2017 NISSAN PULSAR check oil


> (GLW   0RGHO &$@
GUID-B1 20ADA3-D0 3C-49B1-B529-7A274B D909D0
CHECKING ENGINEOILLEVEL
GUID-7F B3D707-0 60C-4B57-B BE7-3BDD80ACE30 5
SDI1993
T ype A
SDI2721
T ype B
1. Park thevehicle onalevel surface andapply the
parking brake.
2. Start theengine andwarm itup until theengine
temperature reachesthenormal operating tem-
perature (approximately 5minutes) .
3. Stop theengine.
4. Wait atleast 10minutes forthe engine oiltodrain
back tothe oilpan.
5. Remove thedipstick andwipe itclean. 6.
Reinsert thedipstick allthe way.
7. Remove thedipstick andcheck theoillevel. It
should bewithin therange
*
C
.
8. Ifthe oillevel isbelow
*
A
, remove theoilfiller cap
and pour therecommended oilinto theopening.
Do not overfill
*
B
.
When fillingtheengine oil,donot remove
the dipstick.
9. Recheck theoillevel withthedipstick.
It is normal toadd some oilbetween oil
maintenance intervalsorduring thebreak -in
period, depending onthe severity ofoperat-
ing conditions.
CAUTION:
The oillevel should bechecked regularly.
Operating yourvehicle withaninsufficient
amount ofoil can damage theengine, andsuch
damage isnot covered bythe warranty.
CHANGING ENGINEOILAND OILFILTER
GUID-BFC63 F3B-A179-42CF-BDF1-B 43386889AD1
WARNING:
. Used oilmust bedisposed ofproperly. Never
pour ordump oilinto theground, canals,
rivers, etc.It should bedisposed ofatproper
waste facilities. NISSANrecommends hav-
ing your oilchanged byaNISSAN dealer.
. Be careful nottoburn yourself, asthe
engine oilmay behot.
. Prolonged andrepeated contactwithused
engine oilmay cause skincancer.
. Avoid directskincontact withused oil.If
contacted, washthoroughly withsoap or hand
cleaner andplenty ofwater assoon as
possible.
. Store usedengine oilinmarked containers
out ofthe reach ofchildren.
1. Park thevehicle onalevel surface andapply the
parking brake.
2. Start theengine andwarm itup until theengine
temperature reachesthenormal operating tem-
perature (approximately 5minutes) .
3. Stop theengine.
4. Wait atleast 10minutes forthe engine oiltodrain
back tothe oilpan.
5. Raise andsupport thevehicle usingasuitable
floor jackandsafety jackstands.
.
Place thesafety jackstands underthevehicle
jack -up points.
.
A suitable adaptershouldbeattached tothe
jack stand saddle.
6. For HR16DE enginemodel,remove theplastic
engine undercover.
.
Remove thebolts andplastic clipsfromthe
undercover.
Maintenan ceand do-it-you rself
8-9
ENGINE
OIL
&RQGLWLRQ


> (GLW   0RGHO &$@
8-10
Maintenance anddo-it-yours elf
Engine oiland filter
GUID-5F 013F78-E E34-4C18-B FFB-79938 408A1A2
JVM0161X
MRA8DE engine model
SDI2652
MR16DDT engine model
JVM0081X
MRA8DE andMR16DDT engine model
SDI2722
HR16DE enginemodel
*
1
Oil filler cap
*
2
Oil drain plug
*
3
Oil filter
1. Place alarge drainpanunder thedrain plug.
2. Remove thedrain plugwithawrench.
3. Remove theoilfiller capand completely drainthe
oil.
If the oilfilter isto be changed, removeand
replace itat this time.
CAUTION:
Waste oilmust bedisposed ofproperly. Check
your local regulations.
4. Loosen theoilfilter withanoilfilter wrench.
5. Remove theoilfilter byturning itby hand.
6. Wipe theengine oilfilter mounting surfacewitha
clean cloth.
Be sure toremove anyoldgasket remaining onthe
mounting surface.
7. Apply newengine oiltothe gasket ofthe new oil
filter.
8. Screw inthe oilfilter untilaslight resistance isfelt
and then tighten anadditional 2/3ofaturn to
secure thefilter.
Oil filter tightening torque:
15 to20 N´m
(1.5 to2.0 kg-m, 11to15 ft-lb)
9. Clean andreinstall thedrain plugandnew washer.
Securely tightenthedrain plugwithawrench. Do
not use excessive force.
Drain plugtightening torque:
29 to39 N´m
(3.0 to4.0 kg-m, 22to29 ft-lb)
10. Refill therecommended engineoiland quantity .
(See ªRecommended fluids/lubricantsandcapa-
citiesº (P.9-2) .)
When fillingtheengine oil,donot remove
the dipstick (exceptforHR16DE engine
model) .
11. Securely installtheoilfiller cap.
&RQGLWLRQ


> (GLW   0RGHO &$@
12. Start theengine.
13. Check thedrain plugforany sign ofleakage.
14. Dispose ofthe used oilinthe proper manner.
Check yourlocal regulations.
15. Check theengine oillevel according tothe proper
procedure. (SeeªChecking engineoillevelº (P.8-
9) .)
After theoperation
GUID-D31 C7ECF-FDA1 -4CF1-B6A7-3C0771BAD AF0
1. For HR16DE enginemodel,installtheengine
undercover intoposition asthe following steps.
a. Pull thecenter ofthe small plastic clipout.
b. Hold theengine undercover intoposition.
c. Insert theclip through theundercover intothe
hole inthe frame, thenpush thecenter ofthe
clip into lock theclip inplace.
d. Install theother boltsthathold theundercover
in place. Becareful nottostrip thebolts or
over-tighten them.
2. Lower thevehicle carefully tothe ground.
3. Dispose ofwaste oiland filter properly .
GUID-4B 37DD34-9 FBB-48DA-870 F-42F8858 0E4D7
SDI1881
MRA8DE andMR16DDT enginemodel
1. Alternator
2. Drive beltauto-tensioner
3. Crankshaft pulley
4. Airconditioner compressor
5. Water
pump
SDI1862
HR16DE enginemodel
1. Water pump
2. Alternator
3. Crankshaft pulley
4. Airconditioner compressor
!: Tension checking point
Be sure theignition switchisin the ªOFFº position. Visually
inspectthebelt forsigns ofunusual wear,cuts,
fraying orlooseness. Regularlycheckthecondition
and tension (forHR16DE enginemodel).If the belt is
in poor condition orloose, haveitreplaced oradjusted
by aNISSAN dealer.
Maintenance anddo-it-yours elf
8-11
DRIVE
BELT
&RQGLWLRQ


> (GLW   0RGHO &$@
8-20
Maintenance anddo-it-yours elf
3. Replace thebattery withanew one.
Recommended battery:CR1620 orequivalent
.
Do not touch theinternal circuitandelectric
terminals asdoing socould cause amalfunc-
tion.
.
Make surethatthe+side faces thebottom of
the case
*
C
.
4. Close thelidand install thescrew securely .
5. Operate thebuttons tocheck itsoperation.
See aNISSAN dealerifyou need assistance for
replacement.
INTELLIGENT KEYBATTER Y
GUID-DF 12F1B1-793 B-42C2-A0D7-466ECF 2BE1FA
Battery replacement
GUID-D30 A852B-CF0 1-4B8D-A3A3- 742BD4A4C40D
CAUTION:
. Becareful nottoallow children toswallow
the battery andremoved parts.
. Animproperly disposedbatterycanharm
the environment. Alwaysconfirm localreg-
ulations forbattery disposal.
. When changing batteries, donot letdust or
oil get onthe components.
. There isdanger ofexplosion iflithium
battery isincorrectly replaced.Replaceonly
with thesame orequivalent type.
. Donot expose thebattery toexcessive heat
such assunshine, fire,etc
.
SDI2451
T o replace thebattery:
1. Release thelock knob atthe back ofthe Intelligent
K ey and remove themechanical key.
2. Insert asmall screwdriver intotheslitofthe corner
and twist itto separate theupper partfrom the
lower part.Useacloth toprotect thecasing.
3. Replace thebattery withanew one.
.
Recommended battery:CR2025 orequivalent
.
Do not touch theinternal circuitandelectric
terminals asdoing socould cause amalfunc-
tion.
.
Make surethatthe+side faces thebottom of
the case.
SDI2452
4. Align thetips ofthe upper andlower parts
*
1
,
and then push them together untilitis securely
closed
*
2
.
5. Operate thebuttons tocheck itsoperation.
See aNISSAN dealerifyou need assistance for
replacement.
&RQGLWLRQ


> (GLW   0RGHO &$@
N
New vehicle break-in...
............................................ ........5-2
NISSAN Anti-Theft System (NATS) key...
.................. 3-2
O
Oil
Checking engineoillevel ...
...................................... 8-9
Engine oil...
............................................ .......................8-9
Operating precautions ...
............................................... 5-20
Outside airtemperature display...
................................ 2-8
Overheat, Ifyour vehicle overheats ...
.......................... 6-7
P
Panic alarm...
............................................ .......................3-12
Parking
Brake break-in...
....................................... ................5-23
Parking brakeoperation ...
..................................... 5-25
Phone, Bluetooth