct fuel grade for your vehicle ⇒  Fuel is listed on a sticker on
the inside of the fuel filler flap ⇒ fig. 162 (arrow).
The fuel tank is full when the automatic filler nozzle pump switches
off the first time ⇒ .
Do not try to add fuel after the pump stops! Topping off the tank in
this way may fill the expansion space that the tank needs and cause
fuel to overflow, for example, if it gets warmer outside.
Closing the fuel filler cap
Screw the fuel cap clockwise onto the fuel filler neck until you hear
it click into place.
Close the fuel filler flap until you hear it latch shut. The fuel filler
flap must be flush with the vehicle body.
WARNING
Spilled fuel can cause fires, explosions, burns, and other se-
vere injuries.
Always stop refueling once the pump nozzle switches off so
that the tank does not overflow.
NOTICE
Remove fuel spills from all vehicle surfaces immediately to help
prevent damage to the paint, tires, and wheel housings.
Fuel spills may pollute the environment.