2017 SUBARU OUTBACK wheel

Adaptive Cruise Control
49
●Automatic cancellation by the system
In the following cases, a buzzer will sound a
single long beep and Adaptive Cruise
Control is automatically canceled. ( is
displayed on the EyeSight display area.) If
the stay-stopped function is engaged, the
electronic parking brake will be automati-
cally engaged.
x Conditions for automatic cancellation
- The grade of the road is very steep.
- ABS, Vehicle Dynamics Control or Traction Control Function is activated.
- The vehicle speed has exceeded approximately 100 MPH (160 km/h) while cruise con- trol is set.
- The steering wheel was turned significantly in either direction.
- The transmission select lever is moved to a position other than . xCruise control can be resumed after the transmission select lever is returned to the
position.
- A paddle shift switch is operated while driving when the transmission select lever is in the position.
xCruise control can be resumed again after the shift indicator returns to .
- Any door (except the rear gate/trunk) is opened.
- The driver’s seatbelt is unfastened.
- The electronic parking brake is engaged manually. (When the brake system warning light is illuminated or flashing.)
- The X-mode is turned on (the X-mode indicator light illuminates). xCruise control can be resumed after the X-mode is turned off.
- EyeSight operation has temporarily stopped.
Ÿ Refer to page 87.
- EyeSight is malfunctioning.
Ÿ Refer to page 86.
- The Pre-Collision secondary braking has activated.
S02326
D
D
D
D

54
Lane Keep Assist
The stereo cameras detect lane markings
(including Botts’ dots) of the lane and the sys-
tem assists the steering operation by working
with the electric power steering to help keep
your vehicle in its lane when driving on
expressways, freeways and interstate high-
ways.
WARNING
Lane Keep Assist is not an automatic driving system.
Do not overestimate the capabilities of Lane Keep Assist. It is not a sys-
tem to assist inattentive driving or meant to permit driving without hold-
ing the steering wheel. Make sure to grip the steering wheel while
driving. To drive safely, check the distance from the vehicle in front or
from a vehicle driving in parallel with your vehicle, the surrounding con-
ditions and the surrounding environment while driving.
If you feel that the level of control and timing by the system are different from
your own driving style, the system may not support safe driving. Do not use
Lane Keep Assist.
Lane Keep Assist does not always operate under all situations. If you rely
only on the Lane Keep Assist to stay in a lane, it may cause an accident such
as a collision with an obstacle beside your lane or with a vehicle driving in an
adjacent lane.x Check that there are no problems with the tires and brakes during a daily
inspection before using the system.
Ÿ Refer to “Warranty and Maintenance Booklet”.
x The system may not operate properly under the following conditions. Do
not use Lane Keep Assist.
- The air pressure of tires is not to specification.
*1
- Tires that are unevenly worn or tires with uneven wear patterns are installed.*1
- Tires that are the wrong size are installed.*1
- The wheel balance is abnormal (e.g., the balance weight is removed ormisaligned.)*1
- The wheel alignment is out of the specified value.*1
- Flat tires have been fixed temporarily with a tire repair kit.
- The suspension has been modified (including genuine SUBARU parts).
S02069
Lane
markings

Lane Keep Assist
55
Continued on next pageŸ
- Any object that disturbs the stereo cameras’ view is installed on the vehi-
cle.
- Tire chains are installed.
- When you feel an abnormal vibration in the steering wheel or feel the steering wheel is heavier than usual.
- The steering wheel has been replaced with parts other than genuine SUBARU parts.
- The headlights are dirty or they have snow, ice or dirt on them. (Objects are not adequately illuminated and are difficult to detect.)
- The headlights are not aligned correctly. (Objects are not adequately illu- minated and are difficult to detect.)
- The headlights and fog lamps, and other lights, have been modified.
- Vehicle operation has become compromised due to an accident or mal- function.
- The brake system warning light (red) is illuminated.
- A heavy cargo is loaded onto or inside the vehicle.
- The maximum number of occupants is exceeded.
- Your vehicle is towing a vehicle, etc.
- There is something wrong with the combination meter. For example, an indicator light or a warning light in the combination meter does not prop-
erly turn on or off, a beep does not sound, or the indication on the liquid-
crystal display is different from when it is normal.
*2
*1: The wheels and tires have critically important functions. Be sure to
use the appropriate ones.
For details, refer to the Owner’s Manual for your vehicle.
*2: For details about the functions and operations of the combination meter, refer to the Owner’s Manual for your vehicle.
x Lane Keep Assist is designed for use on expressways, freeways, toll
roads, interstate highways and similar limited access roads. In the follow-
ing conditions, do not use Lane Keep Assist. Doing so may result in an
accident.
- Ordinary roads (roads other than those mentioned above)
- Roads with sharp curves
- Roads with lane restric- tions or tentative lanes due
to construction work, etc.
- Old lane markings remain.
- Snow, puddles or snow melting agents remain on
the road surface.
- Cracks or constructed traces remain on the road
surface.
S02059

Lane Keep Assist
59
Press the (Lane Keep Assist) switch once again to turn it off, and “ ” (Lane Keep
Assist indicator) is turned off on the EyeSight display area.
The Lane Departure Prevention Function goes into the standby status, and the lane indica-
tor illuminates when all of the following conditions are met.x The vehicle speed is between approximately 40 MPH (65 km/h) and 90 MPH (145 km/h).
x The system is detecting the lane markings.
x The driver is holding the steering wheel.
x When driving on a road that has a lane width that is between approximately 10 ft (3 m)
and 15 ft (4.5 m).
x When driving on a straight road or gentle curve.
x When driving near the center of a lane.
When the vehicle is about to depart from the lane, Lane Departure Prevention Function
starts to operate and “ ” (Lane Keep Assist indicator) illuminates in green while it is
operating.
NOTE
x If you just lightly put your hands on the steering wheel for a certain period
of time or if you do not operate the steering wheel, the function will auto-
matically be canceled. (“ ” Lane Keep Assist indicator) illuminates in
white again.)
x Lane Departure Prevention Function operates when the system deter-
mines that the vehicle will depart from the lane if you continue to drive in
the same manner. Therefore, it operates at an earlier timing than Lane
Departure Warning (
Ÿ Refer to page 68.) (it may depend on the surround-
ing environment and road condition).
x The lane indicator in the standby status and in operation may illuminate
only on the left side or right side.
milesA
MPG
milesA
MPG
milesA
MPG
S02045
Lane Keep
Assist
indicator
(white)
Turned on Standby status In operation
(white) (green)

Lane Keep Assist
60
■Canceling Lane Departure Prevention Function
●
Cancellation by the operation of a driver (In case no beep sounds)
The following operation cancels Lane Departure Prevention Function.
If the function is canceled, “ ” (Lane Keep Assist indicator) and the lane indicator are
turned off on the EyeSight display area. x Press the (Lane Keep Assist) switch.
Either of the following operations temporarily cancels the Lane Departure Prevention Function.
While temporarily canceling the function, “ ” (Lane Keep Assist indicator) on the
EyeSight display area illuminates in white and the lane indicator is turned off. x Depressing the brake pedal
x Operating the turn signal lever
x When the system determines that the driver operates the steering wheel to make a lane
change.
x Turning on the hazard warning flasher switch
●Automatic cancellation by the system (An audible beep will sound.)
Under the following conditions, a beep sounds and the Lane Departure Prevention Function
is temporarily canceled.
While the function is temporarily canceled, “ ” (Lane Keep Assist indicator) on the
EyeSight display area illuminates in white and the lane indicator is turned off.
x When the system cannot detect the lane.
x The windshield wiper operates at a high speed.
x The vehicle speed is less than approximately 37 MPH (60 km/h) or is more than approxi-
mately 93 MPH (150 km/h).
x The ABS, the Vehicle Dynamics Control or the Traction Control System operates.
x Either the driver’s door, the front passenger’s door or the rear door is open.
x The seatbelt of driver’s seat is unfastened.
x The electronic parking brake is applied (The electric parking brake indicator light illumi-
nates or blinks).
x The select lever is shifted to a position other than or position.
x The system could not detect the steering
operation by the driver for a certain period of
time.
- When the system detected no steering operation, the interruption screen appears
on the multi information display. The inter-
ruption screen continues to appear until
the system detects the steering operation.
If the system still cannot detect the steer-
ing operation, the Lane Departure Preven-
tion Function is automatically canceled.
DM
milesA
MPG
Keep Hands OnSteering Wheel
S02046

Pre-Collision Throttle Management
65
Continued on next pageŸ
CAUTION
xIn the following situations, turn off Pre-Collision Throttle Management. Other-
wise Pre-Collision Throttle Management may activate unexpectedly.
- When the vehicle is being towed
- When loading the vehicle onto a carrier
- When a chassis dynamometer, free-rollers or similar equipment is used
- When a mechanic lifts up the vehicle, starts the engine and allows the wheels to spin freely
- When passing hanging banners, flags or branches, or when thick/tall vege- tation is contacting the vehicle
x The Pre-Collision Throttle Management may activate in the following situa-
tions. Therefore concentrate on safe driving.
- When your vehicle is close to the vehicle in front
- When passing through an automatic gate
- When your vehicle is in a location where the grade of the road changes rapidly
- When passing through clouds of steam or smoke
S01264
S00652

Lane Departure Warning
69
CAUTION
In the following situations, the Lane Departure Warning will or may not acti-
vate:x Vehicle speed is approximately 30 MPH (50 km/h) or less.
x When the steering wheel is turned significantly to either side
x When the vehicle is driving around a curve whose radius is 0.18 miles (300
m) or smaller.
x When the brake pedal is depressed or immediately after it is depressed
x When the following distance behind a vehicle in front is short
x While the turn signal is operating and for approximately 4 seconds after the
turn signal lever has returned to its original position
x For approximately 4 seconds after the hazard lamp has switched off
x When the vehicle has not returned to the inside of the lane after the Lane
Departure Warning has activated
x The lane is narrow.
x When it is difficult for the camera to detect lane markings
- There are no lane markings or they are very worn.
- The lane markings are yellow.
- It is difficult to detect lane markings as they are similar in color to the road surface.
- The lane markings are narrow.
NOTE
x The following situations may cause incorrect lane detection and a faulty
Lane Departure Warning to occur.
- Tire tracks on a wet road or snow-covered road
- Boundaries between snow and asphalt, marks from road repair, etc.
- Shadows of guardrails
- Lane markings are drawn in double
- There are some lane markings left from roadwork or markings from the previous road.
x When the Lane Departure Warning OFF indicator light is illuminated, the
Lane Departure Warning is inactive.
Ÿ Refer to page 70.

Conventional Cruise Control
77
(2) Switch to Conventional Cruise Control. Press and hold the / (following distance setting) switch for approximately 2
seconds or longer to switch from Adaptive Cruise Control to Conventional Cruise
Control. A buzzer sounds 1 short beep.
At this time, the following distance setting indicator on the EyeSight display area of the
multi information display turns off and (Conventional Cruise Control) is displayed.
To set the ready status:
Conventional Cruise Control can be set when
all of the following conditions are met and is displayed on the EyeSight display
area. - All doors (except the rear gate/trunk) are closed.
- The driver’s seatbelt is fastened.
- The electronic parking brake is not engaged (The brake system warning light
is turned off.).
- The select lever is in the position, and the paddle shift is not operated.
- The brake pedal is not depressed.
- EyeSight operation is not temporarily stopped.
Ÿ Refer to page 87.
- The road is not on a steep slope.
- The steering wheel has not been turned significantly in either direction.
- The X-mode is not turned on.
- The vehicle speed is between approximately 25 MPH (40 km/h) and 90 MPH (145 km/h).
(3) Control the accelerator pedal to reach the desired speed.
S01992S01129
S02327D