2017 NISSAN ROGUE HYBRID tire size

B. You must pay for taxes and any additional servicesyou order at the time of adjustment plus any addi-
tional service that may be unique to your application,
e.g. Tire Pressure Monitoring System.
C. You must submit your claim on an approved claim form supplied by an authorized Goodyear or Dunlop
service facility. The form must be filled out com-
pletely and signed, where you the owner or your
authorized agent presented the tire for adjustment.
SAFETY WARNINGS
Property damage, serious injury or death may result
from:
TIRE FAILURE DUE TO UNDERINFLATION/
OVERLOADING / MISAPPLICATION.
Follow the vehicle owner’s manual or tire placard in
vehicle.
TIRE FAILURE DUE TO IMPACT DAMAGE /
IMPROPER MAINTENANCE.
Tires should be inspected regularly by a qualified
technician for signs of damage, such as punctures or
impacts.
TIRE FAILURE DUE TO IMPROPER REPAIRS.
See Rubber Manufacturer’s Association (RMA) es-
tablished repair procedures at www.rma.org and/or
go to www.goodyear.com for information on proper
repair procedures.
EXPLOSION OF TIRE/RIM ASSEMBLY DUE
TO IMPROPER MOUNTING.
Only specially-trained persons should mount tires.
When mounting tires, use safety cage and clip-on
extension air hose to inflate.
FAILURE TO MOUNT RADIAL TIRES ON AP-
PROVED RIMS.
FAILURE TO DEFLATE SINGLE OR DUAL AS-
SEMBLIES COMPLETELY BEFORE DE-
MOUNTING.
TIRE SPINNING.
On slippery surfaces such as snow, mud, ice, etc.,
do not spin tires in excess of 35 mph (55 kph) , as
indicated on the speedometer.
EXCESSIVE WHEEL SPINNING.
This can also result in tire disintegration or axle
failure.
WARNING: Vehicle handling, traction, ride comfort and
other performance parameters may be significantly af-
fected by a change in tire size or type. Before replacing
tires, always consult and follow the vehicle Owner’s
Manual because some vehicle manufacturers prohibit
changing tire size. When selecting tires that are differ-
ent from the original equipment size make certain: (1)
The tires have adequate load carrying capacity based
on the vehicle placard, (2) The tires have sufficient
inflation pressure to carry the load and (3) There is
proper clearance with no interference points between
the tire and vehicle. The consumer must be aware to
always drive safely and obey all traffic laws. Avoid
sudden, sharp turns or lane changes. Failure to follow
any of these warnings may result in loss of control of the
vehicle, leading to an accident and serious injury or
death.
TIRE CARE AND MAINTENANCE GUIDE
The easiest way to help ensure satisfactory mileage and
performance from your Goodyear or Dunlop tires is to
give them a simple but frequent (at least monthly) in-
spection for proper inflation, even treadwear, and the
presence of any damage.
DO MAINTAIN PROPER INFLATION
PRESSURE IN YOUR TIRES
Proper inflation pressure is necessary for optimum tire
performance, safety and fuel economy. Check inflation
pressures at least once a month and before long trips.
Use an accurate tire pressure gauge. Always check
pressures when the tires are cold (when the vehicle has
been driven less than one mile) . If you must check
inflation when the tires are hot, add 4 psi (27 kPa) to the
recommended cold inflation pressure. It is difficult to tell
just by looking at radial tires whether they are underin-
flated.*
Furthermore, when operating a vehicle equipped with
radial tires, it is difficult to notice when a tire has gone
flat or nearly flat since the “feel” of the vehicle does not
change significantly.
*Evidence of air loss or repeated underinflation
always requires expert inspection to determine
the source of leakage and tire removal to deter-
mine repairability. To avoid injury, NEVER attempt to
reinflate a tire that has been run severely underinflated.
Progressive air loss may result from punctures, cuts,
curbing, impacts or partial bead unseating. Some fit-
ment causes for air loss are (1) incomplete bead seat-
ing, (2) bead tearing caused by a machine tool due to
insufficient lubrication or improper adjustment, (3) leak-
ing valve core or rubber valve components should be
replaced when problems are detected and whenever
tires are replaced.
(Continued on next page)
26 GOODYEAR/DUNLOP TIRE LIMITED WARRANTY

The Convenience (Temporary) Spare weighs less than a
standard tire so it’s easier to handle. It also helps reduce
the total car weight which contributes to fuel economy.
The wheels used with the Convenience (Temporary)
Spare are specifically designed for use with high pres-
sure spares and should never be used with any other
type tire.
DON’T ATTEMPT TO MOUNT YOUR
OWN TIRES
Serious injury or Death may result from explosion of tire/
rim assembly due to improper mounting procedures.
Follow tire manufacturer’s instructions and match tire
diameter to rim diameter. Mount light truck radials on
rims approved for radial service. Do not apply bead
sealer. This can inhibit bead seating. Lubricate beads
and tire rim (including tube or flap) contact surfaces.
Lock assembly on mounting machine or place in safety
cage. STAND BACK and never exceed 40 psi to seat
beads. Never use a volatile substance or a rubber
“donut” (also known as a bead expander or “O-Ring”) to
aid bead seating. Only specially-trained persons should
mount tires.
DON’T MIX TIRES OF DIFFERENT
SIZES AND TYPES ON THE SAME
AXLE
For optimum handling and control, Goodyear and Dun-
lop recommend fitment of four (4) tires of the same type
and size unless otherwise specified by the vehicle
manufacturer.
WARNING: Before you replace your tires, always con-
sult the vehicle Owner’s Manual and follow the vehicle
manufacturer’s replacement tire recommendations. Ve-hicle handling may be significantly affected by a change
in tire size or type. When selecting tires that are different
than the Original Equipment size, see a professional
installer in order to make certain that proper clearance,
load carrying capacity and inflation pressure is selected.
Never exceed the maximum load capacity and inflation
pressure listed on the sidewall of the tire. Always drive
safely and obey all traffic laws. Avoid sudden, sharp
turns or lane changes. Failure to follow this warning may
result in loss of control of the vehicle, leading to an
accident and serious injury or death.
When replacing tires, you must maintain the outside
diameter and load carrying capacity of the Original
Equipment tire. Inflation pressure may need to be ad-
justed to avoid overloading the tire. Consult the Tire &
Rim Association Load and Inflation Tables, ETRTO or
JATMA standards for correct load and inflation informa-
tion.
NEVER FIT TIRES TO A VEHICLE THAT
HAVE LESS LOAD CARRYING
CAPACITY THAN AS REQUIRED BY
THE ORIGINAL EQUIPMENT
MANUFACTURER
Examples: Many vehicles, such as large passenger
vans, require Load Range E tires as designated by the
vehicle manufacturer. Fitment of a tire, such as a Load
Range D, with less carrying capacity is not allowed.
In other cases, tires of the same size may carry different
load indexes in the service description. You must make
certain the replacement tires fitted to the vehicle have a
load carrying capacity equal to or greater than what the
Original Equipment manufacturer specifies.NOTE:
Goodyear manufactured and/or marketed
European-Metric passenger tires and P-Metric
passenger tires are interchangeable as long as
they have the same section width, same aspect
ratio, same rim diameter. Caution: Never substi-
tute a “Standard Load” (SL) tire for an Extra Load
(XL) tire. If the vehicle was originally equipped
with “Extra Load” (XL) tires, replace those tires
with similar sized XL tires.
FOLLOW THESE ADDITIONAL
GUIDELINES
When installing only two tires, fit the tires with the
deepest tread depth on the rear axle. If radials and
non-radials must be fitted to the same vehicle, fit radials
on rear axle. Never mix radials and non-radials on the
same axle. When fitting snow tires or all-season tires to
performance vehicles, always fit in sets of four. It is not
recommended to fit tires with different speed ratings. If
tires with different speed ratings are installed on a
vehicle, they should be installed with like pairs on the
same axle. The speed capability of the vehicle will
become limited to that of the lowest speed rated tires.
Use of lift kits with some vehicle/tire combinations can
cause instability. When changing tire sizes, always con-
sult Dealer for optimum rim width and carefully checkvehicle/tire clearances.
(Continued on next page)
28
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY

OWNER’S OBLIGATIONS
At least monthly, the vehicle owner(s) should check the
tires’ air pressure with a gauge and inflate to the recom-
mended cold air pressure level listed on the driver’s
door placard. Do not rely on car servicers to perform the
checks. The tires should be rotated at least every
8,000km (5,000 miles) or earlier if uneven wear is
occurring, and proof of maintenance records should be
kept. The owner(s) should have the tires rebalanced if
vibration is experienced, and the vehicle’s alignment
should be checked if uneven or rapid wear is occurring,
or when suggested by the vehicle’s manufacturer.
All warranty claims must be presented to an authorized
Falken dealer or participating car dealership. The own-
er(s) must present any supporting maintenance records
and documentation necessary to help determine if the
tire(s) in question are deemed covered by the limited
warranty or not.
LEGAL RIGHTS
All implied warranties, including warranties of mer-
chantability and fitness for a particular purpose shall be
limited in duration to the above period. To the extent
permitted by law, Falken Tire Corporation shall not be
responsible for incidental or consequential damages,
such as loss of use of the tire or the vehicle on which it
is used, inconvenience, or commercial loss, some states
do not allow limitations on how long an implied warranty
lasts, or the exclusion or limitation of incidental or con-
sequential damages, so the above limitations or exclu-sions may not apply to you. This warranty gives you
specific legal rights and you may also have other rights,
which vary from state to state. This is the only express
warranty applicable to Falken brand tires and super-
sedes the terms of any previous warranty. Falken neither
assumes nor authorizes anyone to make or assume for it
any other warranty.
TIRE CARE AND RECOMMENDATIONS
PROPER INFLATION and FUEL ECONOMY*
Ensure maximum performance and a long life from your
tires by checking the air pressures at least once a month
and set them to the vehicle manufacturer’s recom-
mended pressure(s) listed on the vehicle’s tire placard
or in your owner’s manual. Always check and adjust your
air pressure when your tires are cold, preferably first
thing in the morning before driving. Never release air
pressure from tires when they are hot. Wait until the tires
cool down and recheck, adding air or releasing as
required. Falken endorses the use of nitrogen in your
tires because it helps your tires maintain optimal pres-
sure for longer periods of time and reduces the amount
of moisture inside of the tire and wheel assembly.
TIRE INFLATION PRESSURE
Tires need to be properly inflated to effectively operate
and perform as intended. Tires carry the weight of the
vehicle, passengers, and cargo as well as bear the
forces of braking, accelerating, and turning. The vehicle
manufacturer sets the inflation pressures for the original
equipment tires that are on your vehicle.Driving with improperly inflated tires is dangerous. An
under inflated tire will generate excessive heat build-up
that will cause damage to the internal structure and
inner liner of the tire. Besides tire damage, improper tire
inflation pressures can also affect your vehicle’s ride
and handling, tire tread wear, and fuel economy. It is
recommended to always keep all of your tires, including
the spare, at the vehicle manufacturer’s recommended
inflation pressures and be sure to check the air pressure
monthly and before going on long road trips or carrying
extra weight in your vehicle.
Your vehicle’s tire placard and/or owner’s manual will
list the cold inflation pressure(s) for your vehicle’s origi-
nal equipment tires, including the spare. The placard
can be found on the driver’s side door or door jamb area.
If you have questions about understanding your vehi-
cle’s tire placard, please refer to your owner’s manual or
ask a qualified tire service professional.
●For detailed information on TIRE INFLATION PRES-
SURE please visit www.Falkentire.com
(Continued on next page)
* Some plus size applications may require different air pressure(s) than what is listed on your vehicle’s placard or owner’s manual. In this case, please consult your tire dealer or Falken Tire
for proper inflation pressure(s) .
36 FALKEN TIRE LIMITED WARRANTY

TIRE MIX USAGE
WARNINGSAFETY WARNING
Never mix tires of different size or con-
struction and/or type on any axle. (Except
for temporary use as a spare tire.) Always
refer to the vehicle’s owner manual for
proper tire fitments.
TIRE SPEED RATINGS
Falken recommends replacing your tire(s) with the same
speed rating as the original tires equipped on your
vehicle.
It is okay to use a lower speed rated tire when using
winter tires. However, speeds should be reduced to
match the tires new “maximum” speed capability.
Any tire that is repaired, damaged, abused, altered from
its original state or retreaded voids the speed rating on
that particular tire and should be considered a non-
speed rated tire.
WARNING SAFETY WARNING
Falken does not recommend the use of
mixing different speed ratings on a ve-
hicle. This can cause poor handling and
unpredictable steering.
HIGH PERFORMANCE, LOW ASPECT RATIO
TIRES
Various new vehicles come equipped with high perfor-
mance and/or low aspect ratio tires from the factory.
These tires generally provide increased vehicle handling
characteristics, but may also have engineering perfor-
mance trade-offs related with their designs. Low aspect
ratio tires have reduced sidewall heights and may be
more vulnerable to damage from road hazards, pot-
holes, and other objects, like curbs. Your vehicle’s
wheels are susceptible to these same dangers as well.
Some vehicles may be originally equipped with high
performance tires that are designed for warmer weather
use reducing traction in colder, winter weather condi-
tions. High performance tires also pose the possibility of
wearing more quickly, giving a stiffer ride, and produc-
ing louder noise than standard all-season tires during
operation. Refer to your vehicle owner’s manual, tire
information placard, or qualified tire service professional
for more information about these kinds of tires.
WINTER TIRES
Falken recommends all four tires be replaced when
replacing your original equipment tires and installing
winter tires for the winter months.
WARNING SAFETY WARNING
Never use just two winter tires. It could
lead to adverse handling, loss of control,
which could cause serious injury or death.
STORING YOUR TIRES
When storing your tires for any extended period of time, be
sure to thoroughly clean your tires with a tire brush, soap,
and water to remove any dirt, salt, and brake dust from the
tires. If you are storing your tires still mounted on the
wheels, use a wheel brush and approved wheel cleaner to
clean your wheels. Then dry the wheels and tires with a
towel and allow them to fully dry. DO NOT apply any tire
dressings while storing your tires. Tire compounds are
made to resist weather cracking and ozone damage. Place
each clean and dry tire in an airtight plastic bag and seal the
bag with tape to help reduce oil evaporation. Store your
tires out of direct sunlight and somewhere that is well
shielded from the elements, like a climate-controlled room
or dry basement. Storing the tires in a garage or shed
usually exposes the tires to a wide range of temperatures
as well as precipitation and humidity. Keep the tires away
from sources that emit ozone like electric motors that use
contact brushes, furnaces, sump pumps, etc. Although
tires will still age regardless of how they are stored, these
precautions will help slow the aging process and reduce
the damage to your tires.
WARNING SAFETY WARNING
Operating your vehicle in excess of the
posted speed limit or the maximum speed
allotted by driving conditions has the po-
tential to be dangerous. Higher driving
speeds create excessive heat buildup in a
tire, leading to a possible tire failure.
(Continued on next page)
38 FALKEN TIRE LIMITED WARRANTY

TIRE SPINNING
WARNINGSAFETY WARNING
Spinning a tire to get a stuck vehicle out of
mud, ice, snow, sand, or wet grass can be
potentially dangerous. A spinning tire at a
speedometer reading above 55 km/h
(35 mph) can be capable of disintegrating
a tire with explosive force. In some circum-
stances, a tire may be spinning at twice
the speed displayed on the speedometer.
This can cause serious injury or death to
you, a passenger, or bystander. Never spin
a tire above 55 km/h (35 mph) .
UNDERSTANDING YOUR TIRES
TIRE SPEED SYMBOLS
Tires that are speed-rated are identified by the following
letter symbols: Q, S, T, U, H, V, W, Y, (Y) , or (ZR) . The
Speed Rating’s Symbol can be found as a part of the tire
size designation (ex: 215/65HR16) or after the load
index immediately following the tire size designation (ex:
215/65R16 97H) . The Speed Rating’s Symbol indi-
cates the maximum speed that a tire can handle when
properly inflated and loaded.
●For detailed information on UNDERSTANDING
YOUR TIRES please visit www.Falkentire.com DATE OF TIRE MANUFACTURE
The date that a tire was manufactured can be deter-
mined by examining the last 4 digits of the 12 digit DOT
serial code, which is found on at least one sidewall of a
tire. For tires that were produced after the year 2000,
the last 4 digits of the serial code will identify the week
and the year that the tire was manufactured. If the last 4
digits in the DOT serial code were to read “3013” it
would mean that the tire was manufactured the 30th
week of 2013. If you are uncertain, check with a quali-
fied tire service professional to be sure.
DOT Symbol and DOT Serial Code
The “DOT” symbol claims that the tire conforms to all
applicable US Department of Transportation motor ve-
hicle safety standards for tires. The identification/serial
number follows the “DOT” symbol. Here is an example
of a DOT serial code:
DOT R8 ER DMNR 30 13
(A) (B) (C) (D) (E) (F)
A. DOT Symbol
B. Manufacturer Plant Code
C. Tire Size Code
D. Tire Manufacturer’s Code
E. Week of Production (01–52)
F. Year of Production (the last two digits of the year)
TIRE SIDEWALL LABELING
●For detailed information on TIRE SIDEWALL LABEL-
ING please visit www.Falkentire.com MAX LOAD AND INFLATION
The maximum load and inflation pressure is marked on
the tire sidewall in English and metric units.
PLY COMPOSITION AND MATERIALS
The number of plies and their generic composition of
cord materials in the sidewall and tread areas can be
found on at least one sidewall of a tire.
RADIAL MARKING
A radial ply tire will have the word “radial” marked on at
least one sidewall. An “R” found in the tire size marking
also refers to the tire being a radial ply tire.
UNIFORM TIRE QUALITY GRADING SYSTEM
(UTQG)
The Uniform Tire Quality Grading Standards (UTQG)
were created to help you make an informed decision
when purchasing passenger car tires by providing rela-
tive information about a tire’s tread wear, traction, and
temperature characteristics. Here is a breakdown of the
different categories that the UTQG grades:
●TREAD WEAR
The tread wear grade is a comparative rating based on
the wear rate of the tire when tested under controlled
conditions on a specified government test course. For
example, a tire graded 150would wear one and a half
(1 1/2) times as well on the government course as a tire
graded 100. The relative performance of tires depends
upon the actual conditions of their use, however, and
may depart significantly from the norm due to variations
in driving habits, service practices, and differences in
road characteristics and climate.
(Continued on next page)
FALKEN TIRE LIMITED WARRANTY 39

H. Tire with weather cracking which was purchasedmore than four years prior to presentation for adjust-
ment.
●GENERAL EXCLUSIONS
I. No Hankook Tire employee, retailer or dealer has the authority to make any warranty, representation, prom-
ise or agreement on behalf of Hankook Tire except as
stated in this policy.
J. Tires used in racing related activities or competitive events are not covered by this warranty.
K. Limitation of remedy: to the extent permitted by law, HANKOOK disclaims liability for all consequential
and incidental damages. Some provinces and states
do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation
or exclusion may not apply to you. This warranty
gives you specific legal rights, and you may also
have the rights which vary from province to province
in Canada, and from state to state in the U.S.A.
3. HANKOOK’S OBLIGATIONS
Replacement qualifying under this warranty will be
made by a participating Hankook Dealer or a participat-
ing Car Dealer.
4. OWNER’S OBLIGATIONS
A. You must present the tire to a participating Hankook Dealer or a participating Car Dealer.
B. For free replacement, a proof of purchase date such as car dealer invoice should be presented.
C. No claim will be recognized unless submitted on a Hankook claim form completely filled out and signed
by the owner or a participating Hankook Dealer or
Car Dealer.
WARNING FOR YOUR SAFETY
●TIRE DEMOUNTING AND MOUNTING
Improper tire mounting and inflation procedures may
cause tire beads to break with explosive force during
installation of the tire on the rim, causing personal
injury and property damage. Follow the Rubber
Manufacturers Association installation and safety
procedure for mounting and inflating tires. Tire and
rim must match in size. Rim parts must match by
manufacturer’s design. Clean rim. Lubricate rim and
beads. Do not exceed the maximum recommended
pressure to seat beads on rim. Use remote control
inflation equipment and inflation cage.
NOTE:
Never inflate over 40 psi to seat beads. Mount
radial ply tires only on rims designated by wheel
manufacturer as suitable for radial tire. Only spe-
cially trained persons shall mount tires.
●AIR PRESSURE
Check the pressure in your tires, including your
spare, at least monthly, and always before and during
extended driving. Check tires cold (at least 3 hours
after the vehicle has been stopped and before it is
driven more than 1.6 kilometers or 1 mile) . Do not
reduce pressure when tires are hot, use an accurate
air pressure gauge to check pressure and maintain it
at the level recommended on the vehicle tire placard
or in the Owner’s Manual. Underinflation produces
extreme flexing of sidewalls and builds up heat to the
point that premature tire failure may occur. Overin-
flation can cause the tires to be more susceptible to
impact damage. Cold tire pressures, however,
should never be higher than the limit molded on the
sidewall.
●LOAD LIMITS
Never exceed the load-carrying limits molded onto
the sidewall of your tires or the maximum vehicle load
limit as shown on the vehicle tire placard, whichever
is less. Overloading builds up excessive heat in the
tire and leads to early and/or sudden failure.
●HAZARDS
Avoid running over objects (e.g., chuckholes, rocks,
curbs, metal, glass, etc.) which may possibly cause
internal tire damage. Continued use of a tire that has
suffered internal damage (which may not be exter-
nally visible) can lead to dangerous tire failure. De-
termination of suspected internal damage requires
demounting the tire from its rim and examination by
trained tire personnel.
(Continued on next page)
42 HANKOOK TIRE LIMITED WARRANTY

●WORN TIRES
Never drive on worn tires. Tires should be replaced
by trained personnel when 2/32nds inch (1.6mm) of
tread depth remain, as indicated by treadwear indi-
cators molded into the tread grooves. Use of worn-
out tires (less than 2/32nds of an inch remaining
tread depth) increases the probability of tire failure.
In most states, it is illegal to drive with less than
2/32nds of an inch of remaining tread depth.
●SPEED LIMITS
Operating your vehicle in excess of lawful speed
limits or the maximum speeds justified by driving
conditions can be dangerous. Excessive speed cre-
ates heat buildup in a tire, leading to possible tire
failure.
●SPEED-RATED TIRES
Speed-rated tires are identified by letters S, T, H, V,
W, or Z as either part of the size designation (e.g.,
HR) , or part of the service description adjacent to the
size designation (e.g., 94H) and indicates the maxi-
mum speed capability of the tire when properly
loaded and inflated. However, even when properly
loaded and inflated, driving for prolonged periods at
high speeds can cause tire damage and possible tire
failure which could lead to an accident. Original
equipment speed-rated tires must be replaced with
tires of the same or higher speed rating if the speed
capability of the vehicle is to be maintained. Consult
your Hankook dealer for the tires best suited to your
vehicle driving habit. Repairing of speed-rated tires
must be done in accordance with RMA repair pro-
cedures and is limited to one 1/4 diameter repair in
the tread area.
●TIRE ROTATION
Rotate your tires for longer tire life. Front and rear
tires perform different jobs and can wear differently.
Consult your vehicle Owner’s Manual for mileage
recommendations and rotation patterns.
●ADDITIONAL SAFETY INFORMATION FOR TEM-
PORARY TIRE
A. Air pressure. Check inflation pressure as soon as practical after
installation and inflate to 60 psi. The tire pressure
should be checked monthly and maintained at
60 psi while the tire is stored or in service.
B. Vehicle restriction. The temporary spare tire was specifically designed
for your car and should not be used on any other
vehicle.
C. Other restrictions. The temporary spare tire should not be used with
other wheels, nor should standard tires, snow tires,
wheel covers, or trim rings be used with the tempo-
rary spare wheel. If such use is attempted, damage
to these items or other vehicle components may
occur.
TIRE SERVICE ASSISTANCE OR
INFORMATION
When you have tire problems, Hankook provides ser-
vice and assistance.
Any time you see damage to your tires, contact your
local Hankook Tire Dealer.
If no local dealer is available around you, dial Hankook
Toll Free Service Number so that you can get informa-
tion on where and how service is rendered to you. FOR SERVICE ASSISTANCE OR INFORMATION
U.S.A.
CORPORATE HEADQUARTERS
1450 Valley Road, Wayne, New Jersey 07470
973-633-9000 Toll Free 877-740-7000
WEST REGIONAL OFFICE
11555 Arrow Route, Suite 105, Rancho Cucamonga,
CA 91730
909-481-9800 Toll Free 800-426-8252
CANADA
CORPORATE HEADQUARTERS
30 Resolution Dr., Brampton, Ontario L6W 0A3
905-463-9802 Toll Free 800-843-7709
HANKOOK TIRE LIMITED WARRANTY
43

J. No Mileage Warranty for Original tires.
●GENERAL EXCLUSIONS
K. No Kumho Tire employee, retailer or dealer has the authority to make any warranty, representation,
promise or agreement on behalf of Kumho Tire ex-
cept as stated in this policy.
L. Tires used in racing related activities or competitive events are not covered by this warranty.
M. Limitation of remedy: to the extent permitted by law, Kumho disclaims liability for all consequential and
incidental damages. Some provinces and states do
not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have the
rights which vary from province to province in
Canada, and from state to state in the U.S.A.
3. KUMHO OBLIGATIONS
Replacement qualifying under this warranty will be
made by a participating Kumho Dealer or a participating
Car Dealer.
4. OWNER’S OBLIGATIONS
A. You must present the tire to a participating Kumho
Dealer or a participating Car Dealer.
B. For free replacement, a proof of purchase date such as car dealer invoice should be presented.
C. No claim will be recognized unless submitted on a Kumho claim form completely filled out and signed
by the owner or a participating Kumho Dealer or Car
Dealer.
WARNING FOR YOUR SAFETY
●TIRE DEMOUNTING AND MOUNTING
Improper tire mounting and inflation procedures may
cause tire beads to break with explosive force during
installation of the tire on the rim, causing personal
injury and property damage. Follow the Rubber
Manufacturers Association installation and safety
procedure for mounting and inflating tires. Tire and
rim must match in size. Rim parts must match by
manufacturer’s design. Clean rim. Lubricate rim and
beads. Do not exceed the maximum recommended
pressure to seat beads on rim. Use remote control
inflation equipment and inflation cage. NOTE:
Never inflate over 40 psi to seat beads. Mount
radial ply tires only on rims designated by wheel
manufacturer as suitable for radial tire. Only spe-
cially trained persons shall mount tires.
●AIR PRESSURE
Check the pressure in your tires, including your
spare, at least monthly, and always before and during
extended driving, when tires cold (at least 3 hours
after the vehicle has been stopped and before it is
driven more than 1 mile / 1.6 kilometers) . Do not
reduce pressure when tires are hot, use an accurate
air pressure gauge to check pressure and maintain it
at the level recommended on the vehicle tire placard
or in the Owner’s Manual. Underinflation produces
extreme flexing of sidewalls and builds up heat to the
point that premature tire failure may occur. Overin-
flation can cause the tires ‘to be more susceptible to
impact damage. Cold tire pressures,” however,
should never be higher than the limit molded on the
sidewall.
●LOAD LIMITS
Never exceed the load-carrying limits molded onto
the sidewall of your tires or the maximum vehicle load
limit as shown on the vehicle tire placard, whichever
is less. Overloading builds up excessive heat in the
tire and leads to early and/or sudden failure.
(Continued on next page)
KUMHO TIRE LIMITED WARRANTY 45