2017 Ram 5500 Chassis Cab drive shaft

CAUTION!(Continued)
damage. Tow with all four wheels either ON the
ground, or OFF the ground (using a vehicle trailer).
• Tow only in the forward direction. Towing this
vehicle backwards can cause severe damage to the
transfer case.
• Automatic transmissions must be placed in PARK
for recreational towing.
• Manual transmissions must be placed in gear (not in
Neutral) for recreational towing.
• Before recreational towing, perform the procedure
outlined under “Shifting Into NEUTRAL (N)” to be
certain that the transfer case is fully in NEUTRAL
(N). Otherwise, internal damage will result.
• Towing this vehicle in violation of the above require-
ments can cause severe transmission and/or transfer
case damage. Damage from improper towing is not
covered under the New Vehicle Limited Warranty.
• Do not disconnect the rear driveshaft because fluid
will leak from the transfer case, causing damage to
internal parts.
• Do not use a bumper-mounted clamp-on tow bar on
your vehicle. The bumper face bar will be damaged.
Shifting Into NEUTRAL (N)
Use the following procedure to prepare your vehicle for
recreational towing.
WARNING!
You or others could be injured or killed if you leave the
vehicle unattended with the transfer case in the NEU-
TRAL (N) position without first fully engaging the
parking brake. The transfer case NEUTRAL (N) posi-
tion disengages both the front and rear drive shaft
from the powertrain, and will allow the vehicle to roll,
even if the automatic transmission is in PARK (or
manual transmission is in gear). The parking brake
should always be applied when the driver is not in the
vehicle.
CAUTION!
It is necessary to follow these steps to be certain that
the transfer case is fully in NEUTRAL (N) before
recreational towing to prevent damage to internal
parts.
1. Bring the vehicle to a complete stop, with the engine running. Firmly apply the parking brake.
420 STARTING AND OPERATING

MAINTAINING YOUR VEHICLE
CONTENTS
ENGINE COMPARTMENT — 6.4L ...........447
 ONBOARD DIAGNOSTIC SYSTEM (OBD II) . . . .448
▫ Onboard Diagnostic System (OBD II)
Cybersecurity ........................ .448
▫ Loose Fuel Filler Cap Message .............449
 EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS .......................... .449
 REPLACEMENT PARTS ...................450
 DEALER SERVICE ...................... .451
 MAINTENANCE PROCEDURES .............451
▫ Engine Oil .......................... .452
▫ Engine Oil Filter ...................... .454
▫ Engine Air Cleaner Filter .................454
▫ Accessory Drive Belt Inspection ............456
▫ Maintenance-Free Battery .................457 ▫
Air Conditioner Maintenance ..............458
▫ Front Prop Shaft Lubrication — Four-Wheel Drive
Models ............................. .464
▫ Body Lubrication ..................... .465
▫ Windshield Wiper Blades .................466
▫ Adding Washer Fluid ...................469
▫ Exhaust System ....................... .469
▫ Cooling System ....................... .471
▫ Brake System ........................ .475
▫ Rear Axle And 4x4 Front Driving Axle Fluid
Level .............................. .477
▫ Transfer Case ........................ .478
▫ Automatic Transmission — If Equipped ......478
▫ Appearance Care And Protection From
Corrosion ........................... .481
7

9. Pull the tension tether outward and reinstall the glovecompartment past the travel stops by pushing in on the
glove compartment sides.
NOTE: Ensure the glove compartment door hinges and
glove compartment travel stops are fully engaged. 10. Reattach the glove compartment tension tether by
inserting the tether clip in the glove compartment and
sliding the clip away from the face of the glove
compartment door.
Front Prop Shaft Lubrication — Four-Wheel Drive
Models
Lubricate the front driveshaft grease fitting at each oil
change.
The grease fitting is located at the rear of the front
driveshaft, near the centering mechanism of double cardan
Right Side Of Glove Compartment
1 — Glove Compartment Tension Tether
2 — Glove Compartment Travel Stop
Front Drive Shaft Double Cardan Joint
464 MAINTAINING YOUR VEHICLE

Maintenance Chart
Required Maintenance
Refer to the Maintenance Schedules on the following pages
for required maintenance.
At Every Oil Change Interval As Indicated By OilChange Indicator System:
•Change oil and filter.
• Rotate the tires. Rotate at the first sign of irregular
wear, even if it occurs before the oil indicator
system turns on.
• Inspect battery and clean and tighten terminals as
required.
At Every Oil Change Interval As Indicated By Oil
Change Indicator System:
•Inspect automatic transmission fluid if equipped
with dipstick.
• Inspect brake pads, shoes, rotors, drums, hoses and
park brake.
• Inspect engine cooling system protection and hoses.
• Inspect exhaust system.
• Inspect engine air cleaner if using in dusty or
off-road conditions.
• Lube the front drive shaft fitting.
8
MAINTENANCE SCHEDULES 505