2017 TOYOTA YARIS GRMN display

942. Instrument cluster
YARIS_GRMN_OM_Europe_OM52J40E
The indicators inform the driver of the operating state of the vehicle’s
various systems.
*1: These lights turn on when the engine switch is turned to IGNITION ON
mode to indicate that a system check is being performed. They will turn off
after the engine is started, or after a few seconds. There may be a mal-
function in a system if a light does not come on, or if the lights do not turn
off. Have the vehicle inspected by any authorized Toyota retailer or Toyota
authorized repairer, or any reliable repairer.
*2: The light flashes to indicate that the system is operating.
*3: The light illuminates on the multi-information display.
*4: This light illuminates on the center panel.
Indicators
Turn signal indicator
( P. 194)
*1, 2
Slip indicator (P. 2 11 )
Headlight high beam
indicator ( P. 197)
*1
VSC off indicator
( P. 212)
Tail light indicator
( P. 196)
*3Ice warning indicator
( P. 96)
Front fog light indicator
( P. 201)
*4
Rear fog light indicator
( P. 201)
“PASSENGER AIR BAG” indicator
( P. 5 0 )

962. Instrument cluster
YARIS_GRMN_OM_Europe_OM52J40E
Gauges and meters
Tachometer
Displays the engine speed in revolutions per minute.
Outside temperature display
Displays the outside temperature within the range of -40°C (-40°F) to 50°C
(122°F). Low outside temperature indicator comes on when the ambient
temperature is 3°C (37°F) or lower.
Clock
Displays the current time. ( P. 104)
Speedometer
Displays the vehicle speed.
Fuel gauge
Displays the quantity of fuel remaining in the tank.

972. Instrument cluster
2
Instrument cluster
YARIS_GRMN_OM_Europe_OM52J40E
Odometer and trip meter display:
Displays the following items.
Odometer:
Displays the total distance the vehicle has been driven.
Trip meter:
Displays the distance the vehicle has been driven since the meter was last
reset. Trip meters “A” and “B” can be used to record and display different
distances independently.
Multi-information display
Presents the driver with a variety of driving-related data. ( P. 1 0 0 )
Displays warning messages in case of a malfunction. ( P. 332)
Engine coolant temperature gauge
Displays the engine coolant temperature.
Switches the items of the odome-
ter and trip meter display by
pressing the “TRIP” switch.
When the trip meter is displayed,
pressing and holding the “TRIP”
switch will reset the trip meter.
Changing the display

982. Instrument cluster
YARIS_GRMN_OM_Europe_OM52J40E
The brightness of the instrument cluster lights can be adjusted.
Display the instrument cluster light
control by pressing the “TRIP”
switch.
Then, press and hold the switch.
Adjust the brightness to the
desired level by pressing the
switch.
■ The meters and display illuminate when
The engine switch is in IGNITION ON mode.
■ Instrument cluster brightness adjustment
The brightness level of the meters when the surroundings are day mode and
night mode can be adjusted individually.
• Day mode: When the headlight switch is off or when the headlight switch
is on but the surrounding area is bright.
• Night mode: When the headlight switch is on and the surrounding area is
dark.
Instrument cluster light control

992. Instrument cluster
2
Instrument cluster
YARIS_GRMN_OM_Europe_OM52J40E
■ Outside temperature display
● In the following situations, the correct outside temperature may not be dis-
played, or the display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 20 km/h [12 mph])
• When the outside temperature has changed suddenly (at the entrance/
exit of a garage, tunnel, etc.)
● When “--” or “E” is displayed, the system may be malfunctioning.
Take your vehicle to any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
● The temperature range that can be displayed is from -40°C (-40°F) to 50°C
(122°F).
NOTICE
■ To prevent damage to the engine and its components
● Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
● The engine may be overheating if the engine coolant temperature gauge is
in the red zone (“H”). In this case, immediately stop the vehicle in a safe
place, and check the engine after it has cooled completely. ( P. 363)

1002. Instrument cluster
YARIS_GRMN_OM_Europe_OM52J40E
Multi-information display
The multi-information display presents the driver with a variety of vehi-
cle data.
● Menu icons
Displays the following informa-
tion when an icon is selected.
( P. 101)
Some of the information may be
displayed automatically
depending on the situation.
Drive information
Select to display various drive data. ( P. 102)
Navigation system-linked display (if equipped)
Select to display the following navigation system-linked information.
• Route guidance
• Compass display (north-up display/heading-up display)
Audio system-linked display
Select to enable selection of an audio source or track on the meter
using the meter control switches.
Display contents

1012. Instrument cluster
2
Instrument cluster
YARIS_GRMN_OM_Europe_OM52J40E
Warning message display
Select to display warning messages and measures to be taken if a
malfunction is detected. ( P. 332)
Settings display
Select to change the meter display settings and the operation set-
tings of some vehicle functions. ( P. 103)
The multi-information display is
operated using the meter control
switches.
Select an item/change pages
Enter/set
Return to the previous screen
Operating the meter control switches

1022. Instrument cluster
YARIS_GRMN_OM_Europe_OM52J40E
Items displayed can be switched by pressing “<” or “>” of the meter
control switches to select and pressing “ ” or “”.
● Average fuel consumption (after reset*/after start/after refuel)
Displays the average fuel consumption since the function was reset, the
engine was started, and the vehicle was refueled, respectively
Use the displayed average fuel consumption as a reference.
● Average vehicle speed (after reset*/after start)
Displays the average vehicle speed since the function was reset and the
engine was started, respectively
● Elapsed time (after reset*/after start)
Displays the elapsed time since the function was reset and the engine was
started, respectively
● Distance (driving range/after refuel)
Displays the estimated maximum distance that can be driven with the
quantity of fuel remaining
• This distance is computed based on your average fuel consumption. As
a result, the actual distance that can be driven may differ from that dis-
played.
• When only a small amount of fuel is added to the tank, the display may
not be updated.
When refueling, turn the engine switch off. If the vehicle is refueled with-
out turning the engine switch off, the display may not be updated.
● Speedometer
Displays the vehicle speed.
●Display off
A blank screen is displayed
*: The function can be reset by pressing and holding the of the meter
control switches when the reset item is displayed.
Drive information