2017 TOYOTA YARIS GRMN ECU

201
4
4-3. Operating the lights and wipers
Driving
YARIS_GRMN_OM_Europe_OM52J40E
Fog light switch
Turns the front and rear
fog light off
Turns the front fog lights
on
Turns both front and rear
fog light on
Releasing the switch ring
returns it to .
Operating the switch ring
again turns only the rear fog
light off.
■ Fog lights can be used when
Front fog lights: The headlights or the front position lights are turned on.
Rear fog light: The front fog lights are turned on.
The fog lights secure excellent visibility in difficult driving con-
ditions, such as in rain and fog.
Operation instructions

2084-4. Refueling
YARIS_GRMN_OM_Europe_OM52J40E
Pull up the opener to open the
fuel filler door.
Turn the fuel tank cap slowly to
open.
WARNING
■ When refueling
Observe the following precautions to pr event fuel overflowing from the fuel
tank:
● Securely insert the fuel nozzle into the fuel filler neck.
● Stop filling the tank after the fuel nozzle automatically clicks off.
● Do not top off the fuel tank.
NOTICE
■Refueling
Do not spill fuel during refueling.
Doing so may damage the vehicle, such as causing the emission control
system to operate abnormally or damaging fuel system components or the
vehicle’s painted surface.
Opening the fuel tank cap

2816-3. Do-it-yourself maintenance
YARIS_GRMN_OM_Europe_OM52J40E
6
Maintenance and care
Firmly tighten each wheel nut
two or three times in the order
shown in the illustration.
Tightening torque:
103 N·m (10.5 kgf·m, 76 ft·lbf)
Stow the tire, jack and all tools.
WARNING
■ After using the tools and jack
Before driving, make sure all the tools and jack are securely in place in their
storage location to reduce the possibility of personal injury during a collision
or sudden braking.

3006-3. Do-it-yourself maintenance
YARIS_GRMN_OM_Europe_OM52J40E
■Halogen headlights
Turn the bulb base counter-
clockwise.
Pull the bulb out while press-
ing the lock release of the
connector.
Replace the light bulb, plug
the connector, and then
install the bulb base.
Align the 3 tabs on the light bulb
with the mounting and insert.
Turn and secure the bulb
base.
Shake the bulb base gently to
check that it is not loose, turn
the headlights on once and visu-
ally confirm that no light is leak-
ing through the mounting.
Replacing light bulbs

3026-3. Do-it-yourself maintenance
YARIS_GRMN_OM_Europe_OM52J40E
Unplug the connector while
pressing the lock release.
Turn the bulb base counter-
clockwise.
Set the new light bulb.
Align the 3 tabs on the light bulb
with the mounting, and insert.
Turn and secure the bulb.

3066-3. Do-it-yourself maintenance
YARIS_GRMN_OM_Europe_OM52J40E
After installing the new bulb,
secure the bulb base to the
mirror body.
Align the tabs, and secure
the mirror by pushing in each
diagonally-opposite pair of
tabs in order.
Make sure to insert the tabs in
order as shown in the illustra-
tion, and push them in until a
click is heard.
If you do not hear the click, do
not force the tabs in. Instead,
remove the mirror and check
that the tabs are aligned.

3086-3. Do-it-yourself maintenance
YARIS_GRMN_OM_Europe_OM52J40E
Install the new bulb.
Turn and secure the bulb
base.
Install the cover.
Align the cover claws with
the notches.
Press the cover until it is
fixed.

3146-3. Do-it-yourself maintenance
YARIS_GRMN_OM_Europe_OM52J40E
WARNING
■Replacing light bulbs
● Turn off the lights. Do not attempt to replace the bulb immediately after
turning off the lights.
The bulbs become very hot and may cause burns.
● Do not touch the glass portion of the light bulb with bare hands. When it is
unavoidable to hold the glass portion, use and hold with a clean dry cloth
to avoid getting moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
● Fully install light bulbs and any parts used to secure them. Failure to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
■ To prevent damage or fire
● Make sure bulbs are fully seated and locked.
● Check the wattage of the bulb before installing to prevent heat damage.