2017 SUZUKI CELERIO engine

2-7
BEFORE DRIVING
76MH1-74E
76MH1-74E
Security System (if equipped)
The security system is armed in about 5 seconds after you lock all doors (includingthe tailgate) by using the keyless entry sys- tem transmitter. Once the system is armed, any attempt toopen a door by using any other means (*) than the keyless entry system transmitter, or open the engine hood, will cause thealarm to be triggered. * These means include the following:–The key – The lock knob on a door – The central door locking switch
Also, in case that you have set the shocksensor to enabled state and set sensitivity of the pre-warning function and full blastwarning function to a level other than 0, the alarm will be triggered if any attempt to tamper with the vehicle. The shock sensorcan be selected enabled or disabled state, and sensitivity of each warning can be adjusted as desired. To set the shock sen-sor, ask your MARUTI SUZUKI dealer or use the setting mode of the information display.
NOTE: • The default setting of the shock sensoris in the disabled state. Set to the enabled state and adjust sensitivity of each warning according to your prefer- ence. For details on how to use the infor-mation display, refer to “Information Display” in this section.• Your dealer may have already set theshock sensor of the vehicle to theenabled state before you purchase it. Consult your dealer for further informa-tion.
NOTE:• The security system generates alarmswhen any of the predetermined condi-tions is met. However, the system doesnot have any function of blocking unau- thorized entry into the vehicle.• Always use the keyless entry systemtransmitter to unlock the doors when thesecurity system has been armed. Using a key instead will trigger the alarm.• If a person who does not know the secu-rity system is going to drive the vehicle,we recommend you explain the systemand its operation to the person, or dis- able the system beforehand. Mistakenly triggering the alarm may cause a nui-sance to others.• Even if the security system is armed,you should still be careful to guardagainst theft. Do not leave money or things of value in the vehicle.
How to arm the security system
(when enabled)Lock all doors (including the tailgate) using the keyless entry system transmitter. Thesecurity system indicator (1) will start blink- ing rapidly, and the security system will be armed in about 5 seconds.While the system is being armed, the indi- cator continues to blink at intervals of approximately 2 seconds.
With tachometer
76MH0B001
(1)
18

2-8
BEFORE DRIVING
76MH1-74E
76MH1-74E
Without tachometer
76MH0B002
NOTE: • To prevent the alarm from being acci-dentally triggered, avoid arming it while anyone remains inside the vehicle. The alarm will be triggered if any person inside opens the door or engine hood, orswings the vehicle (if the shock sensor is in the enabled state).• The security system is not armed whenall doors are locked using the key fromoutside, or using the door lock knobs or the central door locking switch frominside.• If any door is not operated within approx-imately 30 seconds after the doors havebeen unlocked using the keyless entry system transmitter, the doors are auto-matically locked again. When the doors are locked, the security system will be
armed in about 5 seconds if the system is in the enabled state.• If the security system indicator (1) blinkswhen the ignition switch is in the “ON”position, there may be something wrong with the security system. Ask your MAR-UTI SUZUKI dealer to inspect the sys- tem.
How to disarm the security systemSimply unlock the doors using the keyless entry system transmitter. The security sys-tem indicator will go out, indicating that the security system is disarmed.
How to stop the alarm Should the alarm be triggered accidentally, unlock the doors using the keyless entrysystem transmitter, or insert the key in the ignition switch and turn it to “ON” position. The alarm will then stop.
NOTE: • Even after the alarm has stopped, if youlock the doors using the keyless entry system transmitter, the security system will be rearmed with a delay of about 5seconds.• If you disconnect the battery while thesecurity system is in the armed conditionor the alarm is actually in operation, the alarm will be re-triggered when the bat- tery is then reconnected.• Even after the alarm has stopped at theend of the predetermined operation time,it will be triggered again if any of thedoors or engine hood is opened, or the
vehicle feels a shock (if the shock sen- sor is in the enabled state), without dis- arming the security system.
Checking whether the alarm has beentriggered during parkingIf the alarm was triggered and you then turn the ignition switch to “ON” position, the security system indicator will blink rapidlyfor about 8 seconds and a buzzer will beep 4 times during this period. If this happens, check whether the vehicle has been bro-ken into while you were away from it.
Enabling and disabling the security system The security system can be either enabled or disabled.
When enabled If any of the doors are opened withoutunlocking by the keyless entry system transmitter, all turn signal lights start to blink and the interior buzzer beeps inter-mittently. After 5 seconds, the siren will sound for about 27.5 seconds. The secu- rity system indicator continues to blinkduring this time. If the engine hood is opened, all turn sig-nal lights blink, and the siren sounds forabout 27.5 seconds. The security sys- tem indicator continues to blink during this time.
(If the shock sensor is in the enabled state) If the vehicle feels a shock, the sirensounds for about 2 seconds (pre-warn- ing). If the vehicle continues to feel a
(1)
19

2-29
BEFORE DRIVING
76MH1-74E
76MH1-74E
Speedometer
The speedometer indicates vehicle speed.
Tachometer (if equipped)
The tachometer indicates engine speed in revolutions per minute.
Fuel Gauge
With tachometer
76MH0A037
Without tachometer
76MH0A038
When the ignition switch is in the “ON” position, this gauge gives an approximate indication of the amount of fuel in the fueltank. “F” stands for full and “E” stands for empty.
If the fuel meter indicator shows only one segment to “E”, refill the tank as soon aspossible.
NOTE: If the last segment blinks, it means that thefuel is almost empty.
If the low fuel warning light (1) comes on, fill the fuel tank immediately.
NOTE:The activation point of the low fuel warning light (1) varies depending on road condi- tions (for example, slope or curve) anddriving conditions because of fuel moving in the tank.
Refer to “Low Fuel Warning Light” in“Warning and Indicator Lights” in this sec- tion for details.
The mark (2) indicates that the fuel filler door is located on the left side of the vehi-cle.
Brightness Control
76MH0A039
When the ignition switch is turned to the“ON” position, the pointer lights come on.
Your vehicle has a system to automaticallydim the brightness of the instrument panellights when the position lights or headlights are on.
When the position lights and/or headlights are ON, you can control the meter illumina- tion intensity.
NOTICE
Never drive the vehicle with theengine revving in the red zone, orsevere engine damage can result. Keep the engine speed below the red zone even when downshifting to alower gear position. Refer to “Down- shifting maximum allowable speeds” in the “OPERATING YOUR VEHICLE”section.
(1)(2)
EXAMPLE
(1)
(2)
EXAMPLE(1)
EXAMPLE
40

2-37
BEFORE DRIVING
76MH1-74E
76MH1-74E
76MH0017
NOTE: • As shown in the above illustration,“ ” indicates on the display of cur- rently setting item.• To go back to the higher level displayduring operation, turn the indicatorselector knob (2) to display “bACK” or“-bAC” and then push the indicatorselector knob (2).• If the security system “S1” is in the dis-abled state, the shock sensor “S2”, pre-warning sensitivity “S3” and full blastwarning sensitivity “S4” cannot be setup.
5) To exit the setting mode, switch the dis-play to show “End” and then push theindicator selector knob (2).
Warning and Indicator Lights
Brake System Warning Light
65D477
Three different types of operations existdepending on the vehicle’s specification.
1) The light comes on briefly when theignition switch is turned to the “ON” position.2) The light comes on when the parkingbrake is engaged with the ignition switch in the “ON” position.3) The light comes on when under eitheror both of above two conditions.
The light also comes on when the fluid in the brake fluid reservoir falls below the specified level.The light should go out after starting the engine and fully releasing the parking brake, if the fluid level in the brake fluid res-ervoir is adequate. The light also comes on together with the ABS warning light when the rear brakeforce control function (proportioning valve function) of the ABS system fails. If the brake system warning light comes onwhile you are driving the vehicle, it may mean that there is something wrong with
the vehicle’s brake system. If this happens,you should:
1) Pull off the road and stop carefully.
2) Test the brakes by carefully starting andstopping at the side of the road.– If you determine that it is safe, drivecarefully at low speed to the nearest dealer for repairs, or– Have the vehicle towed to the nearestdealer for repairs.
EXAMPLE
WA R N I N G
Remember that stopping distancemay be longer, you may have to push harder on the pedal, and the pedal may go down farther than normal.
WA R N I N G
If any of the following conditions occur, you should immediately ask your MARUTI SUZUKI dealer toinspect the brake system. • If the brake system warning lightdoes not go out after the engine has been started and the parking brake has been fully released.• If the brake system warning lightdoes not come on when the igni-tion switch is turned to the “ON” position.• If the brake system warning lightcomes on at any time during vehi-cle operation.
48

2-38
BEFORE DRIVING
76MH1-74E
76MH1-74E
NOTE: Because the disc brake system is self- adjusting, the fluid level will drop as thebrake pads become worn. Replenishing the brake fluid reservoir is considered nor- mal periodic maintenance.
NOTE: (Parking Brake Reminder Buzzer) (ifequipped) A buzzer sounds intermittently to remind you to release the parking brake if youstart the vehicle without releasing the park- ing brake. Make sure that the parking brake is fully released and the brake sys-tem warning light turns off.
Seat Belt Warning Light
(if equipped)
60G049
This light blinks as a reminder until the driver’s seat belt is buckled.
For details about the seat belt reminder, refer to “Seat Belts and Child Restraint Systems” in this section.
“AIR BAG” Light (if equipped)
63J030
This light blinks or comes on for severalseconds when the ignition switch is turned to the “ON” position so you can check if the light is working.
The light will come on and stay on if there is a problem in the air bag system (ifequipped).
Anti-Lock Brake System (ABS)
Warning Light (if equipped)
65D529
When the ignition switch is turned to the “ON” position, the light comes on briefly so you can check that the light is working. If the light stays on, or comes on whendriving, there may be something wrong with the ABS.
If this happens: 1) Pull off the road and stop carefully.2) Turn the ignition switch to “LOCK” andthen start the engine again.
If the warning light comes on briefly then turns off, the system is normal. If the warn- ing light still stays on, the system will besomething wrong.
If the light and the brake system warning light stay on, or come on simultaneously when driving, your ABS system is equipped with the rear brake force controlfunction (proportioning valve function) and there may be something wrong with both the rear brake force control function andanti-lock function of the ABS system.
WA R N I N G
If the “AIR BAG” light does not blinkor come on briefly when the ignition switch is turned to the “ON” position,stays on for more than 10 seconds, or comes on while driving, the air bag system (if equipped) may not workproperly. Have both systems inspected by an authorized MARUTI SUZUKI dealer.
49

2-39
BEFORE DRIVING
76MH1-74E
76MH1-74E
If one of these happens, have the system inspected by your MARUTI SUZUKI dealer. If the ABS becomes inoperative, the brake system will function as an ordinary brake system that does not have this ABS sys-tem.
Malfunction Indicator Light
63J031
Your vehicle has a computer-controlledemission control system. A malfunctionindicator light is provided on the instrument panel to indicate when it is necessary to have the emission control system serviced.The malfunction indicator light comes on when the ignition switch is turned to “ON” position to let you know the light is workingand goes out when the engine is started.
If the malfunction indicator light comes on when the engine is running, there is a damage with the emission control system.Bring the vehicle to your MARUTI SUZUKI dealer to have the damage fixed.
Also, if the light comes on, there may be something wrong with the Auto Gear Shift system. Have the system inspected by an authorized MARUTI SUZUKI dealer.
Transaxle Warning Light
(if equipped)
80J219
This light comes on for several seconds when the ignition switch is turned to the “ON” position so you can check the light isworking. If this light comes on when the engine is running, there is a problem with the AutoGear Shift system. Ask your MARUTI SUZUKI dealer to have the system inspected.
NOTE: If the Auto Gear Shift system temperaturebecomes too high, this light will blink. Stop the vehicle in a safe place and let the sys- tem cool down.
Electric Power Steering Light
79J039
This light comes on when the ignitionswitch is turned to the “ON” position, and goes out when the engine is started.
If this light comes on while driving, the power steering system may not work prop- erly. Have the system inspected by yourMARUTI SUZUKI dealer.
NOTE: Following operations of the steering wheel while parking or driving at a very low- speed may have steering effort biggergradually. This is not a malfunction of the steering system, but the power steering control system limits the power assist inorder to prevent them from overheating. • The steering wheel is operated veryoften.• The steering wheel is kept in a fullyturned position for a long while. When the power steering control system cool down, the power steering system back to the original condition. However, repeating these operations couldcause the power steering system dam-aged.
NOTICE
Continuing to drive the vehicle whenthe malfunction indicator light is oncan cause permanent damage to the vehicle’s emission control system, and can affect fuel economy anddriveability.
50

2-40
BEFORE DRIVING
76MH1-74E
76MH1-74E
NOTE: If the power steering system does not work properly, you will feel heavier to steer butyou still will be able to steer.
NOTE: If the steering is operated, you may hear a noise. This is normal and indicates that the power steering system works properly.
Oil Pressure Light
50G051
This light comes on when the ignition switch is turned to the “ON” position, and goes out when the engine is started. Thelight will come on and remain on if there is insufficient oil pressure. If the light comes on when driving, pull off the road as soonas you can and stop the engine. Check the oil level and add oil if necessary. If there is enough oil, the lubrication sys-tem should be inspected by your MARUTI SUZUKI dealer before you drive the vehi- cle again.
Charging Light
50G052
This light comes on when the ignitionswitch is turned to the “ON” position, and goes out when the engine is started. The light will come on and remain on if there issomething wrong with the battery charging system. If the light comes on when theengine is running, the charging system should be inspected immediately by your MARUTI SUZUKI dealer.
High Engine Coolant Temperature
Warning Light (red color)
54G344
When the ignition switch is turned to the “ON” position, this light comes on briefly soyou can check that the light is working. If this light blinks while driving, it means the engine is running hot. Avoid driving condi-tions that may lead to actual overheating. If the light stays on without blinking, then the engine is overheating. Follow the instruc-tions in the “If the Engine Overheats” of “EMERGENCY SERVICE” section.
NOTICE
• If you operate the engine with thislight on, severe engine damage can result.• Do not rely on the Oil PressureLight to indicate the need to addoil. Be sure to periodically check the engine oil level.
NOTICE
Continuing to drive the vehicle whenengine overheating is indicated can result in severe engine damage.
51

2-41
BEFORE DRIVING
76MH1-74E
76MH1-74E
Immobilizer System Light
80JM122
When the ignition switch is turn to the “ON” position, this light comes on briefly so you can check that the light is working. If thislight brinks with the ignition switch is turn to the “ON” , the engine will not start.
NOTE: If this light blinks, turn the ignition switch to the “LOCK” position, then turn it back to the “ON” position. If the light still blinks with the ignition switchturned to the “ON” position, there may be something wrong with your key or with the immobilizer system. Ask your MARUTISUZUKI dealer to inspect the system.
Open Door Warning Light
54G391
This light remains on until all doors (includ-ing the tailgate) are completely closed.
If any door (including the tailgate) is open when the vehicle is moving, a ding sounds to remind you to close all doors completely.
Low Fuel Warning Light
54G343
If this light comes on, fill the fuel tankimmediately.
When this light comes on, a ding sounds once to remind you to fill the fuel. If you do not fill the fuel, a ding sounds every time when the ignition switch isturned to the “ON” position.
NOTE: The activation point of this light varies depending on road conditions (for exam- ple, slope or curve) and driving conditionsbecause of fuel moving in the tank.
Turn Signal Indicators
50G055
When you turn on the left or right turn sig- nals, the corresponding green arrow on the instrument panel will flash along with therespective turn signal lights. When you turn on the hazard warning switch, both arrows will flash along with all of the turnsignal lights.
Main Beam (high beam) Indicator
Light
50G056
This indicator comes on when headlight main beams (high beams) are turned on.
Security System Indicator
(if equipped)
82K269
For details about the security system, referto “Security System” in this section.
52