2017 SUBARU CROSSTREK audio

QUICK REFERENCE
28
QUICK REFERENCE
“SETTINGS (SETTINGS)” SCREEN
The items shown on the “SETTINGS (SETTINGS)” screen
can be set. Select
and then select SETTINGS
(SETTINGS) to display the “SETTINGS (SETTINGS)”
screen.
No. Function Page
Select to turn the screen off. -
Select to change the selected language,
operation sound, automatic screen
change settings, etc.190
Select to customize the split screen. 47
Select to specify voice settings. 196
Select to specify audio settings. 99
Select to specify phone sound, contacts,
message settings, etc.136
Select to set Bluetooth phones and
Bluetooth audio devices.181
Select to adjust the brightness, contrast,
tone and color of the screens.50

FUNCTION INDEX
34
FUNCTION INDEX
FUNCTION INDEX
XAudio
Function Page
Using the radio 60, 69
Playing an audio CD or MP3/WMA/AAC disc 78
Playing an SD*
1 card 87
Playing a USB memory 81
Playing an iPod
®84
Playing a Bluetooth device 91
Using the aha application 156
Using the AUX port 94
Using the MirrorLink
TM application 154
Using the Pandora
®*2 application 162
Using the steering wheel audio switches 96
Audio system settings 99
*1: With navigation function
*2: Pandora is available in the United States, Australia, and New Zealand.
XMap*
*: With navigation function
Displaying maps Page
Viewing the map screen 198
Displaying the current position 203
Changing the scale 204
Changing the map orientation 205
Displaying the estimated travel/arrival time to the
destination222
'LVSOD\LQJWUDI¿FLQIRUPDWLRQ206
Searching for destinations Page
Searching for the destination 208

BASIC INFORMATION BEFORE OPERATION
47
BASIC FUNCTION
2
SPLIT SCREEN OPERATION
The split screen can display multiple information screens,
such as the audio system screen and hands-free screen,
simultaneously.
The following describes screen operation for the system
with navigation function.
1. Press and hold the “AUDIO/TUNE” knob.
2. Split screen is displayed.

”When a screen is selected, the selected screen will
change to a full-screen display.
CUSTOMIZING THE SPLIT SCREEN
The display items/area on the split screen can be changed.
XFrom the split screen
1. Select .
XFrom the “SETTINGS (SETTINGS)” screen
1. Select Split Screen (Split Screen) on the “SETTINGS
6(77,1*6

53
AUDIO
3
3

BASIC OPERATION
54
BASIC OPERATION
SOME BASICS
This section describes some of the basic features of the
audio/visual system. Some information may not pertain to
your system.
Your audio/visual system works when the ignition switch is
turned to the “ACC” or “ON” position.
CAUTION
OTo prevent the battery from being discharged, do not leave
the audio/visual system on longer than necessary when the
engine is not running.
TURNING THE SYSTEM ON AND OFF
“POWER/VOLUME” knob: Press to turn the audio/visual
system on and off. The system turns on in the last mode
used. Turn this knob to adjust the volume. Note that the
voice guidance volume can be adjusted during guidance.
“AUDIO/TUNE” knob: Press to display screen buttons for
the audio/visual system.

”A function that enables automatic return to the split
screen from the audio/visual screen can be selected.

:3

BASIC OPERATION
55
AUDIO
3
SELECTING AN AUDIO SOURCE
1. Press the “AUDIO/TUNE” knob.

”The screen can also be displayed by selecting
followed by
AUDIO (AUDIO).

”If the audio control screen appears, select
Source
(Source) on the audio screen or press the “AUDIO/
TUNE” knob again.
2. Select the desired source.
NOTE
OWhen there are two pages, select or to change the page.
REORDERING THE AUDIO SOURCE
1. Display the “Select Audio Source (Select Audio Source)”
VFUHHQ
:3
2. Select Reorder (Reorder).
3. Select the desired audio source then or to
reorder.
4. Select OK (OK).

BASIC OPERATION
56
SOUND SETTINGS
The following sound quality can be adjusted.
BALANCE:
A good balance of the left and right stereo channels and of
the front and rear sound levels is also important.
Keep in mind that when listening to a stereo recording or
broadcast, changing the right/left balance will increase the
volume of 1 group of sounds while decreasing the volume of
another.
EQUALIZER:
Equalizer curves set beforehand to match sound quality can
be selected, and curves can be set to your favorite music by
adjusting them individually over low to high bands.
1. Select Sound (Sound) on the audio control screen.
2. Select the desired screen button.
No. Function
Select to adjust the sound balance between the front
and rear speakers.
Select to adjust the sound balance between the left and
right speakers.
6HOHFWWRDGMXVWWKHVRXQGTXDOLW\
:3
Select to reset the adjusted sound quality.
Select to change to sound quality appropriate for the
music (POP, ROCK, JAZZ) type.
3. Select .

BASIC OPERATION
57
AUDIO
3
ADJUSTING THE SOUND QUALITY
You can adjust the sound quality from the low band to the
high band.
QADJUSTING THE SOUND QUALITY
1. On the sound settings screen, select Adjust (Adjust)
in “EQ Settings (EQ Settings)”.
2. Select the sound band that you want to adjust.
3. Select or .

”You can also adjust to the desired level by touching
the screen.

”To reset the sound quality, select
FLAT (FLAT).
QSAVING THE SOUND QUALITY
You can save the adjusted sound quality settings.
1. Adjust the sound quality.
2. Select EQ1 (EQ1) or EQ2 (EQ2) for 2 seconds or
more.

”Values cannot be saved for
FLAT (FLAT).
QUSING A PRESET SOUND QUALITY
1. Select EQ1 (EQ1) or EQ2 (EQ2) to activate the
corresponding preset sound quality.

”To reset the sound quality, select
FLAT (FLAT).

”This function can also be used at the “EQ Settings
(EQ Settings)”.
QRESETTING THE EQ CURVE
You can return the adjusted value for the currently stored
equalizer to its initial value.
1. Select and hold FLAT (FLAT) for 2 seconds or more.

”The adjusted values for the stored
EQ1 (EQ1) and
EQ2 (EQ2) are returned to their initial values.