2017 RENAULT TWIZY Time

1.35
DISPLAYS AND INDICATORS (1/2)
Charge level 1
The gauge indicates the level of energy
remaining.
NB: Each time you switch off the igni-
tion, the remaining energy level will be
calculated.
Once you switch on the ignition again,
you will see a slight change in the level
display. The presence and operation of the display and indicators DEPENDS ON THE \
LEVEL OF EQUIPMENT AND THE COUNTRY.
Immobilisation threshold imminent
When the battery reaches less than 6%
charge, a beep repeats every 20 sec-
onds and warning light
Ṏ flashes on
and off.
Motor performance gradually de-
creases until the vehicle comes to a
stop.
Please see the information on “Towing:
in the event of energy loss” in Section 5.
Charge meter 2
Please refer to the information on the
“Charge meter” in Section 2.
Speedometer 3
In kilometres or miles per hour.
1
2
3
Reserve level
When the battery reaches approxi-
mately 12% charge, warning light
Ṏ
comes on, along with a beep.
To optimise your range, please see the
information on “Recommendations:
saving energy” in Section 2.

1.37
With the ignition switched on, the
clock is displayed on the instrument
panel.
Adjusting the time on the
instrument panel 1
– Press button 2 in quick succession,
as many times as necessary, to
obtain the time adjustment mode;
– press and hold button 2.
The hour reading flashes;
CLOCK
– repeatedly press button 2 as neces-
sary to adjust the hour;
– press and hold button 2 to confirm
the hours.
The minute display flashes;
– repeatedly press button 2 as neces-
sary to adjust the minutes;
– press and hold button 2 to confirm
the minutes.
1
2

1.40
áMain beam headlightsWith the stalk A in position
k, pull it towards you. An indicator
light on the instrument panel will come
on.
To return to the dipped headlights posi-
tion, pull stalk A towards you again.
eSwitching off the lightsReturn the stalk to its original
position. When the engine is started,
the dipped headlights stay on. They will
go out once the engine is switched off.
EXTERIOR LIGHTING AND SIGNALS (1/2)
Daytime running lights
The dipped headlights come on without
using the stalk A when the engine is
started.
uSide lights
Turn end 1 of stalk A until the
symbol is opposite mark 2.
The instrument panel lighting dims.
A
kDipped beam
headlights
Manual operation
Turn end 1 of stalk A until the symbol is
opposite mark 2.
With the ignition switched off, it is not
possible to operate the lights (to avoid
lights being used when parked).
21
A
When the vehicle is driven at
maximum permissible load (refer
to the information on «Weights» in
section 6), you must have the dipped
beam headlights adjusted, while it is
being used, by an Approved Dealer.

1.41
EXTERIOR LIGHTING AND SIGNALS (2/2)
Lights-on warning buzzerIf the stalk is not returned to its ini-
tial position
e after the ignition is
switched off, a warning beep sounds
four times to warn you.
Retroreflectors 3
Remember to check the condition of
the side retroreflectors regularly. In the
event of damage, please replace them.
3

1.42
SCREEN WASHER/WIPER
nWindscreen wiper
With the ignition on, move
stalk 1:
A park
B intermittent wiping The wipers will pause for several
seconds between sweeps.
C normal wiping speed
D fast wiping speed
A
B
C
D
1
1
Windscreen washer
With the ignition on, pull stalk 1 towards
you.
In the snow or ice, make sure that
the wiper blades are not stuck by
ice.
Keep an eye on the condition of the
blade. Replace the wiper blades
as soon as they begin to lose effi-
ciency: approximately once a year.
Check the condition of the wiper
blades. How long they last depends
on you:
– they should be kept clean: clean the blades and the windscreen
regularly with soapy water;
– do not use them when the wind- screen is dry;
– free them from the windscreen when they have not been used
for a long time.
In any event, replace them as soon
as they begin to lose efficiency: ap-
proximately once a year.
When working on the vehi-
cle, ensure that the wind-
screen wiper stalk is in po-
sition A (off).
Risk of injury.
Before any action involving
the windscreen (washing
the vehicle, de-icing, clean-
ing the windscreen, etc.)
return stalk 1 to position A (park).
Risk of injury and/or damage.

2.2
“Accessories” position ANo power-consuming device will oper-
ate when the ignition is switched off.
“On” position MThe ignition is switched on:
Start position D
Starting the engine
Turn the key to the D position and hold
it in this position until you hear a beep.
Release the key.
As soon as warning light
Ṑ stops
flashing, your vehicle is ready to drive.“Stop, steering and
handbrake lock” position St
To unlock: turn the key and the steering
wheel slightly.
To lock: remove the key and turn the
steering wheel until the steering column
locks.
To release the handbrake, please see
the information on “Handbrake” in
Section 2.
STARTING, STOPPING THE ENGINE
The vehicle cannot be started if the
charging cord is plugged in and
powered or if the charging flap is
open.
Stopping the engine
Bring the key to “Stop” position.
Warning light
Ṑ goes out.
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-suffi-
cient alone on your vehicle, even for
a short time.
They may pose a risk of injury, such
as by starting the engine or activat-
ing equipment.
Risk of serious injury.

2.9
CHARGE METER/ECO-CONSUMPTION
Eco-consumption (Éco ScorE)This function shows the driver whether
their driving style is suitable for an opti-
mum vehicle range.
To display this function, press the end
of the windscreen wiper stalk as many
times as necessary.
The squares C indicate increased
range: the more squares there are, the
more range there is remaining for the
vehicle.
Éco ScorE is calculated using the aver-
age from the last 1.8 miles (3 kilome-
tres) travelled. After the traction battery
is charged, it is calculated based on the
last 93 miles (150 kilometres).
Power recovery
B
When driving, if you lift your foot off the
accelerator pedal, the motor generates
electrical current during deceleration,
and this energy is used to recharge the
traction battery.Charge meter
The charge meter gives the driver a
real-time view of the vehicle’s remain-
ing power.
Power consumption A
The traction battery supplies the elec-
trical energy required for the motor to
move the vehicle.
BA
C

4.5
12 VOLT BATTERY (2/2)Connecting a charger to the
accessories socket
Only use a charger that is compatible
with a nominal voltage of 14.4 volts
and a current limited to 5 amps.
With the ignition switched on, plug
the power supply into the accessories
socket 7 located in the storage com-
partment 8. Please consult an authori-
sed dealer.
Recharging the 12 volt
battery
It is difficult to access the 12 volt bat-
tery. It is therefore recommended that
you attach the vehicle plug to a power
source: energy is supplied to both the
12 volt battery and the traction battery
at the same time.
Please refer to the information on
“Electric vehicle: charging” in Section 1.
Do not forget to switch off the ignition
when replacing the traction battery.
Immobilising the vehicle for an
extended period of time
Before immobilisation, you should
make sure that:
– the ignition is switched off;
– the side lights and hazard warning lights are switched off;
– the traction battery is fully charged.
After lengthy immobilisation, it is normal
to find the traction battery charge
level down. In this case, recharge it
(see “Electric vehicle: charging” in
Section 1).
Do not use booster cables
to start the vehicle.
Risk of serious injury.
8
7
Only connect accessories
with a maximum power of
65 watts. When several ac-
cessory sockets are used
at the same time, the total power of
the connected accessories must not
exceed 65 watts.
Fire hazard.