2017 Peugeot 301 fuel consumption

9
As a passenger, if you avoid connecting your
multimedia devices (film, music, video game
etc.), you will contribute towards limiting the
consumption of electrical energy, and so of
fuel.
Disconnect your portable devices before
leaving the vehicle.
Eco-driving
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2 emissions.
Optimise the use of your
gearbox
With a manual gearbox, move off gently,
change up without waiting and drive by
changing up quite soon.
With an automatic or electronic gearbox, stay
in Drive D or Auto A, according to the type
of gearbox, without pressing the accelerator
pedal heavily or suddenly.
The gear efficiency indicator invites you to
engage the most suitable gear: as soon as the
indication is displayed in the instrument panel,
follow it straight away.
For vehicles fitted with an electronic or
automatic gearbox, this indicator appears only
in manual mode.
Drive smoothly
Maintain a safe distance between vehicles,
use engine braking rather than the
brake pedal, and press the accelerator
progressively. These practices contribute
towards a reduction in fuel consumption and
CO
2 emissions and also help to reduce the
background traffic noise.
If your vehicle has cruise control, make use of
the system at speeds above 25 mph (40 km/h)
when the traffic is flowing well.
Control the use of your electrical
equipment
Before moving off, if the passenger
compartment is too warm, ventilate it by
opening the windows and air vents before
using the air conditioning.
Above 30 mph (50 km/h), close the windows
and open the air vents.
Remember to make use of equipment that can
help keep the temperature in the passenger
compartment down (window blinds, etc.). Switch off the headlamps and fog lamp when
the level of light does not require their use.
Avoid running the engine before moving off,
particularly in winter; your vehicle will warm up
much faster while driving. Switch off the air conditioning as soon as the
desired temperature is attained.
Switch off the demisting and defrosting
controls, if not automatic.
Switch off the heated seat as soon as
possible.
.
Eco-driving

10
Limit the causes of excess
consumption
Spread loads throughout the vehicle; place
the heaviest items in the bottom of the boot,
as close as possible to the rear seats.
Limit the loads carried in the vehicle and
reduce wind resistance (roof bars, roof rack,
bicycle carrier, trailer...). Preferably use a roof
box.
Remove roof bars and roof racks after use.
At the end of winter, remove snow tyres and
refit your summer tyres.
Observe the recommendations
on maintenance
Check the tyre pressures regularly, when cold,
referring to the label in the door aperture,
driver's side.
Carry out this check in particular:
-
b
efore a long journey,
-

a
t each change of season,
-

a
fter a long period out of use.
Don't forget the spare wheel and the tyres on
any trailer or caravan. Have your vehicle serviced regularly (engine
oil, oil filter, air filter, etc.) and observe the
schedule of operations recommended by the
manufacturer.
When filling the tank, do not continue after the
3
rd cut-off of the nozzle to avoid over flow.
At the wheel of your new vehicle, it is only
after the first 1,800 miles (3,000 kilometres)
that you will see the fuel consumption settle
down to a consistent average.
Eco-driving

33
Trip computer
System that gives you information on the
current journey (range, fuel consumption, ...).
Instrument panel display screen
Monochrome screen C
Display of information
F Press the button located at the end of the wiper control stalk , to display the various
trip computer data. The on-board computer
information is the following:
-


Range.
-

C
urrent fuel consumption.
-
D

istance travelled.
-
A

verage fuel consumption.
-
A

verage speed.
F

T
he next press then returns you to the
normal display.
Zero reset
F Hold the control down for more than two seconds to reset to zero the distance
travelled, the average fuel consumption
and the average speed.
1
Instruments

34
Touch screen
The information is accessible in the "Driving"
menu.
Display of information in the
touch screen
Permanent display:
F Sel ect the " Applications " menu, then " Tr i p
computer ". The current fuel consumption tab with:
-


Range.
-
T
he current instantaneous fuel
consumption.
-
T
he Stop & Start time counter,
The trip " 1" tab with:
-
D

istance travelled.
-
A

verage fuel consumption.
-

A
verage speed for the first trip.
The trip " 2" tab with:
-
D

istance travelled.
-
A

verage fuel consumption.
-

A
verage speed for the second trip.
Reset trip
The information of the trip computer isdisplayed
in tabs.
F
P
ress one of the buttons to display the
desired tab.
Temporary display in a new window:
F

P
ress the end of the wiper control lever for
access to the information and display the
different tabs. F

W
hen the desired trip is displayed, press
the reset button or on the end of the wiper
control lever.
Tr i p s " 1" and " 2" are independent and are used
identically.
Tr i p " 1" allows daily calculations to be carried
out, for example, and trip " 2" allows monthly
calculations.
Instruments

35
On-board computer, some definitions
Range
(k m)
The number of kilometres which
can be covered with the fuel
remaining in the tank. Related
to the average fuel consumption
over the last few kilometres
travelled.
This value may vary following a change in
the style of driving or the relief, resulting
in a significant change in the current fuel
consumption.
When the range falls below 20 miles (30 km),
dashes are displayed. After filling with at least
5 litres of fuel, the range is recalculated and is
displayed if it exceeds 60 miles (100 km).
If dashes are displayed continuously while
driving in place of the digits, contact a
PEUGEOT dealer or a qualified workshop.
Current fuel consumption
(l/100 km or km/l)
Calculated over the last few
seconds.
This function is only displayed from
20 mph (30 km/h).
Average fuel consumption
(l/100 km or km/l)
Calculated since the last time the
trip was reset.
Average speed
(km/h)
Calculated since the last time the
trip was reset.
Distance travelled
(k m)
Calculated since the last time the
trip was reset.
Time counter Stop & Start
If your vehicle is fitted with Stop &
Start, a time counter calculates the
time spent in STOP mode during a
j o u r n ey.
It resets to zero every time the
ignition is switched on.
(minutes / seconds or hours / minutes)
1
Instruments

58
Rear screen demist - defrost
The control button is located on the heating / ventilation or air conditioning system
control panel.
Switching on
Demisting - defrosting of the rear screen can
only function when the engine is running.F

P
ress this button to demist /
defrost the rear screen and
(depending on version) the
door mirrors. The indicator
light associated with the button
comes on. The demisting/defrosting switches off
automatically to prevent an excessive
consumption of current.
Switching off
F The front defrosting operation
can be stopped before it turns
off automatically by pressing the
button again.
The indicator light associated with the button
goes off.
Turn off the defrosting of the rear window
and the side mirrors (depending on
the version) as soon as you consider it
necessary.
Because lower energy consumption
reduces fuel consumption.
Heated lower windscreen
(Depending on the country of sale.)
In cold conditions, the heated rear window
switch also allows the lower windscreen to be
heated, so as to free the wiper blades when
frozen to the glass by frost or snow.
The function is active when the ambient
temperature is below 0°C.
Ease of use and comfort

74
Tyre under-inflation detection
System which automatically checks the
pressures of the tyres while driving.
The system monitors the pressures in the four
tyres, once the vehicle is moving.
It compares the information given by the four
wheel speed sensors with reference values,
which must be reinitialised ever y time the
tyre pressures are adjusted or a wheel
changed.
The system triggers an alert as soon as it
detects a drop in the inflation pressure of one
or more tyres.Under-inflation alert
The under-inflation detection system does
not replace the need for vigilance on the
part of the driver.
This system does not avoid the need to
check the tyre pressures (including the
spare wheel) every month as well as
before a long journey.
Driving with under-inflated tyres worsens
road-holding, lengthens braking distances,
causes premature wear of the tyres,
particularly in adverse conditions (heavy
loads, high speeds, long journeys). Driving with under-inflated tyres
increases fuel consumption.
The inflation pressures defined for your
vehicle can be found on the tyre pressure
label.
For more information on the
Identification markings , refer to the
corresponding section.
Checking tyre pressures
This check should be done when the tyres
are "cold" (vehicle stopped for 1 hour or
after a journey of less than 6 miles (10 km)
at moderate speeds).
Other wise, add 0.3 bar to the pressures
shown on the label. This warning is indicated by
continuous illumination of the light,
an audible signal and a message
displayed on the screen.
F
R
educe speed immediately, avoid
excessive steering movements and sudden
braking.
F
S
top as soon as it is safe to do so.
The loss of pressure detected does not
always cause visible bulging of the tyre.
Do not rely on a simple visual check.
F I f you have a compressor (such as the
one in the temporary puncture repair kit),
check the pressures of the four tyres when
cold. If it is not possible to make this check
immediately, drive carefully at reduced
speed.
or
F

I
n the event of a puncture, use the
temporary puncture repair kit or the spare
wheel (depending on equipment).
The warning remains active until the
system is reinitialised.
Safety

108
Automated mode
F Select position A.
You can change mode at any time by
moving the gear selector from A to M or
the other way round.
Moving vehicle, never select the neutral N .
The instrument cluster displays
AUTO
along with the gear engaged.
The gearbox is then operating in auto-active
mode, without any action on the part of the
driver. It continuously selects the most suitable
gear for adapted to the following parameters:
-
o

ptimisation fuel consumption,
-

t
he style of driving,
-

r
oad conditions,
-

v
ehicle load.
For optimum acceleration, when overtaking
another vehicle for example, press the
accelerator pedal fully down, beyond the point
of resistance.
Manual mode
F Select position M .
Moving vehicle, never select the neutral N .
You can change mode at any time by
moving the gear selector from M to A or
the other way round. The gears engaged appear in turn in
the instrument cluster.
The shift requests are taken into account only if
the engine speed allows.
It is not necessary to release the accelerator
when changing gear.
When braking or slowing down, the gearbox
changes down automatically to allow the
vehicle to accelerate in the correct gear.
Under full acceleration, unless the engine is
close to its maximum speed, gear upshift will
only take place when the driver operates the
gear selector.
Reverse gear
To engage reverse gear, the vehicle must be
immobilised with your foot on the brake pedal.
F
Sel
ect position R .
There is an audible signal upon
engagement of reverse.
At low speed, if reverse gear is requested,
the N indicator flashes and the gearbox goes
into neutral automatically.
To engage reverse, put the gear selector into
position N , then to position R .
Driving