2017 NISSAN PULSAR washer


> (GLW   0RGHO &$@
8-4
Mainten anceanddo-it-yo urself
Coolant level*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thecoolant levelwhen thecoolant iscold. Make
sure thatthecoolant levelisbetween theªMAXº and
ªMINº linesonthe reservoir.
Engine drivebelt(s)*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Make surethatdrive belt(s) is/arenotfrayed, worn,
cracked oroily .
Engine oillevel*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thelevel afterparking thevehicle (onalevel
ground) andturning offthe engine.
Fluid leaks:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check underthevehicle forfuel, oil,water orother fluid
leaks afterthevehicle hasbeen parked forawhile.
W ater dripping fromtheairconditioner afteruseis
normal. Ifyou should noticeanyleaks oriffuel fumes
are evident, checkforcause andhave itcorrected
immediately .
Windshield washerfluid*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatthere isadequate fluidinthe reservoir.
MAINTENANCE PRECAUTIONS
GUID-E46 9E0D9-6CF F-4A9B-8459-D2B589DFA455
When performing anyinspection ormaintenance work
on your vehicle, alwaystakecare toprevent serious
accidental injurytoyourself ordamage tothe vehicle.
The following aregeneral precautions whichshould be
closely observed.
WARNING:
. Park thevehicle onalevel surface, applythe
parking brakesecurely andblock thewheels
to prevent thevehicle frommoving. Move
the shift lever tothe ªPº(Park) position (CVT
model) orthe shift lever tothe ªNº(Neutral)
position (MTmodel) . .
Besure theignition switchisin the ªOFFº or
ªLOCKº position whenperforming anyparts
replacement orrepairs.
. Do not work under thehood while the
engine ishot. Always turnoffthe engine
and wait until itcools down.
. Ifyou must workwiththeengine running,
keep yourhands, clothing, hairandtools
away frommoving fans,belts andanyother
moving parts.
. Itis advisable tosecure orremove anyloose
clothing andanyjewelry, suchasrings,
watches, etc.before working onyour vehi-
cle.
. Ifyou must runtheengine inan enclosed
space suchasagarage, besure there is
proper ventilation forexhaust gasesto
escape.
. Never getunder thevehicle whileitis
supported byajack.
. Keep smoking materials, flameandsparks
away fromfuelandthebattery.
. Never connect ordisconnect eitherthe
battery orany transistorized component
connector whiletheignition switchisin the
ªONº position.
. Ongasoline enginemodels withtheMulti-
port Fuel Injection (MFI)system, thefuel
filter andfuel lines should beserviced bya
NISSAN dealerbecause thefuel lines are
under highpressure evenwhen theengine is
turned off.
. Your vehicle isequipped withanautomatic
engine cooling fan.Itmay come onatany
time without warning, evenifthe ignition switch
isin the ªOFFº position andthe
engine isnot running. To avoid injury, always
disconnect thenegative batterycablebefore
working nearthefan.
. Always weareyeprotection wheneveryou
work onyour vehicle.
. Never leavetheengine ortransmission
related component harnessconnector dis-
connected whiletheignition switchisin the
ªONº position.
. Avoid directcontact withused engine oiland
coolant. Improperly disposedengineoil,
engine coolant, and/orothervehicle fluids
can hurt theenvironment. Alwaysconform to
local regulations fordisposal ofvehicle
fluids.
This ª8.Maintenance anddo-it-yourselfº section
provides instructions regardingonlythose itemswhich
are relatively easyforanowner toperform.
Y ou should beaware thatincomplete orimproper
servicing mayresult inoperating difficulties orex-
cessive emissions, andcould affect yourwarranty
coverage. Ifin doubt aboutanyservicing, haveit
done byaNISSAN dealer.
&RQGLWLRQ


> (GLW   0RGHO &$@
GUID-66B21 62B-2CD7-470F-9DAD-BD99AF54AF2C
MRA8DE ENGINEMODEL
GUID-EF68A5 F3-BA43-45B8-853E-9 1FCC2309E B6
JVC0363X
1. Brake andclutch* fluidreservoir
Ð Right-Hand Drive(RHD) models
2. Engine oilfiller cap
3. Brake fluidreservoir
Ð Left-Hand Drive(LHD) models
4. Aircleaner
5. Battery
Ð Jump starting 6.
Window washerfluidreservoir
7. Engine drivebeltlocation
8. Engine oildipstick
9. Radiator cap
Ð Vehicle overheat
10. Engine coolant reservoir
11. Fuse/fusible linkholders
*: For Manual Transmission (MT)models
Maintenan ceand do-it-you rself
8-5
ENGINE
COMPARTMENT CHECK
LOCA TIONS
&RQGLWLRQ


> (GLW   0RGHO &$@
8-6
Mainten anceanddo-it-yo urself
MR16DD TENGINE MODEL
GUID-934 CC1DB-4294 -4799-AEA9-ED2B57AE3 33C
JVM0262X
1. Brake andclutch* fluidreservoir
2. Engine oilfiller cap
3. Radiator cap
Ð Vehicle overheat
4. Aircleaner
5. Window washerfluidreservoir
6. Engine drivebeltlocation
7. Engine oildipstick 8.
Engine coolant reservoir
9. Fuse/fusible linkholder
10. Battery
Ð Jump starting
*: For Manual Transmission (MT)model
&RQGLWLRQ


> (GLW   0RGHO &$@
HR16DE ENGINEMODEL
GUID-C9ABE EC8-90E9-4A9F-9977 -AA38DC1C1 F0A
JVC0364X
1. Brake andclutch* fluidreservoir
Ð Right-Hand Drive(RHD) models
2. Engine oilfiller cap
3. Brake andclutch* fluidreservoir
Ð Left-Hand Drive(LHD) models
4. Aircleaner
5. Battery
Ð Jump starting 6.
Window washerfluidreservoir
7. Engine drivebeltlocation
8. Engine oildipstick
9. Radiator cap
Ð Vehicle overheat
10. Engine coolant reservoir
11. Fuse/fusible linkholders
*: For Manual Transmission (MT)models
GUID-431 BB6E1-F915 -4C1F-8B9B-5A574742 5D98
WARNING:
. Never remove theradiator orcoolant reser-
voir capwhen theengine ishot. Serious
burns couldbecaused byhigh-pressure
fluid escaping fromtheradiator. Waituntil
the engine andradiator cooldown.
. Engine coolant ispoisonous andshould be
stored carefully inmarked containers outof
the reach ofchildren.
. Ifthe engine wasstopped soonwhen the
engine ishot, thecooling fanmay operate
for approximately 10minutes afterthe
engine wasstopped tocool thecomponents
in the engine compartment. Whenthecool-
ing fan isoperating, besure thathands or
other items donot getcaught init(for
MR16DDT engine).
The engine cooling systemisfilled atthe factory witha
high-quality ,year-round, anti-freezecoolantsolution.
The anti-freeze solutioncontains rustandcorrosion
inhibitors, thereforeadditional coolingsystemadditives
are not necessary .
CAUTION:
. Never useanycooling systemadditives such
as radiator sealer.Additives mayclog the
cooling systemandcause damage tothe
engine, transmission and/orcooling system.
. When adding orreplacing coolant,besure
to use only Genuine NISSANEngineCoolant
or equivalent inits quality withtheproper
mixture ratio.Examples ofthe mixture ratio
of coolant andwater areshown inthe
following table:
Maintenan ceand do-it-you rself
8-7
ENGINE
COOLING SY STEM
&RQGLWLRQ


> (GLW   0RGHO &$@
8-10
Maintenance anddo-it-yours elf
Engine oiland filter
GUID-5F 013F78-E E34-4C18-B FFB-79938 408A1A2
JVM0161X
MRA8DE engine model
SDI2652
MR16DDT engine model
JVM0081X
MRA8DE andMR16DDT engine model
SDI2722
HR16DE enginemodel
*
1
Oil filler cap
*
2
Oil drain plug
*
3
Oil filter
1. Place alarge drainpanunder thedrain plug.
2. Remove thedrain plugwithawrench.
3. Remove theoilfiller capand completely drainthe
oil.
If the oilfilter isto be changed, removeand
replace itat this time.
CAUTION:
Waste oilmust bedisposed ofproperly. Check
your local regulations.
4. Loosen theoilfilter withanoilfilter wrench.
5. Remove theoilfilter byturning itby hand.
6. Wipe theengine oilfilter mounting surfacewitha
clean cloth.
Be sure toremove anyoldgasket remaining onthe
mounting surface.
7. Apply newengine oiltothe gasket ofthe new oil
filter.
8. Screw inthe oilfilter untilaslight resistance isfelt
and then tighten anadditional 2/3ofaturn to
secure thefilter.
Oil filter tightening torque:
15 to20 N´m
(1.5 to2.0 kg-m, 11to15 ft-lb)
9. Clean andreinstall thedrain plugandnew washer.
Securely tightenthedrain plugwithawrench. Do
not use excessive force.
Drain plugtightening torque:
29 to39 N´m
(3.0 to4.0 kg-m, 22to29 ft-lb)
10. Refill therecommended engineoiland quantity .
(See ªRecommended fluids/lubricantsandcapa-
citiesº (P.9-2) .)
When fillingtheengine oil,donot remove
the dipstick (exceptforHR16DE engine
model) .
11. Securely installtheoilfiller cap.
&RQGLWLRQ


> (GLW   0RGHO &$@
GUID-85F3 A377-AEC4-4 B2C-8B1A-DCA92F23BD68
Contact aNISSAN dealerifchecking orreplacement
is required.
CAUTION:
. Use only Genuine NISSANCVTFluid NS-3.
Do not mix with other fluids.
. Using transmission fluidother thanGenuine
NISSAN CVTFluid NS-3willdamage the
CVT ,which isnot covered bythe warranty.
GUID-31654B FB-7FD1-4485-8577-CE C93F60D8BD
SDI2667
WARNING:
Operating theengine withtheaircleaner filter
off can cause youorothers tobe burned. Theair
cleaner filternotonly cleans theintake air,it
also stops flame ifthe engine backfires. Ifthe air
cleaner filterisnot installed andtheengine
backfires, youcould beburned. Neverdrivewith
the aircleaner filteroff.Becautious workingon
the engine whentheaircleaner filterisoff.
T o remove thefilter, pulltheairduct
*
1
upward to
remove it.Pull thetabs
*
2
, then pullthecover
*
3
upward.
The viscous papertypefilterelement shouldnotbe
cleaned andreused. Thedrypaper typefilterelement
may becleaned andreused. Replace theairfilter
according tothe maintenance logshown inaseparate
maintenance booklet.
When replacing theairfilter, wipetheinside ofthe air
cleaner housing andthecover withadamp cloth.
GUID-1E8 7C0C3-19A 7-495E-AF4 8-A77448AE4962
WINDSHIELD WIPERBLADES
GUID-CB3E 500E-FF38-4 A23-B90C-E296B23CFC7 A
Cleaning
GUID-1F848 096-A502-4F6 2-82A8-5DCF0E18CBBB
If the windshield doesnotbecome clearafterusing the
windshield washerorifthe wiper blades chatter when
operating thewindshield wipers,waxorother materials
may beonthe windshield and/orwiperblades.
Clean theoutside ofthe windshield surfacewitha
washer solution ormild detergent. Your windshield is
clean ifbeads donot form when rinsing withwater.
Clean theblade bywiping itwith acloth soaked ina
washer solution oramild detergent. Rinsetheblade
with water. Ifyour windshield isstill notclear after
cleaning theblades andusing thewipers, replace the
blades.
Maintenance anddo-it-yours elf
8-15
CONTINUOUSL
YVARIABLE
TRANSMISSIO N(CVT) FLUID (if
equipped) AIR
CLEANER FILTER WIPERBLADES
&RQGLWLRQ


> (GLW   0RGHO &$@
8-16
Maintenance anddo-it-yours elf
SDI1865
Be careful nottoclog thewasher nozzle
*
A
. This may
cause improper windshield washeroperation. Ifthe
nozzle isclogged, removeanyobjects withaneedle or
small pin
*
B
. Be careful nottodamage thenozzle.
Replacing
GUID-446 2DA2C-A6A5 -41D7-9863-C47C1EA4 8EA4
SDI1649
Replace thewiper blades ifthey areworn.
Before replacing thewiper blades, thewiper should be
in the fully upposition toavoid scratching theengine
hood ordamaging thewiper arm.To pull upthe wiper
arm, seeªWiper andwasher switchº (P.2-20) .
1. Liftthe wiper armaway fromthewindshield.
2. Push andhold therelease tab
*
A
, and then move
the wiper blade downthewiper armtoremove
*
1
.
3. Remove thewiper blade.
4. Insert thenew wiper blade ontothewiper armuntil
it clicks intoplace.
CAUTION:
. After wiper blade replacement, returnthe
wiper armtoits original position. Otherwise
the wiper armorthe engine hoodmaybe
scratched andmay cause damage whenthe
engine hoodisopened.
. Worn wiper blades candamage thewind-
shield andimpair drivervision.
REAR WINDOW WIPERBLADE
GUID-BFB 99CBF-6874-4939-8C 1C-B539C65 1C360
Contact aNISSAN dealerifchecking orreplacement
is required.
&RQGLWLRQ


> (GLW   0RGHO &$@
GUID-7DA1 8CA2-4A81- 4DD7-B18F-1 925A54D06 B4
SDI2475
WARNING:
Anti-freeze ispoisonous andshould bestored
carefully inmarked containers outofthe reach
of children.
T o check thefluid level, useyour finger toplug the
center hole
*
1
of the cap/tube assembly,then remove
it from thereservoir.
If there isno fluid inthe tube, addfluid.
Add awasher solventtothe water forbetter cleaning.
In the winter season, addawindshield washeranti-
freeze. Followthemanufacturer's instructionsforthe
mixture ratio.
Maintenance anddo-it-yours elf
8-17
WINDOW
WASHERFLUID
&RQGLWLRQ